Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

Working node without MySensors network available

Alexander Ivanov 5 Aug 2016, 18:39 last edited by
Hi Everyone,

I'm building a light switch which should work even if MySensors network is not available.
What I found in MySensors 2.0 is:
- if there's no network available, the system runs only "before" procedure
- once I power on Ethernet gateway (but I haven't done node inclusion), the system runs "before", "setup" and "presentation" procedures, but doesn't run "loop".
How to enable "loop" for my node even if there's no MySensors network available or/and the node wasn't included to the network?

Thanks
Regards, Alexander
Reply Quote 0
1 Reply Last reply 5 Aug 2016, 18:55
Loading More Posts
2
Posts

734
Views
Reply

Reply as topic
Log in to reply
TheoL Contest Winner 5 Aug 2016, 18:55 last edited by @Alexander Ivanov

Dear @Alexander-Ivanov,

Someone asked the same question this week. Continue this thread in that topic https://forum.mysensors.org/topic/4449/how-to-disable-default-node-registration-to-the-gw/2
Reply Quote 1
1 Reply Last reply

2
Posts

734
Views

Log in to reply

2 out of 2

Suggested Topics

Update RF24 library to latest version
Bug Reports • 23 Mar 2014, 23:37 • andriej 24 Mar 2014, 22:52

4

0
Votes

4
Posts

2.6k
Views

24 Mar 2014, 22:52

@andriej Hi, I had problem using the main branch mysensors/Raspberry, that because of the bit-field struct (header_s) in Sensor.h They will get packed in different order on the arduino compared to the RPi (at least with my compiler, gcc). In order to fix this I created the 1.4dev branch. It uses full bytes instead of the bit-fields, but you need (of cause) to compile both the sensors (arduino) and the gateway (RPi) using the 1.4dev branch. We need to fix this in the main branch later on (and use the same files as in mysensors/Arduino/libraries/MySensors)
Running out of nodeId's
General Discussion • mysensors • 3 Sept 2024, 07:33 • NielBierman 25 Jan 2025, 17:19

10

3
Votes

10
Posts

65
Views

25 Jan 2025, 17:19

@GLAB You can set the frequencies using the settings in MyConfig.h, which is in the MySensors folder. If you put any of the defines from MyConfig.h into your sketch, they will override the MyConfig.h setting for that sketch only. If you are using the RF24 radio, there are different channels which correspond to a given frequency. The default is channel 76. There is a list of typical channels in MyConfig.h. If you want to change the channel for all the sketches, change it in MyConfig.h. If you want to change it just for the sketch, add a define to the sketch. For example: #define MY_RF24_CHANNEL (84) The problem with changing the channel in a sketch is that the gateway has to be on the same channel to receive from the node. So, normally it makes sense to change in MyConfig.h because you usually want the gateway and all the nodes on the same channel. Other radio's like the RFM69 list the frequency instead of using a channel. They can be overridden in the sketch as well. You can find the defines that are needed in MyConfig.h
No merge into master in the last 5 years, should we use development?
General Discussion • 23 Sept 2024, 17:48 • kiesel 4 days ago

10

0
Votes

10
Posts

49
Views

4 days ago

Well, my network with two handfulls of nodes in three different locations is still live and kicking! I agree that there does not seem to be a lot happening in the community. I'm running 2.4.0- alpha since this gives support for MQTT over TLS. Just managed today to create one more MQTT GW after reading a lot about support for ESP8266. You know, these things you do once per year and have to learn new each time. MySensors is the cheapest way I have found to create small sensor nodes etc. But now slowly running out of my supply of hardware. Well, time will tell...
Combination of networks
General Discussion • 1 Feb 2025, 17:30 • Sniker 4 Feb 2025, 01:02

4

0
Votes

4
Posts

22
Views

4 Feb 2025, 01:02

Take a look on this article https://www.mysensors.org/build/rs485
Which device I have to use to connect with accelerometer before connecting to my pc?
General Discussion • 24 Jan 2023, 17:16 • Yada Kijsathan 13 days ago

5

1
Votes

5
Posts

40
Views

13 days ago

When connecting an accelerometer to your PC, consider its communication protocol (I2C or SPI) and the appropriate interface device, like a microcontroller (e.g., Arduino). You may also need additional hardware for voltage adjustment or signal conditioning, depending on the sensor’s specifications.
Email notifications received twice
General Discussion • 6 Feb 2023, 16:15 • Jodaille 2 days ago

3

1
Votes

3
Posts

36
Views

2 days ago

It looks like duplicate email notifications may be linked to system settings or preferences. Have you noticed if the issue happens after specific actions or changes? Investigating your notification settings might shed some light

2
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1