[SOLVED] OH2 - Mosquito - Raspi Mysensors Gateway

narf

Hello!
While i'm waiting for my hardware (ordered a couple Sensebender Micro) i tried to set up Controller and Gateway.
I followed the instructions from here here and configured with

./configure --my-gateway=mqtt --my-controller-ip-address=192.168.178.160 --my-mqtt-publish-topic-prefix=mysensors-out --my-mqtt-subscribe-topic-prefix=mysensors-in --my-mqtt-client-id=mygateway1

But the Gateway doesn't connect to the controller:

pi@raspgateway:~/MySensors $ sudo mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: Listening for connections on 0.0.0.0:5003
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
...

Then nothing more follows...

On openhabian (Raspberry) i installed the MQTT Binding (via OH2 paperUI) and Mosquitto (via openhabian config tool).
What am i missing? :/

Thanks in advance!
Narf!

narf

anybody? :(

Yveaux

@narf said in OH2 - Mosquito - Raspi Mysensors Gateway:

mysgw: Listening for connections on 0.0.0.0:5003

That doesn't seem to be right...
It seems it switches to listening (server) mode, while you are trying to configure an mqtt client connection. Myabe @marceloaqno has a clue?

gohan

Did you try to recompile the gateway?

narf

no - but i can try!
i'll just have to run

make

and

sudo make install

again, right?

narf

recompiling did the trick:

pi@raspgateway:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: Attempting MQTT connection...
mysgw: connected to 192.168.178.160
mysgw: MQTT connected
mysgw: Sending message on topic: mysensors-out/0/255/0/0/18

gohan

You probably compiled it before setting some parameters and with last build they were used. I'm glad you solved it.

narf

i'm a simple man, i do what the tutorials says =)
Thank you very much!

narf

alright! today (finally!) i got my sensebender micro. they should send something right away, right?
so i plugged one in and got this on the gateway:

pi@raspgateway:~/MySensors $ sudo ./bin/mysgw -d                                                                                  mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: Attempting MQTT connection...
mysgw: connected to 192.168.178.183
mysgw: MQTT connected
mysgw: Sending message on topic: mysensors-out/0/255/0/0/18
mysgw: TSF:MSG:READ,255-255-255,s=255,c=7,t=255,pt=7,l=25,sg=1: 0
mysgw: !TSF:MSG:LEN,7!=32
mysgw: TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
mysgw: Sending message on topic: mysensors-out/255/255/3/0/3
mysgw: TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,255-255-255,s=255,c=7,t=255,pt=7,l=25,sg=1: 0
mysgw: !TSF:MSG:LEN,7!=32

does this mean anything? i don't get it at all...

hek

Something is not quite right... See parsed log.

Message length seems to be a bit off and command type=7 ?? Doesn't make any sense.

narf

what's next? i tried to upload the sensebender micro sketch (couldn't find it in the lib) but had several errors. couldn't find a beginner-beginner tutorial on how to upload a first sketch.
Generally this output points to an error with gateway or with sensor?

hek

You must add the micro to your board manager first. Instructions here:
https://github.com/mysensors/ArduinoBoards

The Sensebender Micro sketch is available here:
https://github.com/mysensors/SensebenderMicro/tree/master/Arduino/SensebenderMicro

Did you decoupling capacitor on gateway? Do you have more radios to test with in the case one is broken?

narf

i found the board but i don't get how to load the sketch ON the board :/
first thought was to c&p the code from https://github.com/mysensors/SensebenderMicro/tree/master/Arduino/SensebenderMicro

fatal error: SI7021.h: No such file or directory

second thought was to look for an example sketch. no luck.

i have other radios. but i'd really love to upload the (right) sketch first... just... how?

@hek said in [SOLVED] OH2 - Mosquito - Raspi Mysensors Gateway:

Did you decoupling capacitor on gateway? Do you have more radios to test with in the case one is broken?

did i what exactly?
all i can say that i wired the gateway with one of the specified NRF24L01+ Radios.
Same radio on sensebender.

gohan

you need to install library for SI7021

narf

@gohan said in [SOLVED] OH2 - Mosquito - Raspi Mysensors Gateway:

you need to install library for SI7021

took libraries from here: https://github.com/mysensors/MySensorsArduinoExamples
will investigate further.

i think i got the sensor up and running and it can't find a gateway?

debug

gohan

In Arduino ide open library manager and search for that library or manually download it and choose to install new library as zip file.
For debug you posted it looks the node it is missing the node ID

narf

ok, thought this would be auto assigned: "Define a static node address, remove if you want auto address assignment"
new debug: everything ok with this sensor?
debug

Next Stop Gateway? Should i just try another radio?

gohan

Auto assign works if everything else is working and you have a controller that is able to assign node id.
Now it seems there is no communication with gateway: do you also have a log for the gateway? Did you put capacitors on the vcc/gnd on both gateway and node? Keep in mind that RPI is not very suited to power the nrf24 radio.

narf

the gateway "log" is some posts above.

pi@raspgateway:~/MySensors $ sudo ./bin/mysgw -d                                                                                  mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: Attempting MQTT connection...
mysgw: connected to 192.168.178.183
mysgw: MQTT connected
mysgw: Sending message on topic: mysensors-out/0/255/0/0/18
mysgw: TSF:MSG:READ,255-255-255,s=255,c=7,t=255,pt=7,l=25,sg=1: 0
mysgw: !TSF:MSG:LEN,7!=32
mysgw: TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
mysgw: Sending message on topic: mysensors-out/255/255/3/0/3
mysgw: TSF:MSG:READ,255-255-0,s=255,c=3,t=3,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,255-255-255,s=255,c=7,t=255,pt=7,l=25,sg=1: 0

should i provide another log?

i didn't use any capacitors, neither gateway, nor node.
here isn't anything regarding capacitors.
and [here](lhttps://www.mysensors.org/build/raspberry under section "NRF24L01+ Radio" it only says "If you are using the nrf24 PA/LNA version you need to use a 5V->3.3V regulator.", but i'm using these so i thought it's ok without using regulators.
or is a regulator something different than a capacitor?

gohan

Voltage regulator is OK but you need a capacitor 4.7uF or bigger on vcc/gnd of radio module. Those modules are probably the same as I bought 4 months ago and they are cheap clones and don't have good range but they work with the proper capacitor.

[SOLVED] OH2 - Mosquito - Raspi Mysensors Gateway

25

11.7k

11.2k

113.1k