nRF5 action!

[korttoma]

@mika :+1:

Now I feel stupid ordering the NRF52 DK for 28€. Well atleast I don't need to worry about bricking any devices.
Do you have an example sketch for the device you can share?
Is it possible to somehow monitor the battery status?

[NeverDie]

@korttoma said in nRF5 Bluetooth action!:

Is it possible to somehow monitor the battery status?

One of @d00616 's demo sketches allows you to read the voltage that's powering the nRF5. Assuming there is no booster involved on this device (seems unlikely), that would be the same as the battery voltage.

[Toyman]

@korttoma do you have an Aliexpress link to them?

[korttoma]

@toyman sure do LINK

[Toyman]

@korttoma thx. Do they have a CR2032 slot? Sorry, it's not clear from the pictures

[korttoma]

@toyman yes

[NeverDie]

It would probably do well as a "one button scene controller," but is it good for anything else I wonder?

[korttoma]

@neverdie does not seem to be any easy way to get access to any of the pins on the board but who does not need a bunch of "one button scene controllers"?

[Nca78]

I was tempted to try adding the missing accelerometer too, but in the end it's easier and cheaper to make a board with the 2$ module.

[NeverDie]

Speaking of which, I shrunk the HolyIOT board a bit and added the small buzzer:

Hopefully this is small enough that it can be used as a locator beacon.

It turns out this is pretty nearly the minimum size, even if the HolyIOT were smaller, because of the CR2032 battery underneath it. Anyway, that's an interesting result, because the BC182 is smaller than the HolyIOT, but I wouldn't get the benefit of it.

[Nca78]

@neverdie said in nRF5 Bluetooth action!:

small buzzer:
CR2032 battery

If I'm not wrong this buzzer needs over 100mA, not sure it's a good match for a CR2032 ?

[MiKa]

@mika said in nRF5 Bluetooth action!:

Hi,
Working without problem with mysensors, I use STLink v2 from Aliexpress. LED and Button are mapped on pins 28 and 29 :)

Im just reporting sketch from NeverDie ;)

https://www.openhardware.io/view/510/Multi-Sensor-TempHumidityPIR-LeakMagnetLightAccel

[NeverDie]

@nca78 said in nRF5 Bluetooth action!:

@neverdie said in nRF5 Bluetooth action!:

small buzzer:
CR2032 battery

If I'm not wrong this buzzer needs over 100mA, not sure it's a good match for a CR2032 ?

I like how nothing slips past you! Yes, it's a pretty severe trade-off in exchange for its small size. So, I'll be using two CR2032's and make it run only in very short bursts. I honestly don't know how well or badly it will turn out.

[Nca78]

@neverdie said in nRF5 Bluetooth action!:

I like how nothing slips past you! Yes, it's a pretty severe trade-off in exchange for its small size. So, I'll be using two CR2032's and make it run only in very short bursts. I honestly don't know how well or badly it will turn out.

I don't see anything to co trim such a high current on your board ? Maybe it's the reason the sound level is low on your other board, max current of the MCU pin is much lower than what the buzzer needs ?

[NeverDie]

@nca78 said in nRF5 Bluetooth action!:

@neverdie said in nRF5 Bluetooth action!:

I like how nothing slips past you! Yes, it's a pretty severe trade-off in exchange for its small size. So, I'll be using two CR2032's and make it run only in very short bursts. I honestly don't know how well or badly it will turn out.

I don't see anything to co trim such a high current on your board ? Maybe it's the reason the sound level is low on your other board, max current of the MCU pin is much lower than what the buzzer needs ?

What does "co trim" mean?

[Nca78]

@neverdie said in nRF5 Bluetooth action!:

What does "co trim" mean?

Sorry phone rewriting what I type.
"Control".
MCU pins can't source that much current and I see no transistor on your board to do it ?
If you put a reserve capacitor big enough to supply 100+mA long enough to make some sound on the buzzer, will you not fry the pin ?

[NeverDie]

@nca78

The present design uses a TPS22860 load switch to turn on and off the buzzer. I'm not trying to power the buzzer directly from one of the nRF52832 pins, because the current would be outside the maximum limits for the nRF52832 pin. I'm hoping the two CR2032's will give enough headroom that the voltage (after the LDO) will be stable.

[Nca78]

@neverdie didn't now this chip, nice one thank you I've added it to my next order.
Seems I should have a better look at your designs :)

[NeverDie]

@nca78 said in nRF5 Bluetooth action!:

I received the "holyiot" modules and they are really, really tiny. 2 attached together are exactly the same size than the 51822-04 module. WL-CSP package is very impressive: small, very thin and with a cool shinny surface.
This module has inductors for DC/DC mode, and pins .00 and .01 are mapped so it's possible to add low frequency crystal for Bluetooth mode.

Have you tried uploading anything to the HolyIOT modules? I've now tried on two different HolyIOT modules, both without success. :(

[Nca78]

@neverdie said in nRF5 Bluetooth action!:

Have you tried uploading anything to the HolyIOT modules? I've now tried on two different HolyIOT modules, both without success. :(

Sorry not yet, I've just re-plugged my NRF5 board and I'm figuring out how to program external board. I'll do it with a board I know works, then try the holyiot module;