Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Arduino Leonardo +nrf24l01

Fat Fly 11 Feb 2016, 19:27 last edited by

How to connect ? I look thousends pictures. But no luck I want to try electricity meter.
Reply Quote 0
1 Reply Last reply
Loading More Posts
3
Posts

4.4k
Views
Reply

Reply as topic
Log in to reply
mfalkvidd Mod 11 Feb 2016, 19:37 last edited by

Leonardo pinout from http://forum.arduino.cc/index.php?topic=148308.0

How to connect the radio: http://www.mysensors.org/build/connect_radio

How far did you get and what were the results? It is a bit hard to help you without knowing that.
Reply Quote 0
1 Reply Last reply
Fat Fly 15 Feb 2016, 04:55 last edited by

@mfalkvidd said:

How far did you get and what were the results? It is a bit hard to help you without knowing that.

I try at evening, after work.
Reply Quote 0
1 Reply Last reply

3
Posts

4.4k
Views

Log in to reply

1 out of 3

Suggested Topics

Update RF24 library to latest version
Bug Reports • 23 Mar 2014, 23:37 • andriej 24 Mar 2014, 22:52

4

0
Votes

4
Posts

2.6k
Views

24 Mar 2014, 22:52

@andriej Hi, I had problem using the main branch mysensors/Raspberry, that because of the bit-field struct (header_s) in Sensor.h They will get packed in different order on the arduino compared to the RPi (at least with my compiler, gcc). In order to fix this I created the 1.4dev branch. It uses full bytes instead of the bit-fields, but you need (of cause) to compile both the sensors (arduino) and the gateway (RPi) using the 1.4dev branch. We need to fix this in the main branch later on (and use the same files as in mysensors/Arduino/libraries/MySensors)
Human presence sensors....
General Discussion • 31 Jan 2025, 10:54 • skywatch 9 Feb 2025, 19:36

13

0
Votes

13
Posts

60
Views

9 Feb 2025, 19:36

@CodeGarage What I want is a lion powered Sensor if possible. And that in a case I can stick to the door frame. As I cannot screw or drill into the doorframe. But I have no idea how much current that draws.
Why is the output of ACS712 current measurement module unchanged?
General Discussion • mysensors • 19 Jul 2021, 09:09 • Tessie T about 10 hours ago

4

0
Votes

4
Posts

33
Views

about 10 hours ago

@ZenBlizzard in case you are measuring the output with a multimeter, you will get an averaged level, since AC current waveform should be sinusoidal and overlapped with the Vcc/2->2.56V in your case. To measure the current you need a decently high sampling and some math. #define SENSITIVITY 66 // mV/A const float readings = 5; const float alpha = 2.0 / (2 * readings + 1); for (ifor = 0; ifor < 250; ifor++) { // Voltage voltageSampleRead = analogRead(V) * vccRead / 1023 - vccRead / 2; /* read the sample value including offset value*/ voltageSampleSum = voltageSampleSum + sq(voltageSampleRead); /* accumulate total analog values for each sample readings*/ voltageSampleOffsetSum = voltageSampleOffsetSum + voltageSampleRead; // Current currentSampleRead = analogRead(I) * vccRead / 1023 - vccRead / 2; /* read the sample value including offset value*/ currentSampleSum = currentSampleSum + currentSampleRead * currentSampleRead; /* accumulate total analog values for each sample readings*/ currentSampleOffsetSum = currentSampleOffsetSum + currentSampleRead; wait(1); } voltageMean = voltageSampleSum / ifor; /* calculate average value of all sample readings taken*/ voltageOffset = voltageSampleOffsetSum / ifor; reading = (sqrt(voltageMean) - voltageOffset) * 230.0 / 1.0; // read voltage / reported voltage. voltage = round_to_dp(alpha * reading + (1 - alpha) * voltage,1); Serial.println(voltage); if (voltage < 25) voltage = 0; currentMean = currentSampleSum / ifor; /* calculate average value of all sample readings taken*/ currentOffset = currentSampleOffsetSum / ifor; reading = (sqrt(currentMean) - currentOffset) / SENSITIVITY * 1000 - currentZeroOffset; // subtract no load current. if (reading < 0) reading = 0; current = round_to_dp( alpha * reading + (1 - alpha) * current,2);
Code Garage to the rescue.
General Discussion • 11 Jan 2025, 11:25 • skywatch 23 Feb 2025, 14:57

9

1
Votes

9
Posts

125
Views

23 Feb 2025, 14:57

I hope the project won't be buried due to the fact that the protocol is the basis of nippy devices (https://nippysmart.com/) I also hope that the development of mysensors won't be directed in 2 directions - one commercial only for nippy - the other for all the rest, which could result in the two versions diverging so much that they will be incompatible and the second one will simply be buried.
Which device I have to use to connect with accelerometer before connecting to my pc?
General Discussion • 24 Jan 2023, 17:16 • Yada Kijsathan 13 days ago

5

1
Votes

5
Posts

40
Views

13 days ago

When connecting an accelerometer to your PC, consider its communication protocol (I2C or SPI) and the appropriate interface device, like a microcontroller (e.g., Arduino). You may also need additional hardware for voltage adjustment or signal conditioning, depending on the sensor’s specifications.
Combination of networks
General Discussion • 1 Feb 2025, 17:30 • Sniker 4 Feb 2025, 01:02

4

0
Votes

4
Posts

22
Views

4 Feb 2025, 01:02

Take a look on this article https://www.mysensors.org/build/rs485

0
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1