Ethernet Gateway without NRF24L01+

[mlg]

@hek

Yes UI7 branch, I already commented these two lines and check the cables, when I press start button the rx and tx lights flashing

[mlg]

for restart sensor a few times, simply disconnect the gnd cable or all cables?

[einarth]

Isn't digital pin 4 used by the Ethernet shield?

Probably not the cause of your problems but just noticed when looking over your code..

[mlg]

@einarth

I already commented this line in the code , my final code

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable gateway ethernet module type 
#define MY_GATEWAY_W5100

// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
//#define MY_W5100_SPI_EN 4  

// Enable Soft SPI for NRF radio (note different radio wiring is required)
// The W5100 ethernet module seems to have a hard time co-operate with 
// radio on the same spi bus.
//#if !defined(MY_W5100_SPI_EN) && !defined(ARDUINO_ARCH_SAMD)
  //#define MY_SOFTSPI
  //#define MY_SOFT_SPI_SCK_PIN 14
  //#define MY_SOFT_SPI_MISO_PIN 16
  //#define MY_SOFT_SPI_MOSI_PIN 15
//#endif  

// When W5100 is connected we have to move CE/CSN pins for NRF radio
//#define MY_RF24_CE_PIN 5
//#define MY_RF24_CS_PIN 6



#define MY_IP_ADDRESS 192,168,1,169   // If this is disabled, DHCP is used to retrieve address
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003        
 
// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
 #define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED

// Flash leds on rx/tx/err
 #define MY_LEDS_BLINKING_FEATURE
// Set blinking period
 #define MY_DEFAULT_LED_BLINK_PERIOD 300

// Enable inclusion mode
 #define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
// #define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
 #define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
// #define MY_INCLUSION_MODE_BUTTON_PIN  4 

#include <SPI.h>
#include <Ethernet.h>
#include <MySensor.h>


#define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define INTERRUPT DIGITAL_INPUT_SENSOR-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define CHILD_ID 1   // Id of the sensor child
boolean lastTripped = 0;


// Initialize motion message
MyMessage msg(CHILD_ID, V_TRIPPED);

void setup()  
{  
   

  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Motion Sensor", "1.0");

  pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_MOTION);
}



void loop()     
{     
  
  // Read digital motion value
  boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 

    if (lastTripped != tripped ) {
      send(msg.set(tripped?"1":"0")); // Send new state and request ack back
      Serial.println(tripped);
      lastTripped=tripped;
}
}

@hek
After other factory reset , start button now work !! but the inclusion no ! I press start and after 1 minute change automatically to stop.

[mlg]

Any Ideia?

[hek]

Inclusion mode is supposed to stop after 1 minute. So it sounds like communication between controller and gateway is fine.

Did you reset the sensor node during inclusion mode was activated?
Have you looked in the gateway debug log (while gateway is connected to your computer)?

[mlg]

@hek

How I make sensor node reset ? Disconnected all cables ? digital pin 3 + gnd + 5v ?

If I disconect all cables I log that

0;255;3;0;9;Starting gateway (R-NGA-, 2.0.0-beta)
IP: 192.168.1.169
0;255;3;0;9;Init complete, id=0, parent=0, distance=0
0;255;3;0;9;Eth: connect
0;255;3;0;9;Eth: 0;0;3;0;5;1
0;255;3;0;9;Eth: 
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0

[mlg]

@hek

It's normal? If I disconnect the cables get 1/0/1/0 and not stopped

[mlg]

@hek

I found one solution,I turn on sensor in ethernet gateway and press start inclusion and reload engine in Vera .In this way automatically add the sensor

However compiled another code by adding a relay but is not added is something wrong?
it is necessary void before, presentation ? and assign a child ID to RELAY ?

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik EKblad
 * Contribution by a-lurker and Anticimex,
 * Contribution by Norbert Truchsess <norbert.truchsess@t-online.de>
 * Contribution by Tomas Hozza <thozza@gmail.com>
 *
 *
 * DESCRIPTION
 * The EthernetGateway sends data received from sensors to the ethernet link.
 * The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
 *
 * The GW code is designed for Arduino 328p / 16MHz.  ATmega168 does not have enough memory to run this program.
 *
 * LED purposes:
 * - To use the feature, uncomment WITH_LEDS_BLINKING in MyConfig.h
 * - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
 * - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
 * - ERR (red) - fast blink on error during transmission error or recieve crc error
 *
 * See http://www.mysensors.org/build/ethernet_gateway for wiring instructions.
 *
 */

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable gateway ethernet module type 
#define MY_GATEWAY_W5100

#define MY_IP_ADDRESS 192,168,1,169   // If this is disabled, DHCP is used to retrieve address
// Renewal period if using DHCP
//#define MY_IP_RENEWAL_INTERVAL 60000
// The port to keep open on node server mode / or port to contact in client mode
#define MY_PORT 5003        
 
// The MAC address can be anything you want but should be unique on your network.
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
// Note that most of the Ardunio examples use  "DEAD BEEF FEED" for the MAC address.
 #define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED

// Flash leds on rx/tx/err
// #define MY_LEDS_BLINKING_FEATURE
// Set blinking period
// #define MY_DEFAULT_LED_BLINK_PERIOD 300

// Enable inclusion mode
 #define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
// #define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
 #define MY_INCLUSION_MODE_DURATION 60 
// Digital pin used for inclusion mode button
// #define MY_INCLUSION_MODE_BUTTON_PIN  4 

#include <SPI.h>
#include <Ethernet.h>
#include <MySensor.h>


#define DIGITAL_INPUT_SENSOR 3   // The digital input you attached your motion sensor.  (Only 2 and 3 generates interrupt!)
#define INTERRUPT DIGITAL_INPUT_SENSOR-2 // Usually the interrupt = pin -2 (on uno/nano anyway)
#define CHILD_ID 1   // Id of the sensor child
boolean lastTripped = 0;

#define RELAY_1  2  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define NUMBER_OF_RELAYS 1 // Total number of attached relays
#define RELAY_ON 1  // GPIO value to write to turn on attached relay
#define RELAY_OFF 0 // GPIO value to write to turn off attached relay


// Initialize motion message
MyMessage msg(CHILD_ID, V_TRIPPED);

void setup()  
{  
   
  // Send the sketch version information to the gateway and Controller
    sendSketchInfo("Motion Relay", "1.0");
 
    pinMode(DIGITAL_INPUT_SENSOR, INPUT);      // sets the motion sensor digital pin as input
  // Register all sensors to gw (they will be created as child devices)
    present(CHILD_ID, S_MOTION);

    for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS;sensor++, pin++) {
    present(sensor, S_LIGHT);
  // Then set relay pins in output mode
    pinMode(pin, OUTPUT);   
  // Set relay to last known state (using eeprom storage) 
    digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
  }
}


void loop()     
{     
  
  // Read digital motion value
  boolean tripped = digitalRead(DIGITAL_INPUT_SENSOR) == HIGH; 

    if (lastTripped != tripped ) {
      send(msg.set(tripped?"1":"0")); // Send new state and request ack back
      Serial.println(tripped);
      lastTripped=tripped;
}
}

void incomingMessage(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type==V_LIGHT) {
     // Change relay state
     digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
     // Store state in eeprom
     saveState(message.sensor, message.getBool());
     // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
   } 
}

[stofakiller]

Hi,

I did'nt have much succes with the radiodevice, and i have made the gateway :-)

But have i missed the code eg for the sensors???

Regards,
Jan