Pro Mini + RFM node and ESP8266 + RFM gateway not working

[mpp]

So I connected the radio to the ESP and the Pro Mini as described.

Installed the DHT sketch on the Pro Mini and added:

#define MY_RADIO_RFM69
#define MY_RFM69_FREQUENCY RF69_433MHZ
#define MY_IS_RFM69HW
#define MY_RFM69_NETWORKID 99

The Serial output:

TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,Starting sensor (RRNNA-, 2.0.0)
TSM:INIT
TSM:RADIO:OK
TSM:FPAR
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
!TSM:FPAR:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
TSM:RADIO:OK
TSM:FPAR
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
TSM:FPAR
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:
!TSM:FPAR:FAIL
!TSM:FAILURE
TSM:PDT
TSM:INIT
TSM:RADIO:OK
TSM:FPAR
TSP:MSG:SEND 255-255-255-255 s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=bc:

Installed the default ESP MQTT gateway sketch on the ESP and added:

#define MY_RADIO_RFM69
#define MY_RFM69_FREQUENCY RF69_433MHZ
#define MY_IS_RFM69HW
#define MY_RF69_IRQ_PIN D1
#define MY_RF69_IRQ_NUM MY_RF69_IRQ_PIN
#define MY_RF69_SPI_CS D8
#define MY_RFM69_NETWORKID 99

The serial output:

K⸮⸮q⸮⸮0;255;3;0;9;Starting gateway (RRNGE-, 2.0.0)
0;255;3;0;9;TSM:INIT
0;255;3;0;9;TSM:RADIO:OK
0;255;3;0;9;TSM:GW MODE
0;255;3;0;9;TSM:READY
scandone
state: 0 -> 2 (b0)
f 0, state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 3
cnt 
scandone

connected with MPPort, channel 6
dhcp client start...
.............ip:192.168.0.219,mask:255.255.255.0,gw:192.168.0.1
.IP: 192.168.0.219
0;255;3;0;9;No registration required
0;255;3;0;9;Init complete, id=0, parent=0, distance=0, registration=1
IP: 192.168.0.219
0;255;3;0;9;Attempting MQTT connection...
0;255;3;0;9;MQTT connected
pm open,type:2 0
0;255;3;0;9;TSP:SANCHK:OK
0;255;3;0;9;TSP:SANCHK:OK
0;255;3;0;9;TSP:SANCHK:OK
0;255;3;0;9;TSP:SANCHK:OK
0;255;3;0;9;TSP:SANCHK:OK
0;255;3;0;9;TSP:SANCHK:OK

I'm seeing the initial message in mqtt but not the messages from the node: mygateway1-out/0/255/0/0/18 2.1.1

Any idea what could be going wrong?

[gohan]

#define MY_RFM69_NETWORKID 99set your preferred network id if needed

You forgot to leave the // after the 99 and I think it can cause some problems

[mpp]

@gohan thanks for the reply but that was just a typo. The sketch compiles and uploads properly. Yet I keep seeing connections to my Wifi when I upload the ping pong script for example, this doesn't seem to be normal.

[mpp]

The problems seem to have been caused by a bad connection on D1.

Still I find it strange that a Wifi login appears on the serial interface after programming the pingpong sketch.

[mfalkvidd]

@mpp the esp stores (in a special area of the eeprom) ssid and key for the accesspoint it last connected to, and automatically connects back next time unless wifi is turned off in the sketch.