Combining relay and temperature sketch

gohan

I probably used wrong sintax

Tim76

@gohan tried this again...... same result.....


  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=17; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);
    // Set relay to last known state (using eeprom storage)
    digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
  }
}

Tim76

here's the complete code as she is right now...


// Enable debug prints to serial monitor
#define MY_DEBUG 
#define MY_RF24_CE_PIN 49
#define MY_RF24_CS_PIN 53
// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69
#define MY_NODE_ID 30

#include <SPI.h>
#include <MySensors.h>  
#include <DallasTemperature.h>
#include <OneWire.h>



#define COMPARE_TEMP 1 // Send temperature only if changed? 1 = Yes 0 = No

#define ONE_WIRE_BUS 3 // Pin where dallase sensor is connected 
#define MAX_ATTACHED_DS18B20 16
OneWire oneWire(ONE_WIRE_BUS); // Setup a oneWire instance to communicate with any OneWire devices (not just Maxim/Dallas temperature ICs)
DallasTemperature sensors(&oneWire); // Pass the oneWire reference to Dallas Temperature. 
float lastTemperature[MAX_ATTACHED_DS18B20];
int numSensors=0;
bool receivedConfig = false;
bool metric = true;
// Initialize temperature message
MyMessage msgTemp(0,V_TEMP);


#define RELAY_1  30  // Arduino Digital I/O pin number for first relay (second on pin+1 etc)
#define NUMBER_OF_RELAYS 16 // Total number of attached relays
#define RELAY_ON 0  // GPIO value to write to turn on attached relay
#define RELAY_OFF 1 // GPIO value to write to turn off attached relay

void before()
{
  // Startup up the OneWire library
  sensors.begin();
}

void setup()  
{ 
  // requestTemperatures() will not block current thread
  sensors.setWaitForConversion(false);
}

void presentation() {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Greenhouse main controller", "1.0");

  // Fetch the number of attached temperature sensors  
  numSensors = sensors.getDeviceCount();

  // Present all sensors to controller
  for (int i=17; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);
    // Set relay to last known state (using eeprom storage)
    digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
  }
}

void loop()     
{     
  // Fetch temperatures from Dallas sensors
  sensors.requestTemperatures();

  // query conversion time and sleep until conversion completed
  int16_t conversionTime = sensors.millisToWaitForConversion(sensors.getResolution());
  // sleep() call can be replaced by wait() call if node need to process incoming messages (or if node is repeater)
  sleep(conversionTime);

  // Read temperatures and send them to controller 
  for (int i=0; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {

    // Fetch and round temperature to one decimal
    float temperature = static_cast<float>(static_cast<int>((getControllerConfig().isMetric?sensors.getTempCByIndex(i):sensors.getTempFByIndex(i)) * 10.)) / 10.;

    // Only send data if temperature has changed and no error
    #if COMPARE_TEMP == 1
    if (lastTemperature[i] != temperature && temperature != -127.00 && temperature != 85.00) {
    #else
    if (temperature != -127.00 && temperature != 85.00) {
    #endif

      // Send in the new temperature
      send(msgTemp.setSensor(i).set(temperature,1));
      // Save new temperatures for next compare
      lastTemperature[i]=temperature;
    }
  }
  wait(3000);
  }
  void receive(const MyMessage &message)
{
  // We only expect one type of message from controller. But we better check anyway.
  if (message.type==V_STATUS) {
    // Change relay state
    digitalWrite(message.sensor-1+RELAY_1, message.getBool()?RELAY_ON:RELAY_OFF);
    // Store state in eeprom
    saveState(message.sensor, message.getBool());
    // Write some debug info
    Serial.print("Incoming change for sensor:");
    Serial.print(message.sensor);
    Serial.print(", New status: ");
    Serial.println(message.getBool());
  }
}```

gohan

@Tim76 you forgot to present the relays.... :sweat:

Tim76

@gohan no I didn't...

  // Present all sensors to controller
  for (int i=17; i<numSensors && i<MAX_ATTACHED_DS18B20; i++) {   
     present(i, S_TEMP);
  }
  for (int sensor=1, pin=RELAY_1; sensor<=NUMBER_OF_RELAYS; sensor++, pin++) {
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);
    // Set relay to last known state (using eeprom storage)
    digitalWrite(pin, loadState(sensor)?RELAY_ON:RELAY_OFF);
  }
}```

Tim76

@gohan seems like it's early for both of us.....;-)

gohan

you only have present(i, S_TEMP) but you also need to add present(sensor, S_BINARY) in the relay section otherwise you will not present any relay at all.

Tim76

@gohan 😳😳😳 seems like it's only early for one of us...... I,ll change it later today.....

Tim76

@gohan so I fixed that....... and now I get this in Domoticz....

0 Unknown! #1. V_TEMP (20.7) true 2017-05-10 11:44:39
1 S_LIGHT/S_BINARY #1. V_TEMP (20.7) true 2017-05-10 11:44:43
2 S_LIGHT/S_BINARY #1. V_TEMP (20.9) true 2017-05-10 11:44:04
3 S_LIGHT/S_BINARY true 2017-05-10 11:34:13
4 S_LIGHT/S_BINARY true 2017-05-10 11:34:14
5 S_LIGHT/S_BINARY true 2017-05-10 11:34:15
6 S_LIGHT/S_BINARY true 2017-05-10 11:34:15
7 S_LIGHT/S_BINARY true 2017-05-10 11:34:16
8 S_LIGHT/S_BINARY true 2017-05-10 11:34:17
9 S_LIGHT/S_BINARY true 2017-05-10 11:34:17
10 S_LIGHT/S_BINARY true 2017-05-10 11:34:18
11 S_LIGHT/S_BINARY true 2017-05-10 11:34:18
12 S_LIGHT/S_BINARY true 2017-05-10 11:34:19
13 S_LIGHT/S_BINARY true 2017-05-10 11:34:19
14 S_LIGHT/S_BINARY true 2017-05-10 11:34:20
15 S_LIGHT/S_BINARY true 2017-05-10 11:34:20
16 S_LIGHT/S_BINARY true 2017-05-10 11:34:21
17 S_TEMP true 2017-05-10 11:34:12
18 S_TEMP true 2017-05-10 11:34:12
255 S_ARDUINO_NODE 2.1.1 false 2017-05-10 11:34:12

so it seems I do get temp Id's from 17 to 32, but the values stay in 0,1,2 where the relays 1 and 2 don't work.....

gohan

There must be a bug in the relay section, I can't check it today, I'm out all day.
Try to add some debug serial print to see what values are being exchanged

Tim76

@gohan output of the serial port

0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
3 MCO:BGN:BFR
144 TSM:INIT
145 TSF:WUR:MS=0
153 TSM:INIT:TSP OK
154 TSM:INIT:STATID=51
157 TSF:SID:OK,ID=51
158 TSM:FPAR
195 TSF:MSG:SEND,51-51-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
986 TSF:MSG:READ,0-0-51,s=255,c=3,t=8,pt=1,l=1,sg=0:0
990 TSF:MSG:FPAR OK,ID=0,D=1
2202 TSM:FPAR:OK
2203 TSM:ID
2204 TSM:ID:OK
2206 TSM:UPL
2211 TSF:MSG:SEND,51-51-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
2232 TSF:MSG:READ,0-0-51,s=255,c=3,t=25,pt=1,l=1,sg=0:1
2237 TSF:MSG:PONG RECV,HP=1
2240 TSM:UPL:OK
2241 TSM:READY:ID=51,PAR=0,DIS=1
2246 TSF:MSG:SEND,51-51-0-0,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
2284 TSF:MSG:READ,0-0-51,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
2291 TSF:MSG:SEND,51-51-0-0,s=255,c=0,t=17,pt=0,l=5,sg=0,ft=0,st=OK:2.1.1
2301 TSF:MSG:SEND,51-51-0-0,s=255,c=3,t=6,pt=1,l=1,sg=0,ft=0,st=OK:0
4329 TSF:MSG:SEND,51-51-0-0,s=255,c=3,t=11,pt=0,l=25,sg=0,ft=0,st=OK:Greenhouse main controlle
4340 TSF:MSG:SEND,51-51-0-0,s=255,c=3,t=12,pt=0,l=3,sg=0,ft=0,st=OK:1.0
4350 TSF:MSG:SEND,51-51-0-0,s=17,c=0,t=6,pt=0,l=0,sg=0,ft=0,st=OK:
4359 TSF:MSG:SEND,51-51-0-0,s=18,c=0,t=6,pt=0,l=0,sg=0,ft=0,st=OK:
4369 TSF:MSG:SEND,51-51-0-0,s=1,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4376 TSF:MSG:SEND,51-51-0-0,s=2,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4384 TSF:MSG:SEND,51-51-0-0,s=3,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4397 TSF:MSG:SEND,51-51-0-0,s=4,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4407 TSF:MSG:SEND,51-51-0-0,s=5,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4418 TSF:MSG:SEND,51-51-0-0,s=6,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4434 TSF:MSG:SEND,51-51-0-0,s=7,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4449 TSF:MSG:SEND,51-51-0-0,s=8,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4459 TSF:MSG:SEND,51-51-0-0,s=9,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4489 TSF:MSG:SEND,51-51-0-0,s=10,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4505 TSF:MSG:SEND,51-51-0-0,s=11,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4515 TSF:MSG:SEND,51-51-0-0,s=12,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4528 TSF:MSG:SEND,51-51-0-0,s=13,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4540 TSF:MSG:SEND,51-51-0-0,s=14,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4556 TSF:MSG:SEND,51-51-0-0,s=15,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4564 TSF:MSG:SEND,51-51-0-0,s=16,c=0,t=3,pt=0,l=0,sg=0,ft=0,st=OK:
4571 MCO:REG:REQ
4576 TSF:MSG:SEND,51-51-0-0,s=255,c=3,t=26,pt=1,l=1,sg=0,ft=0,st=OK:2
4583 TSF:MSG:READ,0-0-51,s=255,c=3,t=27,pt=1,l=1,sg=0:1
4588 MCO:PIM:NODE REG=1
4590 MCO:BGN:STP
4591 MCO:BGN:INIT OK,TSP=1
4596 MCO:SLP:MS=750,SMS=0,I1=255,M1=255,I2=255,M2=255
4601 MCO:SLP:TPD
4602 MCO:SLP:WUP=-1
4636 TSF:MSG:SEND,51-51-0-0,s=0,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:20.2
4690 TSF:MSG:SEND,51-51-0-0,s=1,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:20.5
4755 TSF:MSG:SEND,51-51-0-0,s=2,c=1,t=0,pt=7,l=5,sg=0,ft=0,st=OK:20.4
7763 MCO:SLP:MS=750,SMS=0,I1=255,M1=255,I2=255,M2=255
7768 MCO:SLP:TPD
7770 MCO:SLP:WUP=-1
10898 MCO:SLP:MS=750,SMS=0,I1=255,M1=255,I2=255,M2=255
10902 MCO:SLP:TPD
10904 MCO:SLP:WUP=-1

gohan

I'm talking about adding code to your sketch so that it prints in serial monitor the values before they are sent for presentations and you debug from those, I can't debug it for you from here 😀

Tim76

@gohan oh.... ok..... pretty new at coding, but I guess you allready figured that out.....;-)

gohan

No problem, it's normal, everybody started from being new at coding.
For debugging add only 1 or 2 temp sensors and same for relays, work it out simple and then add more

Tim76

@gohan hey Gohan,
I will not be able to continue to work on my code till after the weekend....😑

gohan

No problem, I'm here anyway 😀

Tim76

@gohan
Due to work related schedule problems I won't be able to work on this code for a few weeks...... :angry:

Newzwaver

Did you get this working and if so can you share?

bluezr1

@newzwaver I'm curious aswell, been pounding my head all night trying to get a temperature and relay into one sketch.

Newzwaver

HI

I did get it to work and will post the sketch later today after work. I have it working on the ESP8266 and Arduino.

Combining relay and temperature sketch

17

11.7k

11.2k

113.1k