💬 Atmospheric Pressure Sensor

[James Flosse]

i tested with 3.3V and 5volt but same result
http://www.banggood.com/fr/GY-68-BMP180-Digital-Barometric-Pressure-Sensor-Board-Module-p-1059025.html?rmmds=myorder

[ghislain]

OK, i've no further idea to help you. But i think your sensor is dead. DId you try older or newer library to compile your project ?

[James Flosse]

Have you link for older library? Are you french?

[ghislain]

I am and you ? I can give you the sketch which is working for me with library i used.

[James Flosse]

Yes ^^ . can you give me at snyp_thx at hotmail dot fr?

[bgunnarb]

Hi!
I had exactly the same problem until I realised I had compiled for the 8 MHz version of the Arduino Pro Mini instead of the 16 MHz version.
Also, recently building an humidity sensor I realised there are no pull-up resistors on the SDA SDL lines, but that should be built-in if you use a break-out module.

[Heinz]

Which altitude did you enter, or at which sealevel do you live (in meters)?

const float ALTITUDE = 688; // <-- adapt this value to your own location's altitude.

The pressure of 728 hPa is a bit strange as it should be around 1000 hPa. In my eyes you threw out the code to correct the pressure depending on the sealevel of your home. See the code from my sketch:

float pressure = bmp.seaLevelForAltitude(SEALEVEL, absolutePressure);

Here you can download the sketch I am using:
https://github.com/windkh/mysensors/blob/master/WeatherStationSensor/WeatherStationSensor.ino

The forecast will be unknown for at least 30minutes, because the sensor needs that time to detect a weather trend.

[James Flosse]

@bgunnarb you are find the problem, i think i have arduino pro mini 3.3V but it's 5V. Thx very much it's work better now :)

[Jeff Willecke]

Where do the pin assignments live?

[gohan]

@Jeff-Willecke
in the article page
SCL A5 (analog input) Marked blue
SDA A4 (analog input) Marked green

[Jeff Willecke]

@gohan it appears as though I need SLC and SDA for the sensor it will prevent me from using a second SLC/SDA device. I was assuming that they were utilizing the analog input. My comment may be deleted as it is clearly not applicable

[gohan]

that is I2C bus, you can collect multiple devices as long as they have different addresses

[Jeff Willecke]

OH cool. I guess I have tons more to learn thank you for your help

[skywatch]

The initial description on this page refers to BMP085.
The 'Example' states it is for BMP085 with Adafruit library (linked for dowbload).
The sketch uses a BME280 with library from Embedded Adventures.
The Datasheet is linked for a BMP085.
The shopping guide links to a BMP180.

????

[mfalkvidd]

Sorry for not noticing your post earlier @skywatch

The example was originally designed for BMP085. When the BMP180 became widely available, the buy link was updated to the newer version with the note "replaces the old BMP085". Both use the same library.

At a later stage, a MySensors user suggested changes to the example sketch to use the BME sensor instead. I don't know why this change was made, but my guess is that the user liked the BME sensor better. I don't know why the change was accepted without updating the build page, but my guess is that since the commit doesn't mention the change of sensor and the amount of code changed is quite large (369 additions and 252 deletions) nobody noticed that a new sensor was used.

I'm trying to address the sensor change in https://forum.mysensors.org/topic/9801/bmp-e-atmospheric-pressure

[Mark Hansen]

Heads-up: I've observed my sensor trying to sleep for 4 billion ms when running the sample code:

60082 MCO:SLP:MS=4294967214,SMS=0,I1=255,M1=255,I2=255,M2=255

That's 2^32-82. So I think there's an underflow with this line:

unsigned long sleeptime = BME280measurementSleepTime - (quicktimecheck - previousBME280Millis);

Not sure where exactly though. I've changed my code to simply sleep for a constant 60s.

[grumpazoid]

@mfalkvidd I've just started to look into this sensor and the main page is still quite confusing as already stated by @skywatch

It seems the choice at present is between the BMP280 or BME280. the latter also includes humidity.
Maybe the title could say Temperature/Pressure/Humidity? I just ordered a replacement Si7021, not realising there was another all in one sensor available.
It is clear that most ebay sellers are also confused and are wrongly listing BMP devices as BME.
I found a good summary to the confusion here https://goughlui.com/2018/08/05/note-bosch-sensortec-bmp280-vs-bme280-sensor-confusion/
Hope this helps someone - Think I'll be going for a BME280 here as it as some positive reviews https://www.ebay.co.uk/itm/Breakout-Temperature-Humidity-Barometric-Pressure-BME280-Digital-Sensor-Module/401513062540

[grumpazoid]

I have now had my delivery of the above ebay sensor. Everything looks good. It is a BME280 and reports temp, humidity and pressure.

I have used the sketch on the build page and it has worked without any editing. I just had to install the BME280 library as given in the example sketch. Everything is shown nicely in Domoticz.

Interesting to note that when compiling in arduino IDE I get the following error : Low memory available, stability problems may occur.

Wonder if there will be enough room to add my battery level monitoring code?

[mfalkvidd]

@grumpazoid If you don't use the forecast feature, remove #define GENERATE_FORECAST. Doing that should give you much less ram usage.

[grumpazoid]

@mfalkvidd Thanks for that. This is going to be my outside weather node running off a 12V solar charged battery. I started wi a DHT22 but it failed after a few months.