💬 Battery Powered Sensors

[gohan]

1 Amp is definitely a lot. I think it can't be a correct reading

[sundberg84]

@FatBeard - as @gohan said - 1A can not be correct. Something is wrong.
If the radio does not work, and the sensors if fishy... I would disconnect it and run the radio/atmega only and fake a sensor value to send and see what happens.

[FatBeard]

@sundberg84 @gohan. Apologies , that's a typo on my part. It jumps to 1ma do 60ms from 6ua. Which I'm happy with I think. My question was more how I can measure it properly. The multimeter seems to be effecting the circuit.

[sundberg84]

This post is deleted!

[gohan]

@FatBeard actually what you really need to measure is the sleep current as it is the state where the node will be spending all of its time. Where are you connecting the multimeter for measuring current?

[FatBeard]

@gohan between positive end of one of the two aa batteries and where it enters circuit. If I start off by having battery connected, the release it slowly with the multimeter attached and without breaking circuit I get my 6ua. However after the timer runs out and the radio comes back on I'm stuck at 1ma. The radio at that point doesn't want to work and it doesn't return to 6ua

[Yveaux]

@FatBeard the burden voltage of your multimeter might be too large, which would reduce the voltage to the atmega below its working level.
You're measuring current, so the meter must be in series with the power supply. It's not clear to me how you can remove the multimeter without breaking power to the atmega.

[gohan]

You could try to add a booster to power the Arduino or change the multimeter 😀

[sineverba]

Hi to all!
I have a issue reading of voltage on pin A0 of an ATMEGA 328 barebone mounted on a breadboard.

This is the image

The purple pin goes to A0.

The rail on the bottom coming direct from batteries, with a multimeter I read that they have 2.73V. On monitor serial, % of battery is about 1-2% and voltage reading is about... 0.004 and floating about 0.004 - 0.010 ....

Can I imagine an issue with pin A0 itself? I have about 10 Atmega spares :) and I will test another one... but thinking about this issue.

I did try also removing the 0.1uF cap, without any change.

The reading function is the same of this sketch.

Thank you very much!

[iahim67]

Hi guys, if your Arduino is equipped with an ATMega 328P then it could go down to 1.8V at lower frequencies like 1MHz (8MHz internal RC oscillator / 8 by default).
Or you can use the internal low power 128KHz RC osc eventually ...
It means you could power both the Arduino and the radio directly from the battery string and consume even less current.
Just wondering if anyone tried these cases so far?

[gohan]

There have been some users that went that way but personally I am preferring to use a single AA LiFePo4 battery with standard voltages and clocks

[MagnusF]

I am a newbie and have some thoughts about the battery level that I did not find in this forum.
The 8MHz 3.3V Arduino Pro Mini can handle down to roughly 2.8V.
If I have understood the calculations in the sketch correctly then the analog value of A0 is 1023 at 3.44V and 0 at 0V.
This means that at 2.8V the value is about 830 = 83% and under this, the Arduino stops working. Is this right?
If this is correct, I wonder if someone has changed the calculation in the sketch so that the battery percentage becomes 0 at 2.8V?
This would mean that the battery percentage becomes a more real value on the battery level.

[gohan]

It's a simple percentage calculation that you can do it in the code

[MagnusF]

@gohan Thanks for your reply, you can show me how the code should look.

[gohan]

void batM() //The battery calculations
{
  delay(500);
  // Battery monitoring reading
  int sensorValue = analogRead(BATTERY_SENSE_PIN);
  delay(500);

  // Calculate the battery in %
  float Vbat = sensorValue * VBAT_PER_BITS;
  send(msgVBat.set(Vbat, 3));
  int batteryPcnt = static_cast<int>(((Vbat - VMIN) / (VMAX - VMIN))*100.);
  Serial.print("Battery percent: "); Serial.print(batteryPcnt); Serial.println(" %");

  // Add it to array so we get an average of 3 (3x20min)
  batArray[batLoop] = batteryPcnt;

  if (batLoop > 2) {
    batteryPcnt = (batArray[0] + batArray[1] + batArray[2] + batArray[3]);
    batteryPcnt = batteryPcnt / 3;

    if (batteryPcnt > 100) {
      batteryPcnt = 100;
    }

    Serial.print("Battery Average (Send): "); Serial.print(batteryPcnt); Serial.println(" %");
    sendBatteryLevel(batteryPcnt);
    batLoop = 0;
  }
  else
  {
    batLoop++;
  }
}

This is the function I use, I just define the VMAX and VMIN in the beginning of sketch. The function calculates an average of 3 measurements before sending the value

[tonnerre33]

@gohan said in 💬 Battery Powered Sensors:
Hello, i didn't know why you add 4 measures (batarray) and you divide by 3 the sum .

[mfalkvidd]

@tonnerre33 good catch! maybe it's an optimistic value :)

[gohan]

I actually didn't look much at battery percentage, but I prefer looking at the voltage that gives me a better idea of how the battery is doing since I can log the values on a graph

[rozpruwacz]

@magnusf It is important to know that the battery voltage is non linear in respect to how much juice left. Just search for "battery discharge curve" to see how much it depends on battery type, current and temperature. So calculating the percentage is actually meaningless unless You exactly know how much current your board sucks at what temperature and what type of battery You use.

[Inso]

Instead of using "DC-DC Step Up Boost Module 5V" for a HBS, wouldn´t it make sense to just use 2 AA batteries for the nano and 2 additional batteries (i.e. four in a row) for the HBS?