💬 Temperature Sensor

mfalkvidd

@skywatch could you post the entire sketch also, to check if something fishy has crept in?

skywatch

Here is the sketch, debug will be later today I hope....



// Enable debug prints to serial monitor
//#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69
#define COMPARE_TEMP 1 // Send temperature only if changed? 1 = Yes 0 = No
#define MY_RF24_PA_LEVEL (RF24_PA_LOW)
#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define MAX_ATTACHED_DS18B20 3
#include <SPI.h>
#include <MySensors.h>
#include <DallasTemperature.h>
#include <OneWire.h>
int BATTERY_SENSE_PIN = A0;  // select the input pin for the battery sense point
int batteryPcnt = 0;
unsigned long SLEEP_TIME = 2 * 60 * 1000; // 2 minutes Sleep time between reads.
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature.
float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors = 0;
const long interval = 90000;
unsigned long previousMillis = 0;
bool receivedConfig = false;
bool metric = true;
unsigned int batteryReportFactor = 30*60*1000/SLEEP_TIME; // Only report battery every x SLEEP times (x=15 with current values)
unsigned int timesSlept = 0;
// Initialize temperature message
MyMessage msg(0, V_TEMP);

void before()
{
  // Startup up the OneWire library
  sensors.begin();
}

void setup()
{
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
  analogReference(INTERNAL);
}

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("HW/CH", "0.5");

  // Fetch the number of attached temperature sensors
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i = 0; i < numSensors && i < MAX_ATTACHED_DS18B20; i++) {
    present(i, S_TEMP);
  }
}

void loop()
{
  // get the battery Voltage
  if (timesSlept < batteryReportFactor) {
    timesSlept++;
  } else {
    // get the battery Voltage
    timesSlept = 0;
    int sensorValue = analogRead(BATTERY_SENSE_PIN);
    batteryPcnt = sensorValue / 10;
    sendBatteryLevel(batteryPcnt);
  }

  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller
  for (int i = 0; i < numSensors && i < MAX_ATTACHED_DS18B20; i++) {

    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getControllerConfig().isMetric ? sensors.getTempCByIndex(i) : sensors.getTempFByIndex(i)) * 10.)) / 10.;

    // Only send data if temperature has changed and no error
#if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
#else
    if (temperature != -127.00 && temperature != 85.00) {
#endif

      // Send in the new temperature
      send(msg.setSensor(i).set(temperature, 1));
      // Save new temperatures for next compare
      lastTemperature[i] = temperature;
    }
  }

  int8_t sleep(1, FALLING, SLEEP_TIME);
}```

Thanks!

mfalkvidd

@skywatch code looks good to me. What type of Arduino are you using?

skywatch

I am using a pro mini 3.3v 8MHz. I would ideally like to get a 1MHZ bootloader onto it but the last try stopped the temperature sensors sending data (although battery levels were still sent!)..... Hope it helps.

mfalkvidd

@skywatch could you also print the return value of the sleep function. Maybe that interrupt is triggering it so it returns early?

skywatch

Sorry for the dealy, I have had a week of plumbing problems at home - yuck! :(

So, I came back fresh to this and noticed that I had put the interrupt into the code ready for the water leak sensor (apt considering this weeks activities!) - BUT, I had not assigned the pin nor initialised it in the code. So maybe it was floating and giving random triggers?
I tested by changing from int8_t sleep(1, FALLING, SLEEP_TIME); to int8_t sleep(SLEEP_TIME); but now I get battery level sent every single second! - This is making me crazy......

The log for the gateway has the following.....

Sep  3 07:00:37 HAAS rsyslogd-2007: action 'action 17' suspended, next retry is Sun Sep  3 07:02:07 2017 [try http://www.rsyslog.com/e/2007 ]
Sep  3 06:26:28 HAAS rsyslogd0: action 'action 17' resumed (module 'builtin:ompipe') [try http://www.rsyslog.com/e/0 ]
Sep  3 06:26:28 HAAS rsyslogd-2359: action 'action 17' resumed (module 'builtin:ompipe') [try http://www.rsyslog.com/e/2359 ]

Not sure what the above is all about. Nor the below....

7:15:45 HAAS dhcpcd[474]: eth0: Router Advertisement from fe80::3291:8fff:fe06:64bc

But here is sending data every second.....

Sep  3 12:46:52 HAAS mysgw: TSF:MSG:READ,5-5-0,s=255,c=3,t=0,pt=1,l=1,sg=0:75
Sep  3 12:46:53 HAAS mysgw: TSF:MSG:READ,5-5-0,s=255,c=3,t=0,pt=1,l=1,sg=0:75
Sep  3 12:46:54 HAAS mysgw: TSF:MSG:READ,5-5-0,s=255,c=3,t=0,pt=1,l=1,sg=0:75
Sep  3 12:46:55 HAAS mysgw: TSF:MSG:READ,5-5-0,s=255,c=3,t=0,pt=1,l=1,sg=0:75
Sep  3 12:46:56 HAAS mysgw: TSF:MSG:READ,5-5-0,s=255,c=3,t=0,pt=1,l=1,sg=0:75
Sep  3 12:46:57 HAAS mysgw: TSF:MSG:READ,5-5-0,s=255,c=3,t=0,pt=1,l=1,sg=0:75
Sep  3 12:46:58 HAAS mysgw: TSF:MSG:READ,5-5-0,s=255,c=3,t=0,pt=1,l=1,sg=0:75
Sep  3 12:46:59 HAAS mysgw: TSF:MSG:READ,5-5-0,s=255,c=3,t=0,pt=1,l=1,sg=0:75
Sep  3 12:47:00 HAAS mysgw: TSF:MSG:READ,5-5-0,s=255,c=3,t=0,pt=1,l=1,sg=0:75

Will try debug on node next....

skywatch

I.m sure it is a bug in 2.2.0-beta as I have the same issues with another node sending data whenever it changes and not sleeping.

dertho

Hi,

is there any known problem / bug with version 2.1.* and the Dallas temp sensor? (I found non in the bug tracker and/or forum)

I updated several nodes from 1.5 to 2.1.1 and now no temp sensor is working. No temp sensor DS18B20 is found by the node, therefore -127.0 is returned to the controller. I checked the wiring - as illustrated in this manual, everything seems right; incl. the pull-up with 4,7 k. I use the modified version of the Dallas-Library included in the examples package, as stated out in this manual.

Thanks,
Thomas

Mohammed Zaman

I am not a programmer, but trying to learn by making small projects.
I am trying to build a arduino/ESP8266 with temp sensor so that at a particular set temp it sends a single to another arduino/ESP8266 with relay to turn on a cooler/heater. if there is a thread on this, please help me find it.

rejoe2

@Mohammed-Zaman This seems to be possible, you may find more info wrt your topic using "node to node communication" as a keyword for searching the forum.
This might be a good starting point: https://forum.mysensors.org/topic/6386/almost-controller-less-mysensors-switch-light-network/8#

gohan

https://forum.mysensors.org/topic/7810/alternative-passive-mode if you don't want to use a gateway.

sjoerd14

regarding error:

C:\Users\Admin\Documents\Arduino\libraries\DallasTemperature/DallasTemperature.h:249:13: error: 'int16_t DallasTemperature::millisToWaitForConversion(uint8_t)' is private

In the latest version of Miles Burton's the function is public and compiling fine.
https://github.com/milesburton/Arduino-Temperature-Control-Library

You can import the Lib as zip.
You have to remove \ archive the lib: ...\libraries\DallasTemperature

mfalkvidd

@sjoerd14 yes, thanks to MySensors user David Ducatel. The change is tracked in https://github.com/mysensors/MySensorsArduinoExamples/issues/20 and https://github.com/milesburton/Arduino-Temperature-Control-Library/pull/72 but we're still waiting for an official release of milesburton's library.

nofox

Hi, I have few in wall nodes mounted under the light switches. I have two relays and one DS18B20 in each node. When i'm turning light on, switching the relay, the DS18B20 readings jumping about 0.8 degrees celsius up. When I switch off the relay readings back to normal. Anyone have similar problems ? Sensors are away from from node board, relays etc. so it's not about the heat from atmega or relays.

gohan

Is the temperature gradually rising after the relay is activated or it is instantly jumping 0.8°?

nofox

Jumping 0.8 immediately after switching the relay and sometimes rising very slow during the time when relay is on.

gohan

That makes it quite difficult to figure out the problem. Can you make another node with same setup and see if you get the same results and if you do try unplug the relay and see what happens

skywatch

It's probably a voltage drop from the psu when the relay is engaged and drawing current. That will cause the output voltage to dip slightly.

If it is only momentary you can add a beefy capacitor across the power supply, but if the readings change for the whole time the relay is on, you really need to replace the relay with something that uses less power (triac/mosfet??) - Or get a more stable power supply with good regulation.

A final thing might be more noise on the power line with the psu sending more current with the relay on. again a smoothing capacitor would help if this were the case.

You could also try looking into the wiring and see if the relay cables and the ds18b20 cables are far enough apart, some induction might be going on there between the cables. Also, make sure everything goes back to a single ground point. I can't imagine how an earth loop would cause what you describe, but it's always a good thing to do.....

Another thought to think about is matbe the magnetic field from the relap power cables are inducing into the sensor cables.

ben999

Hi
Can we talk about redundancy please? What if one or more sensor fail on a one-wire bus? Would it make the whole line unusable?
As part of a central heating MySensorization i would like to have groups of 3 sensors and have some sort of redundancy check.
Would i be allowed to run multiple one-wire busses on a single arduino?
Thanks a lot foryour help

mfalkvidd

@ben999 you can have as many onewire buses as you have digital pins. Just add more of these:

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
OneWire oneWire(ONE_WIRE_BUS);

💬 Temperature Sensor

10

11.7k

11.2k

113.0k