Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 MySensors Easy Pro Mini

openhardware.io last edited by openhardware.io

https://www.openhardware.io/view/410/MySensors-Easy-Pro-Mini
Reply Quote 1
1 Reply Last reply
scalz Hardware Contributor last edited by

@Koresh nice design as usual
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by

Since it's not wireless, how do you envision this being used?
Reply Quote 0
1 Reply Last reply
sundberg84 Hardware Contributor last edited by sundberg84 @NeverDie

@NeverDie - You could att it to a https://www.openhardware.io/view/4/EasyNewbie-PCB-for-MySensors and get all the benefits from both. I like that it includes ATSHA204A.
Reply Quote 0
1 Reply Last reply
Koresh Contest Winner last edited by

First version of this board does not contain mistakes and works properly. I will remove "work in progress" mark after some tests soon.
Reply Quote 1
1 Reply Last reply
mfalkvidd Mod last edited by @Koresh

@Koresh very nice. Do you plan to sell these assembled? If so, is there an estimated price point?
Reply Quote 0
1 Reply Last reply
terxw last edited by

Hello, can you post BOM please,
according to schematics tantalum schould be 100uF bat tantalum cap in picture is 4.7uF
Reply Quote 0
1 Reply Last reply

mysensors 192 contest2017 35 atsha204a 28 ota 16

7
Posts

2737
Views

Log in to reply

Suggested Topics

💬 Window Sensor with Sensebender (high WAF)
OpenHardware.io • mysensors nrf24l01 door window waf • • openhardware.io

6

3
Votes

6
Posts

2211
Views

@antonholmstedt a pro mini fits if you cut the corners, check out https://forum.mysensors.org/topic/6612/door-sensor-remix-of-some-mys-community-efforts
ESP8266 gateway crashes while the node is in FOTA progress.
Troubleshooting • mqtt rfm69 esp8266 ota • • Abdu Sahin

6

0
Votes

6
Posts

1735
Views

After upgrading Wemos from 2.3.0 to 2.4.0-RC2 version, OTA works well know
💬 Battery powered glass touch switch
OpenHardware.io • mysensors contest2017 switch waf remote • • openhardware.io

21

0
Votes

21
Posts

6860
Views

@Nca78 Do you tested this board, if yes, did it work? And which CS capacitors did you use?
💬 Dual Channel 0-10V Dimmer
OpenHardware.io • mysensors dimmer 0-10v • • openhardware.io

2

0
Votes

2
Posts

990
Views

Hi Mardah, how this the progress on this project related to the software and testing? kind regards
💬 MySensors InCan double light switch
OpenHardware.io • mysensors nrf24l01 relay switch light hlk-pm01 acdc in-wall • • openhardware.io

24

1
Votes

24
Posts

2445
Views

The author has done some good work ensuring good design practices; trace separation, fuses, etc. but I don't see any extra I/O brought out on this particularl switch. You would have to carefully solder to the chip itself, and modify the code a bit. You could use magnetic switches. Put a magnet on the blinds and the switch in window sill. The author notes that this is not an Arduino, but uses the same chip that the Arduino uses. The author doesn't explain how the chip is programmed. This method could have been used. It may be just as easy to use an RF Nano with a little power supply. This suggestion is not nearly as robust as the author's. For example, these power supplies have gotten bad reviews mainly because the mains power traces are too close together. I justify using them because in all likelihood a failure will pop the power supply and probably the Nano, too, noting that these are cheaper than the fuses you would put in to protect them. I am fully aware of the risks involved in doing this, and you should be, too (eg. burning down your house). -OSD
💬 MySensors RS-485 Universal Module
OpenHardware.io • mysensors sensor rs485 button 485 wall plate • • openhardware.io

5

0
Votes

5
Posts

43
Views

@YuryPol as far as I know, all licenses require some form of documentation. In all cases I know of, this is documented with the license or on the licenses official site.
Washing machine and Tumbler Alarm
OpenHardware.io • mysensors contest2016 • • openhardware.io

1

2
Votes

1
Posts

1224
Views

No one has replied
Solar powered sensor board
OpenHardware.io • mysensors board • • openhardware.io

7

1
Votes

7
Posts

2988
Views

@Yveaux Thanks for your response. I guess that's it. I have to burn a bootloader first :-). I have a USBasp Programmer for that. Can you point me to a wiring diagram that shows how to connect the programmer to the circuit board?

404
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1