RS485/RS232/Serial transport class for mysensors.org
-
@hausinger if you know about coding..
- plain C lib for esp8266, it can be adapted to work with Arduino Esp: https://github.com/plieningerweb/esp8266-software-uart
- or use stock arduino esp8266 software serial lib (https://github.com/plerup/espsoftwareserial), and inspire yourself from lib above, and code your CE pin management..
-
How about adding the following define to use the Serial1/2 on Mega. I have not tested yet but assuming the AltSoftSerial lib has the same interface/functionality it should work.
#define MY_RS485_SERIAL Serial1diff --git a/core/MyTransportRS485.cpp b/core/MyTransportRS485.cpp index 814f721..ea35c9e 100644 --- a/core/MyTransportRS485.cpp +++ b/core/MyTransportRS485.cpp @@ -92,7 +92,11 @@ unsigned char _recSender; unsigned char _recCS; unsigned char _recCalcCS; +#if defined(MY_RS485_SERIAL) +HardwareSerial& _dev = MY_RS485_SERIAL; +#else AltSoftSerial _dev; +#endif unsigned char _nodeId; -
@hek Thanks for the quick response. I'm looking for some direction (this might not be the right forum).
I want to create a node to control my Itho Ecofan ventilation box. I now have a working program (thanks to the help of Rogier Reedijk The nodo now uses a CC1101 transceiver to control the box and thus uses the SPI bus. I'm looking for some direction to use this transmitter as part of my sensor network so I can control it from my Domoticz. Hope you can give me some directions how to proceed. -
Hello,
I have a problem running gatewayserial to rs-485 and the node with the usual lightsensor.
NODE # 1 as a gateway and tried to upload a sketch of the library 2.0 and 1.5.4, and the monitor serial I can not see any data, I use to check on the serial PuTTy com6 because the converter rs-485 to USB is connected to the PC.NODE # 2 as a light sensor, during the upload Sketch by arduino programmer for serial monitor can see the data being sent but after plugging arduino to rs-485 as below no longer visible.
My question is whether I have something wrong with the connection or sketch, can someone show an example of a complete sketch for the gateway, and a node?
Connection mine looks like this:
TX and RX Connect was to pins 0 and 1 in arduino or 8 and 9, DE is always PIN 2.
-
so this is a 1 to 1 setup right? There is nothing here for multiple serial nodes correct?
-
Looks like you got the pins to the Arduino wrong.
Pin 9 >>> DI
Pin 8 >>> RO
Pin 2 >>> DE and RE@hek
On the pictures is connect to TX and RX pins arduino but I tried to connect to pins 8,9,2 and result was the same :(
On thsi connections with pins 8,9,2 ofcourse and library mysensors 2.0 should works fine ? -
Hello,
I have a problem running gatewayserial to rs-485 and the node with the usual lightsensor.
NODE # 1 as a gateway and tried to upload a sketch of the library 2.0 and 1.5.4, and the monitor serial I can not see any data, I use to check on the serial PuTTy com6 because the converter rs-485 to USB is connected to the PC.NODE # 2 as a light sensor, during the upload Sketch by arduino programmer for serial monitor can see the data being sent but after plugging arduino to rs-485 as below no longer visible.
My question is whether I have something wrong with the connection or sketch, can someone show an example of a complete sketch for the gateway, and a node?
Connection mine looks like this:
TX and RX Connect was to pins 0 and 1 in arduino or 8 and 9, DE is always PIN 2.
