SerialGateway is rebooting on relay.

[delinend]

@hek
Yes. 100uF and a 10nF (parallel) on all Radio's.
I see no problem, when I send from Node(ID 6) to the SerialGateway.
And I see no problem when I send from Node(ID 6) via the SerialGateway to Node(ID 7).

The SerialGateway reboot's, if I turn OFF Node(ID 7) and the SerialGateway can't send to it.

[tekka]

@delinend Can you provide a full debug log of all involved nodes for both scenarios? This would help to investigate the issue further. Also, please indicate AVR board def version.

[delinend]

@tekka
Sure.. AVR Boards version 1.6.14

Here the SerialGateway:

0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.0.1-beta
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY
0;255;3;0;14;Gateway startup complete.
0;255;0;0;18;2.0.1-beta
0;255;3;0;9;MCO:REG:NOT NEEDED
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,ID=0,PAR=0,DIS=0,REG=1
0;255;3;0;9;TSF:MSG:READ,6-6-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;TSF:MSG:BC
0;255;3;0;9;TSF:MSG:FPAR REQ,ID=6
0;255;3;0;9;TSF:PNG:SEND,TO=0
0;255;3;0;9;TSF:CKU:OK
0;255;3;0;9;TSF:MSG:GWL OK
0;255;3;0;9;TSF:MSG:SEND,0-0-6-6,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
0;255;3;0;9;TSF:MSG:READ,6-6-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
0;255;3;0;9;TSF:MSG:PINGED,ID=6,HP=1
0;255;3;0;9;TSF:MSG:SEND,0-0-6-6,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
0;255;3;0;9;TSF:MSG:READ,6-6-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
0;255;3;0;9;TSF:MSG:SEND,0-0-6-6,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
0;255;3;0;9;TSF:MSG:READ,6-6-0,s=255,c=0,t=17,pt=0,l=10,sg=0:2.0.1-beta
6;255;0;0;17;2.0.1-beta
0;255;3;0;9;TSF:MSG:READ,6-6-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0
6;255;3;0;6;0
0;255;3;0;9;TSF:MSG:READ,6-6-0,s=255,c=3,t=11,pt=0,l=13,sg=0:Binary Sensor
6;255;3;0;11;Binary Sensor
0;255;3;0;9;TSF:MSG:READ,6-6-0,s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
6;255;3;0;12;1.0
0;255;3;0;9;TSF:MSG:READ,6-6-0,s=3,c=0,t=0,pt=0,l=0,sg=0:
6;3;0;0;0;
0;255;3;0;9;TSF:MSG:READ,6-6-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
0;255;3;0;9;TSF:MSG:SEND,0-0-6-6,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
0;255;3;0;9;TSF:MSG:READ,6-6-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
6;3;1;0;16;1
0;255;3;0;9;TSF:MSG:READ,6-6-7,s=3,c=1,t=16,pt=1,l=1,sg=0:1
0;255;3;0;9;TSF:MSG:REL MSG
0;255;3;0;9;!TSF:MSG:SEND,6-0-7-7,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=NACK:1
0;255;3;0;9;MCO:BGN:INIT GW,CP=RNNGA--,VER=2.0.1-beta
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSM:INIT:TSP OK
0;255;3;0;9;TSM:INIT:GW MODE
0;255;3;0;9;TSM:READY
0;255;3;0;14;Gateway startup complete.
0;255;0;0;18;2.0.1-beta
0;255;3;0;9;MCO:REG:NOT NEEDED
0;255;3;0;9;MCO:BGN:STP
0;255;3;0;9;MCO:BGN:INIT OK,ID=0,PAR=0,DIS=0,REG=1

Here Node(ID 6) that sends data to the SerialGateway, and Node(ID 7). The Node(ID 7) is turned OFF.:

0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.0.1-beta
4 TSM:INIT
10 TSM:INIT:TSP OK
12 TSM:INIT:STATID=6
14 TSF:SID:OK,ID=6
16 TSM:FPAR
53 TSF:MSG:SEND,6-6-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
137 TSF:MSG:READ,0-0-6,s=255,c=3,t=8,pt=1,l=1,sg=0:0
143 TSF:MSG:FPAR OK,ID=0,D=1
2062 TSM:FPAR:OK
2062 TSM:ID
2064 TSM:ID:OK
2066 TSM:UPL
2070 TSF:MSG:SEND,6-6-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2088 TSF:MSG:READ,0-0-6,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2095 TSF:MSG:PONG RECV,HP=1
2099 TSM:UPL:OK
2101 TSM:READY
2103 TSF:MSG:SEND,6-6-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2113 TSF:MSG:SEND,6-6-0-0,s=255,c=0,t=17,pt=0,l=10,sg=0,ft=0,st=OK:2.0.1-beta
2123 TSF:MSG:SEND,6-6-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
2131 TSF:MSG:READ,0-0-6,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
4134 TSF:MSG:SEND,6-6-0-0,s=255,c=3,t=11,pt=0,l=13,sg=0,ft=0,st=OK:Binary Sensor
4145 TSF:MSG:SEND,6-6-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
4153 TSF:MSG:SEND,6-6-0-0,s=3,c=0,t=0,pt=0,l=0,sg=0,ft=0,st=OK:
4161 MCO:REG:REQ
4165 TSF:MSG:SEND,6-6-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
4175 TSF:MSG:READ,0-0-6,s=255,c=3,t=27,pt=1,l=1,sg=0:1
4182 MCO:PIM:NODE REG=1
4184 MCO:BGN:STP
4186 MCO:BGN:INIT OK,ID=6,PAR=0,DIS=1,REG=1
4190 MCO:SLP:MS=5,SMS=0,I1=255,M1=255,I2=255,M2=255
4196 MCO:SLP:TPD
4198 MCO:SLP:WUP=-1
4202 TSF:MSG:SEND,6-6-0-0,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
4210 TSF:MSG:SEND,6-6-0-7,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=OK:1
4218 MCO:SLP:MS=0,SMS=0,I1=0,M1=1,I2=255,M2=255
4222 MCO:SLP:TPD

Btw. I have tryed to set all radio's to MIN power. But same result. If I turn ON Node(ID 7), everything works fine.

[tekka]

@delinend Ok, could you also enable MY_DEBUG_VERBOSE_RF24 in your GW, I need to see how far the message goes in the RF24 driver - I suspect a power issue.

[delinend]

@tekka
Hmm.. That is ode..
If I enable the MY_DEBUG_VERBOSE_RF24, the SerialGateway is NOT rebooting ?!?!

Here a snip from the LOG:

0;255;3;0;9;RF24:read register, reg=23, value=17
0;255;3;0;9;RF24:read register, reg=23, value=17
0;255;3;0;9;RF24:read register, reg=23, value=17
0;255;3;0;9;RF24:read register, reg=23, value=17
0;255;3;0;9;RF24:read register, reg=23, value=16
0;255;3;0;9;RF24:read message, len=8
0;255;3;0;9;RF24:write register, reg=7, value=64
0;255;3;0;9;TSF:MSG:READ,6-6-0,s=3,c=1,t=16,pt=1,l=1,sg=0:1
6;3;1;0;16;1
0;255;3;0;9;RF24:read register, reg=23, value=16
0;255;3;0;9;RF24:read message, len=8
0;255;3;0;9;RF24:write register, reg=7, value=64
0;255;3;0;9;TSF:MSG:READ,6-6-7,s=3,c=1,t=16,pt=1,l=1,sg=0:1
0;255;3;0;9;TSF:MSG:REL MSG
0;255;3;0;9;RF24:stop listening
0;255;3;0;9;RF24:write register, reg=0, value=14
0;255;3;0;9;RF24:open writing pipe, recipient=7
0;255;3;0;9;RF24:write register, reg=10, value=7
0;255;3;0;9;RF24:write register, reg=16, value=7
0;255;3;0;9;RF24:send message to 7, len=8
0;255;3;0;9;RF24:flushTX
0;255;3;0;9;RF24:write register, reg=7, value=48
0;255;3;0;9;RF24:MAX_RT
0;255;3;0;9;RF24:flushTX
0;255;3;0;9;RF24:start listening
0;255;3;0;9;RF24:write register, reg=0, value=15
0;255;3;0;9;RF24:write register, reg=10, value=0
0;255;3;0;9;!TSF:MSG:SEND,6-0-7-7,s=3,c=1,t=16,pt=1,l=1,sg=0,ft=0,st=NACK:1
0;255;3;0;9;RF24:read register, reg=23, value=17
0;255;3;0;9;RF24:read register, reg=23, value=17
0;255;3;0;9;RF24:read register, reg=23, value=17
0;255;3;0;9;RF24:read register, reg=23, value=17
0;255;3;0;9;RF24:read register, reg=23, value=17```

[tekka]

@delinend weird indeed. If you disable all debugs, how does it behave then?

[delinend]

@tekka
Her my codes...

Node(ID 6):

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_NRF24

#define MY_NODE_ID 6
//#define MY_DEFAULT_ERR_LED_PIN 4
#define MY_RF24_CHANNEL 101
#define MY_RF24_DATARATE RF24_250KBPS
#define MY_RF24_PA_LEVEL RF24_PA_MIN

//#define MY_PARENT_NODE_ID 0
//#define MY_TRANSPORT_DONT_CARE_MODE

#include <MySensors.h>

#define SKETCH_NAME "Binary Sensor"
#define SKETCH_MAJOR_VER "1"
#define SKETCH_MINOR_VER "0"

#define PRIMARY_CHILD_ID 3


#define PRIMARY_BUTTON_PIN 2   // Arduino Digital I/O pin for button/reed switch


// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(PRIMARY_CHILD_ID, V_TRIPPED);


void setup()
{
  // Setup the buttons
  pinMode(PRIMARY_BUTTON_PIN, INPUT);

}

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo(SKETCH_NAME, SKETCH_MAJOR_VER "." SKETCH_MINOR_VER);

  // Register binary input sensor to sensor_node (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage.
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  present(PRIMARY_CHILD_ID, S_DOOR);

}

// Loop will iterate on changes on the BUTTON_PINs
void loop()
{
  uint8_t value;
  static uint8_t sentValue=2;
  //static uint8_t sentValue2=2;

  // Short delay to allow buttons to properly settle
  sleep(5);

  value = digitalRead(PRIMARY_BUTTON_PIN);

  if (value != sentValue) {
     // Value has changed from last transmission, send the updated value
     send(msg.setDestination(0).set(value==HIGH));
     send(msg.setDestination(7).set(value==HIGH));
     
     sentValue = value;
  }



  // Sleep until something happens with the sensor
  sleep(PRIMARY_BUTTON_PIN-2, CHANGE, 0);
}

Here the SerialGateway code:

// Enable debug prints to serial monitor
#define MY_DEBUG
//#define MY_DEBUG_VERBOSE_RF24


// Enable and select radio type attached
#define MY_RADIO_NRF24

#define MY_RF24_CHANNEL 101
#define MY_RF24_DATARATE RF24_250KBPS
#define MY_RF24_PA_LEVEL RF24_PA_MIN


// Enable serial gateway
#define MY_GATEWAY_SERIAL

// Define a lower baud rate for Arduino's running on 8 MHz (Arduino Pro Mini 3.3V & SenseBender)
#if F_CPU == 8000000L
//#define MY_BAUD_RATE 38400
#endif

// Enable inclusion mode
#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE

// Inverses behavior of inclusion button (if using external pullup)
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP

// Set inclusion mode duration (in seconds)
#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN  3

// Set blinking period
#define MY_DEFAULT_LED_BLINK_PERIOD 300

// Inverses the behavior of leds
//#define MY_WITH_LEDS_BLINKING_INVERSE

// Flash leds on rx/tx/err
// Uncomment to override default HW configurations
//#define MY_DEFAULT_ERR_LED_PIN 4  // Error led pin
//#define MY_DEFAULT_RX_LED_PIN  6  // Receive led pin
//#define MY_DEFAULT_TX_LED_PIN  5  // the PCB, on board LED

#include <MySensors.h>

void setup() {
  // Setup locally attached sensors
}

void presentation() {
 // Present locally attached sensors
 
}

void loop() {
  delay(1);
}

void receive(const MyMessage &message) {
}

[delinend]

@tekka
And yes... If I remove the MY_DEBUG, it do NOT reboot !?!

So the SerialGateway reboot only, when I use the #define MY_DEBUG

Strange :-(

[tekka]

@delinend Yeah, and I assume if you downgrade your AVR board defs to 1.6.11 or .12, everything is fine?

[delinend]

@tekka
Hmmm Strange. It work fine with 1.6.11 ?!?

Why is there errors with 1.6.14 - 1.6.13 and 1.6.12 ?