How best to find the "best" small solar panel of a particular size?

[NeverDie]

@alexsh1 said in How best to find the "best" small solar panel of a particular size?:

@NeverDie Thanks for heads-up. I'll keep it in mind

I found an interesting cap -
https://www.digikey.co.uk/product-detail/en/vishay-bc-components/MAL219691204E3/4705PHBK-ND/5015889

Its voltage is very close to the solar panel so I think it may be connected directly via diode (0.7v drop = 6 - 0.7 = 5.3V vs 5.6V max rating)

I've tried that cap already, and I wouldn't recommend it. It has a fairly high ESR.

[alexsh1]

@NeverDie Given that you have been tinkering with it for a while, what caps can you recommend? With what ESR?

This cap has got 2.4 Ohm @ 1kHz - I think it is low?!

[NeverDie]

@alexsh1 said in How best to find the "best" small solar panel of a particular size?:

@NeverDie Given that you have been tinkering with it for a while, what caps can you recommend? With what ESR?

This cap has got 2.4 Ohm @ 1kHz - I think it is low?!

Perky explains it better than I can: https://lowpowerlab.com/forum/projects/a-solar-supercap-powered-moteino/msg18120/#msg18120

[NeverDie]

@ceech said in How best to find the "best" small solar panel of a particular size?:

TPS610986

1.5 mm x 1.5 mm WSON Package

Not sure how easy that will be to solder?

[alexsh1]

@NeverDie You need to get SMD rework station or oven.
This is extremely difficult to get done by even an iron with a fine tip.

[ceech]

@alexsh1 @NeverDie Yes, they will be soldered in the oven.

[NeverDie]

@ceech
Well, I may end up buying it from ceech then. Even properly aligning it onto the solder pads becomes difficult. I really struggled with the BQ25504. Not saying it can't be done, but just that it requires a lot more skill.

[alexsh1]

@NeverDie and a strong magnifying glass :-)

[ceech]

Those are the boards BTW

[alexsh1]

@ceech it is very small. Excellent. Let us know when it is ready

[ceech]

And if it is too tall, still, only two capacitors can be installed in horizontal position, or even just one.

[alexsh1]

@ceech How about a flat supercap like this:

https://www.digikey.co.uk/product-detail/en/vishay-bc-components/MAL219691252E3/4699PHBK-ND/5015883

There is no need to have two in my view unless you want to raise voltage. One flat to make the board compact may be enough.

[ceech]

Flat ones are nice. Nice package. High internal resistance, therefore low current. The double cell 15F flat capacitor can only supply 70mA.

[NeverDie]

This is great. :+1: Maybe more people will start playing with this stuff if they can buy inexpensive pre-made boards from ceech. The more, the merrier. :)

[alexsh1]

@ceech said iThe double cell 15F flat capacitor can only supply 70mA.

It should be enough if not using nrf24l01+ pa lna or rfm69HW. In this case perhaps, it would be better to have 150mA at least to cover those transmitters?
I like the size - It is really flat.

[NeverDie]

@alexsh1 said in How best to find the "best" small solar panel of a particular size?:

@ceech said iThe double cell 15F flat capacitor can only supply 70mA.

It should be enough if not using nrf24l01+ pa lna or rfm69HW. In this case perhaps, it would be better to have 150mA at least to cover those transmitters?
I like the size - It is really flat.

If you start to get choosy, that's when it's time to start making your own boards. It's easier than you might think. Otherwise, you just have to accept that the off-the-shelf stuff will never be exactly what you want.

It's really too bad there isn't more of a universal PCB format that's easily edited, so you can simply start with a board that's close to what you want and just customize it a bit (the way one might with, say, software). For instance, even just changing LDO's--unless the new LDO has exactly the same land pattern--can necessitate redoing the board. No problem if you're the original designer, but it's a PITA if you aren't.

[NeverDie]

I received the Chinese supercaps today. My "el cheapo" component tester is, I guess, too cheap, because it can't identify them:


So, if anyone has suggestions for a good capacitor tester, let me know.

However, I did plug the first one into my solar node after charging it ,and, so far it's not holding it's charge very well at all. I'll try the green one next.

[alexsh1]

@NeverDie I just watched this video:

https://youtu.be/EKRZEc-4SBo

Is this what you have been looking?

[NeverDie]

@alexsh1
I like Julien's videos, butI'd find something that's faster and more automated to be preferable, as well as something that can measure ESR too.

[NeverDie]

Well, so far the green supercap isn't holding its charge any better. I'll leave it in-circuit for two or three days, though, and see if that improves. It's encouraging that the rate of voltage decrease is decreasing. Some supercaps apparently improve their ability to retain charge if they are forced to hold a charge long enough, though I have no idea why that is. For instance, some capacitor leakage test protocols call for holding a capacitor at its rated voltage for 72 hours before running the leakage test.