MYSBootloader 1.3 pre-release & MYSController 1.0.0beta

[Jan Hicl]

Hi @tekka, I'm having the very same issue as @Mickey so I just wanted to ask if there is any workaround to that or if happen to make the adjustment to the bootloader. Thanks a lot! Original comment

[tekka]

@Jan-Hicl This has been fixed - did you try the most recent version from github?

[Jan Hicl]

Hi @tekka and thanks for getting back to me! I tried the latest version however with no success. The node that I update is still marked as "Booting" even though I upload Blink.hex. Strangely enough, the led is blinking as it's supposed to blink and if I request presentation the node replies with correct sketch name but then it goes back to Booting. I'm using Arduino IDE 1.8.1, AVRdude v6.1 and MYScontroller v1.0.0 beta (build 3314). I'm using Arduino mini pro, 3V3, 8MHz. I have 5 different nodes but all of them with the same behavior so it does not seem as an HW issue.

Here is my log from the upload of Blink.hex: http://pastebin.com/9grgHb27 Would you have any idea how could I fix that? Thanks!

[tekka]

@Jan-Hicl The blink sketch is somewhat special - it only blinks the built-in LED until the watchdog kicks in and resets the node. What happens if you upload one of your sketches? Please post the full debug log + source. Thanks

[yd kim]

I did success with MySBootloader 1.3 beta 3 (https://github.com/mysensors/MySensorsBootloaderRF24 )
It works both arduino and OTA firmware upgrade however it takes longer to boot up (means switch to firmware) about 3-5seconds.
I'm using MYSensors 2.1.0 and MYController (http://www.mycontroller.org) on arduino pro mini 8Mhz 3.3V.

How many sensor you try at the same time?
From memory When I do firmware update for 3-4 sensors, I have to change "Tx message processing delay" to 300ms.
If it's shorter than 300ms, keep rebooting some stage.

I didn't use MYScontroller but probably it has similar setting.

[Jan Hicl]

Thanks @tekka for a prompt response!

I tried to upload https://github.com/mysensors/MySensors/blob/master/examples/AirQualitySensor/AirQualitySensor.ino
here is the log: http://pastebin.com/Tc5vhEnF
You can see that the node is successfully running with TimeReporter but AirQualitySensor cannot make it from booting. However, this is happening even with highly modified AirQualitySensor sketch or some of my custom sketches. In the log, you can also see that if I request presentation of that node it replies with correct sketch name.

Please let me know if you need some more info. Thanks in advance!

[tekka]

@Jan-Hicl Please also post the full debug log of the node (running AirQualitySensor).

[Jan Hicl]

@tekka here is the AirQualitySensor node log: http://pastebin.com/XWfFCbUx

[tekka]

@Jan-Hicl The GW and node logs are inconsistent: your GW log shows a rebooting node 1 - the node log shows a running node trying to establish the uplink. Do you have logs from GW and node taken simultaneously?

[Jan Hicl]

Sorry @tekka, should've sent this in the first post. Here is AirQuality sensor node log: http://pastebin.com/9MVtfRNV
Here is gateway log: http://pastebin.com/QNpmBz4m
Both of them logged simultaneously. Node Id I'm updating is 1. In the log you can again see that TimeReporter is working well before the flashing. Please let me know if there is anything I can provide you with in order to solve this... Thanks!

[Nicolas Charrier]

Hello
I succed to program booloader but y can not add my sketch to arduino with serial or USB line.
Is is activated by default?
Thanks.

[Jan Hicl]

Hi @tekka any update what could be wrong with the upload? Any advice on a workaround? Thanks!

[tekka]

@Jan-Hicl The upload via bootloader is ok (the sketch is running - based on your debug log) - so no issue here.
However, you may have some issues with the CPU frequency (wrong board selected when compiling?) - there are scrambled chars in the debug output:

Starting óensor (RNNNA-, 2.0.0)
TSM:INIT
TSM:RADIO:OK
TSP:ASSIGNID:OK (ID=1)
TSM:FPAR
TSP:MSG:ÓEND 1-1-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSP:MSG:READ 0-0-1 s=255,c=3,t=8,pt=1,l=1,sg=0:0
TSP:MSG:FPAR RES (IÄ=0, dist=0)
TSP:MSG:PAR OK (ÉD=0, dist=1)
TSM:FPAR:OK
TSM:ID
TSM:CHKID:OË (ID=1)
TSM:UPL
TSP:PING:SEND (dest=0)
TSP:MSG:SEND 1-1-0-0 s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=ok:1
TSP:CHKUPL:FAIL (hops=255)
!TSM:UPL:FAIÌ
TSM:FPAR
TSP:MSG:SEND 1-1-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSP:MSG:READ 2-2-255 s=255,c=3,t=7,pt=0,l=0,sg=0:
TSP:MSG:BC
TSP:MSG:ÒEAD 0-0-1 s=255,c=3,t=8,pt=1,l=1,sg=0:0
ÔSP:MSG:FPAR RES (ID=0, dist=0)
TSP:MSG:PAR OK (ID=0, diót=1)
TSM:ÆPAR:OK

[Samuel235]

How do we go about compiling this for 8MHz crystal (Internal and External), i'm sure this has already been asked but I can't seem to search through this post very efficiently... Sorry if it has been covered already, just a link back or something would probably suit me if it has been :)

[romeo01]

Nice job, the last bootloader seems to run in good conditions.

I use MySensors 2.2.0 beta, MYSController 1.0.0 (3314) and the last version MYSbootloader 1.3.0-beta.4 (https://github.com/mysensors/MySensorsBootloaderRF24)

Update, flash, firmware via OTA is ok.

But 1 problem occurs when a node reboot.
I tried to isolate the problem, so I think that's arround the presentation request.

When I click on "request presentation", I got it

http://hpics.li/93e8861

and below the debug output (via serial) of the node

70437 TSF:MSG:READ,0-0-1,s=0,c=3,t=19,pt=0,l=1,sg=0:0
70445 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
70453 TSF:MSG:READ,0-0-1,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
70460 TSF:MSG:SEND,1-1-0-0,s=255,c=0,t=17,pt=0,l=10,sg=0,ft=0,st=OK:2.2.0-beta
70469 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
70497 TSF:MSG:READ,0-0-1,s=255,c=3,t=6,pt=0,l=1,sg=0:M
70504 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=11,pt=0,l=8,sg=0,ft=0,st=OK:OTA Test
70512 TSF:MSG:SEND,1-1-0-0,s=255,c=3,t=12,pt=0,l=1,sg=0,ft=0,st=OK:1
70521 TSF:MSG:SEND,1-1-0-0,s=1,c=0,t=3,pt=0,l=8,sg=0,ft=0,st=OK:Sensor 1

Maybe a bug or where is the mistake ?

Thanks in advance foryour help

Edit: After a couple of test, the problem is related to the gateway with MySensor Library version 2.2.0 beta.
All nodes (2.1.1 & 2.2.0 libs) from my network present the same error.
Probably a vartype unexpected by the Gateway (2.2.0 lib).

The serial Gateway (2.1.1) is ok

[ahmedadelhosni]

@Nicolas-Charrier
Hello @tekka , I have the same problem.

I am trying to set up my Serial Gateway. I flashed the OTA bootloader but how can I upload the Gateway sketch through Serial ?

I tried to use the MySysController but the node is not presented so that I can flash new firware with the Gateway sketch. It only worked when I flashed normal Optiboot bootloader and then flashed the Serial Gateway sketch through Serial, then I connected the Gateway to the Controller and the presentation worked well. Thus I now have a Gateway which I can flash other nodes with through OTA.

Is there another way to flash a gateway sketch other than this ?

Thanks.

[tekka]

@ahmedadelhosni Why would you want to flash MYSBootloader on your GW? OTA FW update capabilities only make sense on sensor nodes...

[ahmedadelhosni]

@tekka I just thought that if I flashed a bootloader on a new hardware IC then I can decide whether to flash GW or sensor node when connected to the serial computer.

[ksya]

I see that after compiling I get to choose between sketch.ino.hex and sketch.ino.with_bootloader.hex
Is it possible to update the bootloader OTA by using this hex file instead? Which is the best bootloader available now, because my nodes are now on 1.3pre (from topic start).

[itbeyond]

How does GW mode actually work - I have been trying to relay a connection to Vera but not matter what combination I am trying I cannot understand how the GW mode operates?