💬 Building a Raspberry Pi Gateway

[OliverDog]

Why do Tx and Rx Leds blink every 5 to 6 seconds?

Is it about communication between RPi and Gateway?

Is there a way to disable it and keep blinks only with nodes communication?

[sineverba]

@sineverba said in 💬 Building a Raspberry Pi Gateway:

I have a couple of nodes + PI working without issues from a couple of days.
Now, I would add encryption / signing / security etc to protect traffic between Arduinos and PI.
Could you please help me posting right configuration to add to the

./configure

command?

Thank you very much!

Sorry..... I would UP! this :)

[Anticimex]

@sineverba is there not a --help argument to get a list of settings?

[sineverba]

@Anticimex sure... Bit I did read also the guide and .... I did noto understand very well whats I need to activate (if need) on gateway and on Arduinos to block, for example, the persone that live on third floor to play with my heater ..... :-) thank you in advance

PS security only software, no other hardware implied / want use

Thank you!

[Anticimex]

@sineverba I am not sure I understand what you want. You want to enable signing? There is extensive documentation on how to enable that. As for what to pass to the configure command on a rPi I am unsure of the exact naming but I am pretty sure the names are very similar to the #define:s the signing documentation describes.

[sineverba]

@Anticimex Yes, the doc is ... maybe ... too extensive :)

By the way, I would signing. So I need to do on both? Gateway/Raspberry and Arduino?

Thank you

[Anticimex]

@sineverba I am not sure I understand how it can be too excessive? It sounds like it is inadequate since you still have questions. :)
Of course you have to enable signing on both node and gateway. You also need to personalize the services with a hmac key. This is described. Please read the docs carefully. And if they are unclear, please provide a link to the documentation you have read, so I can verify you read the correct one.

[sineverba]

@Anticimex
I'm talking about this: https://www.mysensors.org/about/signing

Seems to me that probably need to be more clear your hint: you have to enable signing on both node and gateway.

I hope that soon I will can test on my network :)

Thank you for the moment :)

[Anticimex]

@sineverba yes, well that is for the official release so so far so good. I assume you also run the official version of the library and not the beta version, right?
For details on rPi configuration, perhaps @marceloaqno can provide some assistance but you will find all information needed on that page for configuring signing on your nodes.

[sineverba]

@Anticimex On Raspberry PI V1 I can work only with branch development. With master the radio / serial doesn't work

[Anticimex]

@sineverba then please use this documentation instead.

[sineverba]

@Anticimex thank you but... it is not the same?

[Anticimex]

@sineverba no, it isn't. There are newer features on beta branch. A third simplified option for signing exist (and if you have a hard time figuring out signing I highly recommend you use it).

[sineverba]

Raspberry PI V1 Model B (2 USB ports, no wifi, 26 GPIO).

RASPBIAN JESSIE LITE v 2017-04-10-raspbian-jessie-lite.

Some day ago I did compile the gateway only with development branch, using this:

./configure --my-transport=nrf24 --my-rf24-irq-pin=15 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB020

And all works fantastic.

Today I did try a new fresh installation for a friend, same PI, and same commands and routine from zero:

1. Logged with PI
2. Changed Password
3. Activate SSH
4. Activate SPI
5. Expand Filesystem
6. Changed timezone

launched

./configure --my-transport=nrf24 --my-rf24-irq-pin=15 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB020

No error on output, rebooted many times, gateways locked. See the screen:

With current setup (that works perfect), if I reconfigure to use Led TX/RX/Err, I get same lock.

I have SD and a copy of it, but I would setup another one from zero.... and I cannot.

Thank you

[sineverba]

I don't want give up!

I did download last RASPBIAN version (2017-06-21).
Gitted from development branch...

My question is.... is it a problem of my PI? Too old? Need to buy the V3?

I don't understand why some time ./configure works (and entire system with domoticz works without problem!!!) and other time no!

@sineverba said in 💬 Building a Raspberry Pi Gateway:

Raspberry PI V1 Model B (2 USB ports, no wifi, 26 GPIO).

RASPBIAN JESSIE LITE v 2017-04-10-raspbian-jessie-lite.

Some day ago I did compile the gateway only with development branch, using this:

./configure --my-transport=nrf24 --my-rf24-irq-pin=15 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB020

And all works fantastic.

Today I did try a new fresh installation for a friend, same PI, and same commands and routine from zero:

1. Logged with PI
2. Changed Password
3. Activate SSH
4. Activate SPI
5. Expand Filesystem
6. Changed timezone

launched

./configure --my-transport=nrf24 --my-rf24-irq-pin=15 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB020

No error on output, rebooted many times, gateways locked. See the screen:

With current setup (that works perfect), if I reconfigure to use Led TX/RX/Err, I get same lock.

I have SD and a copy of it, but I would setup another one from zero.... and I cannot.

Thank you

[sineverba]

Hi to all!
I did another test, on a new SD with Raspbian Lite 2017-06-21.

It doesn't work. Hangs on protocol version.

But... I did note this, after ./configure

Master branch

[SECTION] Detecting target machine.
  [OK] machine detected: SoC=unknown, Type=unknown, CPU=armv6l.
[SECTION] Checking GPIO Sysfs.
  [OK] /sys/class/gpio/export found
[SECTION] Detecting SPI driver.
  [OK] SPI driver detected:SPIDEV.
[SECTION] Detecting init system.
  [OK] init system detected: systemd.
[SECTION] Saving configuration.
[SECTION] Cleaning previous builds.
[OK] Finished.

Development branch

[SECTION] Detecting target machine.
  [OK] machine detected: SoC=BCM2835, Type=rpi1, CPU=armv6l.
[SECTION] Detecting SPI driver.
  [OK] SPI driver detected:BCM.
[SECTION] Detecting init system.
  [OK] init system detected: systemd.
[SECTION] Saving configuration.
[SECTION] Cleaning previous builds.
[OK] Finished.

I'm going crazy :(

@sineverba said in 💬 Building a Raspberry Pi Gateway:

I don't want give up!

I did download last RASPBIAN version (2017-06-21).
Gitted from development branch...

My question is.... is it a problem of my PI? Too old? Need to buy the V3?

I don't understand why some time ./configure works (and entire system with domoticz works without problem!!!) and other time no!

@sineverba said in 💬 Building a Raspberry Pi Gateway:

Raspberry PI V1 Model B (2 USB ports, no wifi, 26 GPIO).

RASPBIAN JESSIE LITE v 2017-04-10-raspbian-jessie-lite.

Some day ago I did compile the gateway only with development branch, using this:

./configure --my-transport=nrf24 --my-rf24-irq-pin=15 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB020

And all works fantastic.

Today I did try a new fresh installation for a friend, same PI, and same commands and routine from zero:

1. Logged with PI
2. Changed Password
3. Activate SSH
4. Activate SPI
5. Expand Filesystem
6. Changed timezone

launched

./configure --my-transport=nrf24 --my-rf24-irq-pin=15 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSB020

No error on output, rebooted many times, gateways locked. See the screen:

With current setup (that works perfect), if I reconfigure to use Led TX/RX/Err, I get same lock.

I have SD and a copy of it, but I would setup another one from zero.... and I cannot.

Thank you

[gohan]

Try DIETPI instead of raspian and see if it changes

[sineverba]

@gohan
I can and I will try, of sure. But, why do you think that something will change? My hardware is too old?

[skywatch]

Can you look and see what power supply you are using and also tell us what you have connected to the pi?
Do you have a volt meter and know how to use it?

[sineverba]

@skywatch
For a moment, I did hope that your was final solution.

By the way, I have HDMI attached (but TV is off) and a hub usb (with nothing attached).

I did try 7 sd cards.

I did try also Samsung charger (ETA U90EWE) and a powerbank, both 5v/2a

I have a cheap multimeter and I have basic knolewdge. What do you want I measure?

The radio is firmed soldered on an header array and linked with jumpers:

No caps 'cause the nodes and gw can transmit without problem on over 15 meters on my home :)

Exact configuration with a 7-days-old installation works very well. If I try to replicate, with every combination (last raspi/previous raspi/master/development) sometimes works, I re-flash and doesn't work anymore.

I'm not crazy, I would to be sure that in every moment I can replicate totally the configuration from scratch and... I want understand whats the problem!

PS The config that works very well, If I try to reconfigure to use the LEDS, after configure hangs on same, same step of debug. Luckily, I use rpi-clone before every single edit on my so-precious configuration.

PPS If someone wants, I could torrent my SD configured.... :(