💬 In Wall AC/DC Pcb (with Relay) for MySensors (SMD)

[Martin Nicolaisen]

Hi @sundberg84 does it fit the fuga (scandinavian) wall socket? :=

[sundberg84]

@martin-nicolaisen - Im not familiar with the fuga wall socket.
I use standard round wall sockets (60cm). Can you point me to an image with dimensions ?

[gohan]

@sundberg84 said in 💬 In Wall AC/DC Pcb (with Relay) for MySensors (SMD):

(60cm)

Wow that's quite a wall plug

[sundberg84]

@gohan - lol :)
60mm!!!!

[meanmrgreen]

https://photos.app.goo.gl/JBIVogCZMp0mOCVh2

I must have been drunk when I ordered this. Any idea what I have ordered? I ordered thru dirtypcbs somehow.

Does look a little bit like this PCB but not really. Have I found a early version and drunk ordered 10 of em?

[gohan]

That looks like version 4.1

[Nightbodom]

Hi folks, I manage to solder all the tiny pieces together and now I need some advice on uploading some code/sketch. To start with... is there any instruction for dummies on internet how to upload sketch through ICSP ? I have one arduino which can be programmer, but I don't know how to do it. Then there is question about powering circuit during uploading code.... is it OK if it's connect to AC power during uploading code? And finally, can anyone post some simple sketch for this board to check if everythiing is working? Thanks for help.

[hugch]

@nightbodom Arduino have a tutorial for this https://www.arduino.cc/en/Tutorial/ArduinoISP

[Nightbodom]

@hugch thanks for info. I also find this: https://www.arduino.cc/en/Tutorial/ArduinoToBreadboard for burning bootloader. And after that... how should I upload sketch?

[sundberg84]

@nightbodom you connect it to a ISP programmer to the port. This will take care of 5v and Gnd as well so don't connect to AC during upload

[Nightbodom]

@sundberg84 so I use ISP programmer for burning bootloader... but after that how can i upload sketch... usualy I use FTDI programmer for proMINI ect. but here I don't see TX/RX... so how do you upload sketch?

[sundberg84]

@nightbodom / either you use the isp to program the sketch without the bootloader or you can use the MysX connector where you will find all the necessary pins for ftdi.

[Nightbodom]

@sundberg84 thanks for advice... I successfully load bootloader through ISP with spare Uno as programmer, then I try to load a sketch with ftdi but it didn't recognize PCB. I also try with arduino uno as ISP and it goes without problem. I use node manager sketch with relay and connect it to AC wires...and nothing!
After visual checking of PCB I check fuses and notice that thermal fuse is dead. So I think I burn it with soldering. Any advice how to solder it?

[sundberg84]

@nightbodom - this can be a bit tricky. Some suggest cooling pincers or tongs to hold it while soldering. Myself I solder as normal and wait it to cool down before continue. As long as you are quick and not heat it up to much it should work.

If you power the pcb with FTDI it should work without the fuse though. But I guess you power it through AC->HLK and use only RX/TX/GND and Rst from ftdi?

[ben999]

@nightbodom I use crocodile clips and get fairly good results with very few dead fuses....

[Grave]

Is it possible to use with RFM69 modul?

[gohan]

I guess not on as this module is using SMD NRF24 module

[sundberg84]

@Grave - well @gohan is right, I cant fit a RFM69 module on this board.

[Grave]

I will try to rebuild it in eagle for RFM69. I think the space is there for an RFM69.

[Grave]

Or I will build an adapter.