NodeManager: plugin for a rapid development of battery-powered sensors

[mar.conte]

@user2684
It happens even if i put 6 hours or every 3 hours so in the specified hours it is not regular the report sometimes jumps some report

[user2684]

@mar.conte said in NodeManager: plugin for a rapid development of battery-powered sensors:

It happens even if i put 6 hours or every 3 hours so in the specified hours it is not regular the report sometimes jumps some report

Ok, I'd probably need both MySensors and NodeManagers's logs to troubleshoot this, just to ensure there is no failure in sending out the messages as I've seen in the other logs you have previously shared.

Thanks!

[mar.conte]

@user2684
Ok Tanks

[mar.conte]

Then solved the problem of the accuracy of the battery report: basically I did not realize that the sleep wait time started from the last pir movement then if i put an hour of sleep and during this active time the pir time resumes; The communication problems I solved them by letting antenna from rfm69 so every hour the battery report does not even send pir moviment
....Very strange my rfm69 modules communicate better without an antenna even at a distance of 10 meters with a wall

[gohan]

There is a risk of damaging the radio module if you don't use an antenna. Also a wrong tuned antenna will make transmitting more difficult.

[mar.conte]

@gohan
Ok Tanks, but the 86 mm wire for 868 what is Ideal diameter and thread type for simple antenna no dipole e non ground ant?

[gohan]

Found in another forum

433 1/4 wave = 164.7mm
433 1/2 wave = 329.4mm
433 full wave = 692.7mm

868 1/4 wave = 82.2mm
868 1/2 wave = 164.3mm
868 full wave = 345.5mm

915 1/4 wave = 77.9mm
915 1/2 wave = 155.9mm
915 full wave = 327.8mm

Try shortening a little bit. What kind of wire are you using?

[mar.conte]

@gohan
Wery good Tanks gohan

[mar.conte]

@gohan
Normal wire electric 1 mm diameter

[gohan]

Single core or threaded?

[mar.conte]

@gohan
Threaded

[gohan]

You need to use single core, that's why it is not working well

[mar.conte]

@gohan
Should it be isolated or even without a sheath?

[gohan]

I think you can leave insulation on; there are some guides on how to make antennas for rfm69,just Google it. In addition there are also spring single wire antennas for different frequencies you can buy.

[user2684]

@mar.conte said in NodeManager: plugin for a rapid development of battery-powered sensors:

I did not realize that the sleep wait time started from the last pir movement then if i put an hour of sleep and during this active time the pir time resumes

Yes, when the pir wakes the node up, the sleep is aborted and when going back to sleep, it starts from scratch without resuming it. If this is not creating an issue, I'll keep the current behavior. Regarding the antenna, I'm using the small antennas from the store for my RFM69 and have a decent range without big issues.

[mar.conte]

@user2684
Tanks of course bye

[bilbolodz]

I'm trying to build sensor to drive 3 relays and connect it to Domoticz. Simple sketch:

// before
void before() {
  // setup the serial port baud rate
  Serial.begin(MY_BAUD_RATE);  
  /*
   * Register below your sensors
  */
int przek1 = nodeManager.registerSensor(SENSOR_RELAY,3);
int przek2 = nodeManager.registerSensor(SENSOR_RELAY,4);
  /*
   * Register above your sensors
  */
  nodeManager.before();
}

sensors are visible into Domoticz as switches but It's not possible to turn it on/off from Domoticz. It looks that Nodemanager expect REQ message to change state of relay but Domoticz sends SET message to change state:

RECV S=0 I=3 C=1 T=2 D=1
RECV S=0 I=3 C=1 T=2 D=0

When I've used MYSController and send C_REQ message all is working fine.

I think that in case of "output" sensors logic of getting/setting should be reversed.

[user2684]

Hello, I think I was able to implement most of the requests discussed here during the last few weeks in a pre-release v1.5 version. Please consider it still as a dev release which gone through very limited testing but since I had to make quite a few changes to core code, would be great to start collecting some feedback now.

Is is available here: https://github.com/mysensors/NodeManager/tree/9a485cdcaf8e9856219338553335e2dce7253eb3

It is complicated to reference each of you who requested something so please whoever is interested the full list of new additions/fixes is available here https://github.com/mysensors/NodeManager/milestone/5?closed=1. I did my best to add verbose comments so you should find all the details there. Please add any comment and report any problem directly to the existing issues on github so I can better understand the context. The documentation has been updated as well.
Thanks

[mar.conte]

@user2684
👍🏾

[user2684]

I've just pushed out 1.5-dev3 on https://github.com/mysensors/NodeManager/tree/702a05c7e2f4425c188d5abf62b4a119fea29bc8 fixing a critical bug for the BME280 sensor and providing a way to automatically detect which i2c address the sensor is on for both BME280 and BMP085/BMP180 if anybody is interested.

I'm planning some additional tests so to release a stable v1.5 in a week or two (unfortunately starting from June the real life will become very demanding with me). So please share any feedback by then in case you will have the chance to test the latest dev release. Thanks