Waterpulse Sensor - ESP8266GW without Radio only as node

[HarrySteff]

Mhhh, nobody has an idea?
It seems that the sensor did not "start" the "void presentation()" section of sketch... :-(

[mfalkvidd]

@HarrySteff the code looks good to me. Could you post the full debug output?

[HarrySteff]

Okay i will, as soon as I'am back home... maybe monday! Thank you so far

[gohan]

What controller are you using? Because I'd comment out the define my controller address

[HarrySteff]

Iam using Pimatic, but only for displaying Sensor values. I set my node ID's manually...

[HarrySteff]

@mfalkvidd Here is my Serial Output:

MCO:BGN:INIT GW,CP=R-NGE---,VER=2.2.0-beta
scandone
f 0, scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 0 (29)
..reconnect
f -180, scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 0 (29)
..reconnect
f r0, scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 0 (29)
..reconnect
f 0, .scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 0 (29)
..reconnect
f -180, scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 0 (29)
..reconnect
f r0, scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 3
cnt 

connected with Fritzbox7390, channel 10
ip:192.168.0.137,mask:255.255.255.0,gw:192.168.0.1
.IP: 192.168.0.137
0;255;3;0;9;6400 MCO:BGN:STP
0;255;3;0;9;6473 MCO:REG:NOT NEEDED
0;255;3;0;9;6510 MCO:BGN:INIT OK,TSP=NA
pm open,type:2 0

And nothing more happens...
I tried to give out some serial prints in "void presentation" section, but they did not appear...

Strange...

For what is the MY_CONTROLLER_IP_ADRESS ? The IP i inserted here is the IP from my other/main "Mysensors-Gateway..."

[mfalkvidd]

@HarrySteff a controller and a gateway are different things. See https://www.mysensors.org/about/network#the-controller for information on what a controller is.

Try removing that define as per gohan's recommendation.

[HarrySteff]

Okay i understood this, but how does my ESP8266 node (only wifi) knows where the gateway is`?
I think i must tell it somwhere?
I will try to remove defined
MY_CONTROLLER_IP_ADRESS & MY_USE_UDP

posting serial output here...

[gohan]

it doesn't, if you use a esp8266 as a node without nrf24/rmf69 radio it needs to be a gateway on its own

[HarrySteff]

It is a gateway, here the serial output:
(nothing changes)

⸮Hl⸮G⸮C⸮d⸮xpI⸮⸮0;255;3;0;9;338 MCO:BGN:INIT GW,CP=R-NGE---,VER=2.2.0-beta
scandone
f 0, scandone
state: 0 -> 2 (b0)
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 1
cnt 

connected with Fritzbox7390, channel 1
ip:192.168.0.137,mask:255.255.255.0,gw:192.168.0.1
.IP: 192.168.0.137
0;255;3;0;9;899 MCO:BGN:STP
0;255;3;0;9;948 MCO:REG:NOT NEEDED
0;255;3;0;9;1004 MCO:BGN:INIT OK,TSP=NA
pm open,type:2 0

No local atached Sensor is presented?!?
I use a wemos d1 Mini...
Sensor is connected to Port D2
What digital-Input-Port Must i use?
I found some Pin mappings:
There it is Port 4

[gohan]

On the controller, did you add the 192.168.0.137 as a mysensors gateway?

[HarrySteff]

No, until now i did not, but do i need a controller at all?
(In my opinion it should present values even i do not have a controller)
So now i even disabled the define of the controller IP in my sketch...

[gohan]

The esp8266 is a complete stand alone mysensors network, it can't interact with the other unless you use a controller in between