Chinese Solar Lipo powered PIR led lamp.

[gyro]

I think "mysensors" aware chinese LED solar lamp could work with a little effort, prototype is working now ( thanks to the forum members for help)
What needs to be done:

• disconnect BISS0001 pin 2 from circuit (i have cut circuit wire on the back of PCB)

• connect BISS0001 pin 2 to input pin 3 of arduino pro mini (3,3 V model)

• connect resistor R9 (smd 102 - 1kohm) to output pin 4 of arduino which drives the transistor(Y1) base

• i think that the easiest way would be to remove resister R9 from circuit. Then connect left part of resistor to input pin of arduino,

• then wire to arduino output (pin 4) resistor 1K and then connect to right part of removed transistor.

Now i can use the solar light as motion detection and control LED lights independantly.

• motion detection works all day,

Received PUBLISH (d0, q0, r0, m0, 'mygateway1-out/11/12/1/0/16', ... (1 bytes))
0
Received PUBLISH (d0, q0, r0, m0, 'mygateway1-out/11/12/1/0/16', ... (1 bytes))
1

but i can control the lights

root@kali:~# mosquitto_pub -d -h 192.168.1.115 -t "mygateway1-in/11/1/1/0/2" -m "1"
Received CONNACK
Sending PUBLISH (d0, q0, r0, m1, 'mygateway1-in/11/1/1/0/2', ... (1 bytes))
root@kali:~# mosquitto_pub -d -h 192.168.1.115 -t "mygateway1-in/11/1/1/0/2" -m "0"

only when they are not charging (someone would need to figure out how to connect/disconnect
the solar charging - circuit now automatically disconnects the LEDs when there is voltage on solar cell and the battery is charging)

usage example:

• with many solar lights on the garden if motion is detected on one we can light on all of them,

• they can all blink as an alarm, (i would need help with code)

• when we need light we can turn lights on from mobile app

• or any other usage (control something that can be controlled with the power of lipo battery )

• I think it would be good idea to meassure battery voltage, what divider should i use to meassure Lipo battery voltage, when arduino is powered from 3.0V battery (solar lamp onboard regulator is 3.0V), that we dont drain battery to much

i have combined motion detection and relay scetch:
the code is below (its not optimized, but it works):

// Enable debug prints
#define MY_DEBUG
#define MY_NODE_ID 11 
// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#include <SPI.h>
#include <MySensor.h>

unsigned long SLEEP_TIME = 120000; // Sleep time between reports (in milliseconds)
#define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define INTERRUPT DIGITAL_INPUT_SENSOR-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define CHILD_ID 12   // Id of the sensor child

boolean lastMotion = false;

// Initialize motion message
MyMessage msg(CHILD_ID, V_TRIPPED);

#define RELAY_1  4  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define NUMBER_OF_RELAYS 1 // Total number of attached relays
#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay

void setup()  
{  
  pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
    
    for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);   
    // Set relay to last known state (using eeprom storage) 
    digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
  }
}

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Motion Sensor and pir", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_MOTION);
    for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
    // Register all sensors to gw (they will be created as child devices)
    present(sensor, S_LIGHT);
  }
}

void loop()     
{     
  // Read digital motion value
  boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 
        
 if (lastMotion != tripped) {
  Serial.println(tripped);
  lastMotion = tripped;
  send(msg.set(tripped?"1":"0"));  // Send tripped value to gw 
 }
  // Sleep until interrupt comes in on motion sensor. Send update every two minute. 
  //sleep(INTERRUPT,CHANGE, SLEEP_TIME);
}

void receive(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type==V_LIGHT) {
     // Change relay state
     digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
   } 
}

[GertSanders]

very nice to see that good progress was made :-)

[soif]

@gyro
Keep up the good work debugging this chinese box !

This box is a really good value for money box to build mysensors projects ( at least box + lipo + solar panel).

If your investigations let us to also use the built in Charger / PIR / LEDS , it would just be amazing.

Please keep us in touch ! ;-)

[gyro]

@soif , @GertSanders
some progress was made, but i need an hardware advice.

This is the part of schematic that drives the LEDs.

First the battery is not connected directly (as here in schematic) but over protection IC logic.

Question 1:

Current circuit works as follows:

• When solar cell voltage is higher than 0.7V , LED is OFF (sort off day/night sensor).
• When solar voltage is lower than 0,7V, LED is shining with low intensity

What is the the correct way to connect arduino pin D1 to take control over above described default behavior? (disconnect the line at SW4 and remove R9 -1Mohm)?

Question 2:
Which voltage measurement technique (internal reference or reference to regulated Vcc voltage) should i use to meassure Lipo voltage?
What are correct/recommended resistor value for optimal battery utilization.
Should this reference be used: https://github.com/rlogiacco/BatterySense

Would make sense to measure also solar cell voltage?

Question 3:

Is arduino pin D2 connect properly? It control two level LED intensity:
pin HIGH - LED glows with HIGH intensity (between led+ and led- is ~4V) pin LOW LED glows with LOW intensity (between led+ and led- is ~2,5V)

Thanks for help and recommendations

I have asked the same here, but no perfect answer jet:
http://electronics.stackexchange.com/questions/218114/solar-battery-powered-leds-circuit-arduino-controlled

[GertSanders]

@gyro

Since you are using a atmega328p, it does make sense to measure the battery level and solar power level.

If you make a node which does NOT sleep all the time, then monitoring both voltage levels is the starting point to make decisions.

I'm guessing you want to add a node using the battery, so a node that sleeps until something needs to be done.
In that case we need a trigger when the light is bright enough to switch off the leds, and dark enough to switch them on again.

The trigger to wake up from sleep should be a voltage change on pin D2 or D3, and the voltage difference needs to be from below the lowest "HIGH" threshold to above the highest "LOW" threshold. Check the specification for the atmega328 you use, as this depends on the working voltage of the processor.

The question I ask myself is what is the lowest voltage you get from the solar cell ? Looking at the circuit, they use the voltage of the solar cell to open the gate of a transistor, which then pulls the emitter voltage of a transistor to ground, which in turn switches off a second transistor with is feeding the battery current to the LEDs.

Your question of the values of R2 and R11 is actually how to measure voltages over a resistor divider? You can choose any value of resistors, but their ratio is what is important.

To calculate the resistor values:

To measure at a maximum of 5V on an analog pin:

R11 = R2 * (1 - voltage-ratio) / voltage-ratio

To go from 6V to 5V the ratio = 5V / 6V = 0.83

Take R2 as 1M Ohm, then R11 = 1M * (1 - 0.83) / 0.83 = 205K => a common value is 220K

To check: voltage over R2 (which is the input voltage on the analog pin A0)

V(A0) = Vinput * R2 / (R1 + R2) = 6V * 1M / (1M+220K) = 4.9 V

[gyro]

@GertSanders I think i managed to successfully connect arduino with solar lamp.

My prototype is working, and has the following functions:

1. Measure battery voltage (when charging it is alway 100% - makes sense)
2. Measure solar voltage (can be omitted - but resistor should be there for a transistor to work properly)
3. Solar power day/night trigger with transistor as a switch (can be used wake up arduino from sleep)
4. PIR sensor (can be used wake up arduino from sleep)
5. Lights on/off dimmed brightness
6. Lights on/off high brightness ( original resistor R9 -1k was replaced with 4.7k - i think it draws to much current and sometimes hangs arduino)

I will post the code later, but every part works with default "mysensor" examples

How to connect and how to add elements see picture:

[GertSanders]

@gyro
Very nice work !!!!

[Dylano]

higher math for me...
Great...

Can you use the motion seperate from the liight?
And can u use the light with a switch option? [ i will turn on the light when there is motion.. ]
Or is the light switching only on lux?

[gyro]

@GertSanders thanks, you have motivated my research

@Dylano the purpose of this project was exactly what you have asked.

The lamp is now mysensors aware.
Every task can be operated separately.

• When there is dark, the trigger is send, when the sun shines, the trigger is send. (transistor as switch). In scetch i use it as magnet switch part of code. When trigger is received (can wake up arduino), than you decide with controller what you want to do .

• PIR acts as classic PIR sensor and can also be used as trigger. (can wake up arduino), than you decide with controller what you want to do.

• The Lamp have two phases and can be controlled with controller (i control it over mqtt for now)

• phase one is dimmed light (relay 1)

• phase two is high bright light (relay 2)

Below is code that works for now. I wil improve it in next few days

// Enable debug prints
#define MY_DEBUG
#define MY_NODE_ID 11 
// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#include <SPI.h>
#include <MySensor.h>
#include <Bounce2.h>

//unsigned long SLEEP_TIME = 120000; // Sleep time between reports (in milliseconds)
#define DIGITAL_INPUT_SENSOR 2   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
//#define INTERRUPT DIGITAL_INPUT_SENSOR-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define CHILD_ID 12   // Id of the sensor child

boolean lastMotion = false;

// Initialize motion message - start
MyMessage msg(CHILD_ID, V_TRIPPED);

//trigger solar power day on/off -start
#define CHILD_ID_SW 5
#define BUTTON_PIN  5  // Arduino Digital I/O pin for button/reed switch
Bounce debouncer = Bounce();
int oldValue = -1;

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage SolarMsg(CHILD_ID_SW, V_TRIPPED);
// trigger solar - end

#define RELAY_1  3  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define NUMBER_OF_RELAYS 2 // Total number of attached relays
#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay

void setup()
{
	//trigger solar power day on/off - start
	// Setup the button
	pinMode(BUTTON_PIN, INPUT);
	// Activate internal pull-up
	digitalWrite(BUTTON_PIN, HIGH);

	// After setting up the button, setup debouncer
	debouncer.attach(BUTTON_PIN);
	debouncer.interval(5);
	//trigger solar - end


	pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input

	for (int sensor = 1, pin = RELAY_1; sensor <= NUMBER_OF_RELAYS; sensor++, pin++) {
		// Then set relay pins in output mode
		pinMode(pin, OUTPUT);
		// Set relay to last known state (using eeprom storage) 
		digitalWrite(pin, loadState(sensor) ? RELAY_ON : RELAY_OFF);
	}
}

void presentation() {
	// Send the sketch version information to the gateway and Controller
	sendSketchInfo("Motion Sensor and light", "1.0");

	// Register all sensors to gw (they will be created as child devices)
	present(CHILD_ID, S_MOTION);
	for (int sensor = 1, pin = RELAY_1; sensor <= NUMBER_OF_RELAYS; sensor++, pin++) {
		// Register all sensors to gw (they will be created as child devices)
		present(sensor, S_LIGHT);

		// Register binary input sensor to gw (they will be created as child devices)
		// You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
		// If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
		present(CHILD_ID_SW, S_DOOR);
	}
}

void loop()
{
	// Read digital motion value
	boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH;

	if (lastMotion != tripped) {
		Serial.println(tripped);
		lastMotion = tripped;
		send(msg.set(tripped ? "1" : "0"));  // Send tripped value to gw 
	}
	// Sleep until interrupt comes in on motion sensor. Send update every two minute. 
	//sleep(INTERRUPT,CHANGE, SLEEP_TIME);

	//trigger solar power day on/off - start
	debouncer.update();
	// Get the update value
	int value = debouncer.read();

	if (value != oldValue) {
		// Send in the new value
		send(SolarMsg.set(value == HIGH ? 1 : 0));
		oldValue = value;
	//trigger solar power day on/off - stop
	}
}

void receive(const MyMessage &message) {
	// We only expect one type of message from controller. But we better check anyway.
	if (message.type == V_LIGHT) {
		// Change relay state
		digitalWrite(message.sensor - 1 + RELAY_1, message.getBool() ? RELAY_ON : RELAY_OFF);
		// Store state in eeprom
		saveState(message.sensor, message.getBool());
		// Write some debug info
		Serial.print("Incoming change for sensor:");
		Serial.print(message.sensor);
		Serial.print(", New status: ");
		Serial.println(message.getBool());
	}
}```

[Dylano]

mmm i ordered 1...
So i hope i gonna ix this...
It is looking higher mathematics

Will see... when i have time..
Thanks for the sketch!!!
Give it a try in a uno ...

[Dylano]

guess what...
I do have a:
http://www.ebay.com/itm/161885080971?_trksid=p2057872.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Exact the same board in of this light...
I think i going to try the make this work...

Only i do not understand exact the wiring of your example.
Will you please make a list of exact stuff to buy.
And make some more pictures, from the good places..

And a thing that i see.
You use D2 from the arduino.
Is that not a one for the radio?

[siklosi]

@gyro is there a reason you used high/low intensity with resistor instead of PWM?

[gyro]

@siklosi Resistor is used as transisistor base resistor. This was the best way to connect i could think off. But you need two output pins - 2 transistors are controlled.
first PIN - lights ON/OFF
second PIN - ligths bright ON/OFF

[gyro]

@Dylano Great to hear that the light has the same board...please post a picture.
My light is still protoype connected together on protoboard - connected to arduino pro mini - i can post only a picture connected elements on protoboard for now.
I am trying to put all together in openhab now.
I will try to make a list of exact elements.
I have free D2 pin on arduino pro mini.

[readykal]

As the easiest way to disable dimmed mode this lamp?

[korttoma]

Got myself a similar PIR LED lamp. The functionality seems like it is the same but the circuit board is different.

[gyro]

@korttoma
Nice to see some interest in smart solar lamps :)
It looks like an updated version (at least i like it more from your pictures). Could you post an order link.
I think this one should be even easier to intercept with "mysensors", beacause i see only two transistors and circuit connectios are clearly visible.

so lets try to understand the circuit:
-U3 is probably battery protection circuit

• Q1 i think is voltage regulator HT33 - to power arduino wih 3.3V (meassure voltage)
• take a photo of PIR sensor from front side (is there any ic elements)?
• U1 - i would guess PIR sensor IC logic - leg 6 (count from dot on IC) should be output (meassure voltage - high 3,3 V when motion detected):
  -if it is output from PIR just remove R3 and IC ouput goes over resistor to you arduino input.
• the output goes over resistor to Q2
  -whats is left - you have to figure out what drives resistor Q1(J3y) :
• i gues its driven by solar cell, than collector is connected to resistor R10, resesitor is than connected over board to the other side.......

[korttoma]

I guess you meant U4 is the 3.3V regulator. I measured it to 3.3V and HT33 should be a regulator. Q1 and Q2 I think are transistors. U3 handles the solar charging. U1 is for the PIR but unfortunately there is no text on the chip. I will get you the link tomorrow but it is quite easy to find on aliexpress.

[gyro]

@korttoma
sorry my typo: you are correct

• U4 - HT33 is voltage regulator
• yes Q1 and Q2 are transistors
• U1 - PIR out test - measure voltage between PIN 6 and R3 when PIR is OF and ON. I think this drives Q2 (high brightness / low brightnes)

also take picture of other side of circuit board, beause i think Q1 is conected to R10 and
then further on the other side

[korttoma]

Here is the link to the one I got but it seems like the prize is allot higher now since I paid 23,84$ including shipping -> http://www.aliexpress.com/item/1-Set-1200-Lumens-46-pcs-LED-Solar-Power-Motion-Sensor-Lamp-Ultra-thin-PIR-Outdoor/32354254209.html

Also it took like 10 weeks for it to arrive so maybe another seller would be a better fit.