💬 Temperature Sensor

[Dick]

@mfalkvidd I chaned the Sleep into Wait but the same log in both Domoticz and on my Arduino. I thought it was an easy go but it appear not to be.

[rejoe2]

@Dick Did you change it at both places ( sleep(conversionTime);)?

[Dick]

@rejoe2 Yes on both location I replaced the sleep into a wait

[Dick]

@mfalkvidd In the Arduino log he Sleep error is not i anymore so that is solved but still no new device in Domoticz

[mfalkvidd]

@Dick if you get the same log on the Arduino as before changing to wait, the sketch upload must have failed. Perhaps your Arduino is broken?
Edit: Sorry, didn't see your last reply.

What does the node log say now?

[Dick]

@mfalkvidd Ths is what the log says
0 MCO:BGN:INIT REPEATER,CP=RNNRA--,VER=2.1.1
3 MCO:BGN:BFR
6 TSM:INIT
7 TSF:WUR:MS=0
14 TSM:INIT:TSP OK
16 TSF:SID:OK,ID=12
18 TSM:FPAR
59 TSF:MSG:SEND,12-12-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
1016 TSF:MSG:READ,0-0-12,s=255,c=3,t=8,pt=1,l=1,sg=0:0
1021 TSF:MSG:FPAR OK,ID=0,D=1
1804 TSF:MSG:READ,20-20-12,s=255,c=3,t=8,pt=1,l=1,sg=0:1
1851 TSF:MSG:READ,4-4-12,s=255,c=3,t=8,pt=1,l=1,sg=0:1
2067 TSM:FPAR:OK
2068 TSM:ID
2069 TSM:ID:OK
2071 TSM:UPL
2075 TSF:MSG:SEND,12-12-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2087 TSF:MSG:READ,0-0-12,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2093 TSF:MSG:PONG RECV,HP=1
2095 TSM:UPL:OK
2097 TSM:READY:ID=12,PAR=0,DIS=1
2102 TSF:MSG:SEND,12-12-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2111 TSF:MSG:READ,0-0-12,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2119 TSF:MSG:SEND,12-12-0-0,s=255,c=0,t=18,pt=0,l=5,sg=0,ft=0,st=OK:2.1.1
2128 TSF:MSG:SEND,12-12-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
2144 TSF:MSG:READ,0-0-12,s=255,c=3,t=6,pt=0,l=1,sg=0:M
2152 TSF:MSG:SEND,12-12-0-0,s=255,c=3,t=11,pt=0,l=18,sg=0,ft=0,st=OK:Temperature Sensor
2163 TSF:MSG:SEND,12-12-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.2
2169 MCO:REG:REQ
2173 TSF:MSG:SEND,12-12-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
2183 TSF:MSG:READ,0-0-12,s=255,c=3,t=27,pt=1,l=1,sg=0:1
2188 MCO:PIM:NODE REG=1
2190 MCO:BGN:STP
2192 MCO:BGN:INIT OK,TSP=1

[mfalkvidd]

@Dick thanks. The node still doesn't send any values so that's why it does not show up in Domoticz.

My next step would be to manually add serial debug prints at end of setup(), presentation(), and almost everywhere in loop(), to see why it doesn't attempt to send.

[rejoe2]

Very strange.
I just mad the test and copied the code (out of your post above) to my IDE, compiled and uploaded: No problem, worked fine. Node gets registered by FHEM, sends ID once and Temp regularly as expected. For testing, I used just one DS18B20, but that shouldn't make any difference. (And MySensors lib version 2.2-beta, but that also shouldn't be an issue).

Btw: what kind of a GW you are using?
Recently, I came across a situation with a WiFi-GW that absolutely refused to accept new nodes. Using a serial one, everything was fine... Strange thing, too. (The GW itself was ok, there were several other nodes working without any communication problems. the new HW was also ok. Last, the channel was also correct, as all the existing nodes just switched over to the serial GW.... Reflashing that nasty thing also was no solution.)

[Dick]

I put some deug lines i it and after uploadig the sketch it stops here (wait conversationtime.)
setup done.
2191 MCO:BGN:INIT OK,TSP=1
fetch sensors.
wait conversationtime.
fetch sensors.
wait conversationtime.
fetch sensors.
wait conversationtime.
fetch sensors.
wait conversationtime.
fetch sensors.
wait conversationtime.
fetch sensors.
wait conversationtime.
fetch sensors.
wait conversationtime.

[mfalkvidd]

@Dick could you try printing the value of numSensors in presentation()? (or in loop, it should have the same value there)

[Dick]

@mfalkvidd how can I manage that? sorr for the perhaps stupid qestion?

[mfalkvidd]

@Dick

Serial.print("Number of attached sensors found by the DallasTemperature library: ");
Serial.println(numSensors);

[rejoe2]

@Dick best place would be after numSensors = ... in presentation()

Just to mention that: The Arduino I used already had a node ID (I usually assign it manually). But your problem seems to be something completely different.

[Dick]

@mfalkvidd I tried it in Presentation() and in Loop() inboth no results in the log (copied it as you advised me how to do. so no result bisible). it is getting complex I think!
6 TSM:INIT
7 TSF:WUR:MS=0
14 TSM:INIT:TSP OK
16 TSF:SID:OK,ID=12
17 TSM:FPAR
59 TSF:MSG:SEND,12-12-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
452 TSF:MSG:READ,0-0-12,s=255,c=3,t=8,pt=1,l=1,sg=0:0
457 TSF:MSG:FPAR OK,ID=0,D=1
561 TSF:MSG:READ,20-20-12,s=255,c=3,t=8,pt=1,l=1,sg=0:1
2066 TSM:FPAR:OK
2067 TSM:ID
2068 TSM:ID:OK
2070 TSM:UPL
2074 TSF:MSG:SEND,12-12-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2086 TSF:MSG:READ,0-0-12,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2092 TSF:MSG:PONG RECV,HP=1
2094 TSM:UPL:OK
2096 TSM:READY:ID=12,PAR=0,DIS=1
2101 TSF:MSG:SEND,12-12-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2110 TSF:MSG:READ,0-0-12,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2118 TSF:MSG:SEND,12-12-0-0,s=255,c=0,t=18,pt=0,l=5,sg=0,ft=0,st=OK:2.1.1
2127 TSF:MSG:SEND,12-12-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
2142 TSF:MSG:READ,0-0-12,s=255,c=3,t=6,pt=0,l=1,sg=0:M
2151 TSF:MSG:SEND,12-12-0-0,s=255,c=3,t=11,pt=0,l=18,sg=0,ft=0,st=OK:Temperature Sensor
2161 TSF:MSG:SEND,12-12-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.2
2168 MCO:REG:REQ
2172 TSF:MSG:SEND,12-12-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
2181 TSF:MSG:READ,0-0-12,s=255,c=3,t=27,pt=1,l=1,sg=0:1
2186 MCO:PIM:NODE REG=1
2189 MCO:BGN:STP
setup done.
2190 MCO:BGN:INIT OK,TSP=1
fetch sensors.
wait conversationtime.
fetch sensors.
wait conversationtime.
fetch sensors.
wait conversationtime.

[rejoe2]

How are your sensors wired? Parasitic or 3 wires?
Sounds like a broken sensor, wrong wiring or a lot of sensors (to much for the pullup used).

[mfalkvidd]

Ok. I give up. If the node isn't executing the serial prints I know no way of troubleshooting.

[Dick]

@mfalkvidd I ony can tell "thanksfo the support ad you time" . Have a nice wekend!!!

[skywatch]

I have been frustrated with this for weeks now. Today I notice that void loop is not closed with a curly brace and if I add one it does not compile.
So what black magic is going on here?

I have been trying to get sensor readings every 2 mins and battery every half hour. But whatever I try it still gives temp every minute and battery at once a minute too. No wonder my batteries are draining so fast.

[mfalkvidd]

@skywatch the curly braces were discussed and explained earlier in this thread.

Could you post your sketch and the debug output of your node?

[skywatch]

@mfalkvidd

Thanks for fast reply! See code below. If you don't see problem there I will debug tomorrow. The battery time is set for 90sec to test, but is taking 18mins between sends!

// Enable debug prints to serial monitor
//#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69
#define COMPARE_TEMP 1 // Send temperature only if changed? 1 = Yes 0 = No
#define MY_RF24_PA_LEVEL (RF24_PA_LOW)
#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define MAX_ATTACHED_DS18B20 3
#include <SPI.h>
#include <MySensors.h>
#include <DallasTemperature.h>
#include <OneWire.h>
int BATTERY_SENSE_PIN = A0;  // select the input pin for the battery sense point
int batteryPcnt = 0;
unsigned long SLEEP_TIME = 117000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature.
float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors = 0;
const long interval = 90000;
unsigned long previousMillis = 0;
bool receivedConfig = false;
bool metric = true;
// Initialize temperature message
MyMessage msg(0, V_TEMP);

void before()
{
  // Startup up the OneWire library
  sensors.begin();
}

void setup()
{
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
  analogReference(INTERNAL);
}

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("HW/CH", "0.4");

  // Fetch the number of attached temperature sensors
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i = 0; i < numSensors && i < MAX_ATTACHED_DS18B20; i++) {
    present(i, S_TEMP);
  }
}

void loop()
{
  // get the battery Voltage
  unsigned long currentMillis = millis();

  if (currentMillis - previousMillis >= interval) {
    previousMillis = currentMillis;
    int sensorValue = analogRead(BATTERY_SENSE_PIN);
    batteryPcnt = sensorValue / 10;
    sendBatteryLevel(batteryPcnt);
  }

  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller
  for (int i = 0; i < numSensors && i < MAX_ATTACHED_DS18B20; i++) {

    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getControllerConfig().isMetric ? sensors.getTempCByIndex(i) : sensors.getTempFByIndex(i)) * 10.)) / 10.;

    // Only send data if temperature has changed and no error
#if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
#else
    if (temperature != -127.00 && temperature != 85.00) {
#endif

      // Send in the new temperature
      send(msg.setSensor(i).set(temperature, 1));
      // Save new temperatures for next compare
      lastTemperature[i] = temperature;
    }
  }

  int8_t sleep(1, FALLING, SLEEP_TIME);
}```