Sketch for Lightning Sensor

[alexsh1]

I found a similar sensor in the UK and added this to the list of my to be sensors for the weatherstation. Can I use it inside or it has to be placed outside to have a direct vision?

http://www.embeddedadventures.com/as3935_lightning_sensor_module_mod-1016.html

[Tore André Rosander]

@alexsh1 What i read when researching this chip it can be placed inside.

@Sparkman Nice, i see that it has a detection range about 40km so thats already a pretty good distance to get a notification when lightning is detected.

[alexsh1]

@Sparkman I suppose your wiring diagram above is correct? I noted that the sensor is not working with 3.3V. Did you manage to find what the problem was? Looking at the datasheet http://www.embeddedadventures.com/datasheets/MOD-1016_hw_v8_doc_v4.pdf I can see what the module can operate down to 2.4V

I am going to receive the sensor in a few days and test it.

As I have a different module manufacturer, I may need to change the sketch as it uses a different library. This is unmodified example sketch:

*/

// AS3935 MOD-1016 Lightning Sensor Arduino test sketch
// Written originally by Embedded Adventures


#include <Wire.h>
#include <AS3935.h>

#define IRQ_pin 2

volatile bool detected = false;

void setup() {
  Serial.begin(115200);
  while (!Serial) {}
  Serial.println("Welcome to the MOD-1016 (AS3935) Lightning Sensor test sketch!");
  Serial.println("Embedded Adventures (www.embeddedadventures.com)\n");

  Wire.begin();
  mod1016.init(IRQ_pin);
 
  //Tune Caps, Set AFE, Set Noise Floor
  //autoTuneCaps(IRQ_pin);
  
  mod1016.setTuneCaps(7);
  mod1016.setOutdoors();
  mod1016.setNoiseFloor(5);
  
  
  Serial.println("TUNE\tIN/OUT\tNOISEFLOOR");
  Serial.print(mod1016.getTuneCaps(), HEX);
  Serial.print("\t");
  Serial.print(mod1016.getAFE(), BIN);
  Serial.print("\t");
  Serial.println(mod1016.getNoiseFloor(), HEX);
  Serial.print("\n");

  pinMode(IRQ_pin, INPUT);
  attachInterrupt(digitalPinToInterrupt(IRQ_pin), alert, RISING);
  Serial.println("after interrupt");
}

void loop() {
  if (detected) {
    translateIRQ(mod1016.getIRQ());
    detected = false;
  }
}

void alert() {
  detected = true;
}

void translateIRQ(uns8 irq) {
  switch(irq) {
      case 1:
        Serial.println("NOISE DETECTED");
        break;
      case 4:
        Serial.println("DISTURBER DETECTED");
        break;
      case 8: 
        Serial.println("LIGHTNING DETECTED");
        printDistance();
        break;
    }
}

void printDistance() {
  int distance = mod1016.calculateDistance();
  if (distance == -1)
    Serial.println("Lightning out of range");
  else if (distance == 1)
    Serial.println("Distance not in table");
  else if (distance == 0)
    Serial.println("Lightning overhead");
  else {
    Serial.print("Lightning ~");
    Serial.print(distance);
    Serial.println("km away\n");  
  }
}

This is SPI sketch, I'd like to use I2C connection. Generally, the procedure is as follows:

Wait a few milliseconds for the system to stabilise
 Set the tune capacitor to the value indicated on the packaging, by setting the
TUNE_CAP bits of register 8
 Wait 2 milliseconds
 Callibrate RCO by:
o Sending a calibrate RCO direct command (set memory location 0x3d to the
value 0x96)
o Set Register 0x08, bit 5 to 1
o Wait 2 milliseconds
o Set Register 0x08, bit 5 to 0
The factory calibrating tuning cap value will be fine for general use. When you have a
MOD-1016 in an enclosure or close to other electronics it is worth calibrating the tuning
cap again.

[scalz]

can't wait to test this one too ;) i have pcbs for a weather shield (with bme280, veml6070 etc. ) and i have this sensor on it too (https://forum.mysensors.org/uploads/files/1459631385870-stacked.jpg). But not assembled yet, was busy, i hope asap.. i plan to use it with 3v and i2c. @alexsh1 There are libs for i2c if you want :)

Thx @Sparkman for your work on it ;)

[alexsh1]

@scalz yes, please (for i2c lib). What is this red board you have?

[Sparkman]

@alexsh1 @scalz

I'm running my sketch with I2C now, rather than SPI. I found the sensor would lock up occassionally, so recently converted it and am still testing it. I have mine running at 5v now as well instead of 3.3v, but it works fine with either.

I'll post an updated sketch (and wiring diagram) soon. I based both the spi and i2c sketches on the examples found here: http://playingwithfusion.com/productview.php?pdid=22&catid=1001.

Cheers
Al

[alexsh1]

@Sparkman Thanks. Your sketch is very much appreciated. I'll have to adopt it anyway as I have a different manufacture and there is a certain process I have to follow to get it initiated (posted above).

[alexsh1]

Absolutely delighted with the module I have received today by post. The weather is sh@t tonight (lightning, rain etc.) which means that I can test it:

Welcome to the MOD-1016 (AS3935) Lightning Sensor test sketch!
TUNE	IN/OUT	NOISEFLOOR
6	10010	5

after interrupt
DISTURBER DETECTED
DISTURBER DETECTED
DISTURBER DETECTED
DISTURBER DETECTED
DISTURBER DETECTED
LIGHTNING DETECTED
Lightning ~27km away

DISTURBER DETECTED
DISTURBER DETECTED
LIGHTNING DETECTED
Lightning ~17km away

DISTURBER DETECTED
LIGHTNING DETECTED
Lightning ~10km away

I calibrated the sensor and put a reasonable "noise floor". Now I have to convert it into MySensors and hook up to the ceech board outside.

@Sparkman I have my sensor running at 3.3V

[alexsh1]

BTW, I am not sure the sensor is similar to what you guys have.

[Sparkman]

@alexsh1 It looks to be a different breakout board, but for the same chip. So I would expect them to work basically the same.

Cheers
Al

[alexsh1]

@Sparkman it is a different board made (or designed) by a UK company.

We are having a real British summer over here :-)))

LIGHTNING DETECTED
Lightning ~20km away

LIGHTNING DETECTED
Lightning ~20km away

LIGHTNING DETECTED
Lightning ~6km away

LIGHTNING DETECTED
Lightning ~6km away

LIGHTNING DETECTED
Lightning ~6km away

LIGHTNING DETECTED
Lightning ~6km away

LIGHTNING DETECTED
Lightning ~6km away

LIGHTNING DETECTED
Lightning ~5km away

[NeverDie]

@alexsh1
There doesn't appear to be audio input to this board, nor a microphone on the board. So, how does it estimate the distance to the lightening?

[Sparkman]

@NeverDie All these breakout boards are based on this chip: http://ams.com/eng/Products/Wireless-Connectivity/Wireless-Sensor-Connectivity/AS3935. They use a proprietary method to figure out distance and is not based on sound.

Cheers
Al

[NeverDie]

@Sparkman said:

@NeverDie All these breakout boards are based on this chip: http://ams.com/eng/Products/Wireless-Connectivity/Wireless-Sensor-Connectivity/AS3935. They use a proprietary method to figure out distance and is not based on sound.

Cheers
Al

Any impression yet as to how accurate its distance estimates are?

[Sparkman]

@NeverDie No, as we've had very little lightning since I started using it.

[alexsh1]

@NeverDie Al, was quicker replying to your question. :-)
yes, I think it is accurate for my needs - if a lightning detected at, say, 10km+/- 1km this is ok. How accurate do you want it to be?

This is a great technology

[NeverDie]

@alexsh1 said:

@NeverDie Al, was quicker replying to your question. :-)
How accurate do you want it to be?

I'm not sure, but more accurate than lightningmaps.com or it's a no-go. I've played with lightningmaps.com during a few thunderstorms, and although it's great for getting a general idea of lightning strike rate and density, I was surprised that it seems to miss a lot of detections entirely that both my eyes and ears have confirmed. e.g. some strikes that were big enough to rattle the windows didn't show up at all on lightningmaps. Some of the others were detected, but the map plot of the strike was wrong by maybe 10 miles or so.

[alexsh1]

@NeverDie I have not tested this sensor long enough, but recently we have had torrential rain, lightning, etc - you can see some data I published above. The sensor did not miss a single one. There are a few parameters you can alter (noise floor). One has to setup it correctly. I have not started looking into converting the sketch for MySensors yet

[alexsh1]

I have adopted the MOD-1016 module (https://www.embeddedadventures.com/datasheets/MOD-1016_hw_v8_doc_v4.pdf) for MySensors if anyone is interested:

/*

Copyright (c) 2016, Embedded Adventures
All rights reserved.

Contact us at source [at] embeddedadventures.com
www.embeddedadventures.com

Redistribution and use in source and binary forms, with or without
modification, are permitted provided that the following conditions are met:

- Redistributions of source code must retain the above copyright notice,
  this list of conditions and the following disclaimer.

- Redistributions in binary form must reproduce the above copyright
  notice, this list of conditions and the following disclaimer in the
  documentation and/or other materials provided with the distribution.

- Neither the name of Embedded Adventures nor the names of its contributors
  may be used to endorse or promote products derived from this software
  without specific prior written permission.
 
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN 
CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF 
THE POSSIBILITY OF SUCH DAMAGE.

*/

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69
#define MY_NODE_ID 15

#include <Wire.h>
#include <MySensors.h>
#include <AS3935.h> // AS3935 MOD-1016 by Embedded Adventures

volatile bool detected = false;


 //-----------------IMPORTANT--------------------
 //---------------CHANGE SETTINGS HERE-----------
#define IRQ_pin 2

#define AS3935_TUNE_CAPS     6 // <-- SET THIS VALUE TO THE NUMBER LISTED ON YOUR BOARD 
#define AS3935_INDOORS       1 // AS3935_INDOORS=1 indoors, AS3935_INDOORS=0 outdoors
#define AS3935_NOISE_FLOOR   6
#define AS3935_ENABLE_DISTURBERS 1 // 0 or 1      

#define CHILD_ID_DISTANCE 1
#define CHILD_ID_INTENSITY 2
MyMessage msgDist(CHILD_ID_DISTANCE, V_DISTANCE);
MyMessage msgInt(CHILD_ID_INTENSITY, V_VAR1);

void setup()  
{ 
  Serial.begin(115200);
  while (!Serial) {}
  Serial.println("MOD-1016 (AS3935) Lightning Sensor");
  Serial.println("beginning boot procedure....");
  
  Wire.begin();
  mod1016.init(IRQ_pin);
 
 //-----------------IMPORTANT--------------------
 //---------------CHANGE SETTINGS HERE-----------
  //Tune Caps, Set AFE, Set Noise Floor
  //autoTuneCaps(IRQ_pin);
  mod1016.setTuneCaps(AS3935_TUNE_CAPS);
delay(2);
#if AS3935_INDOORS == 1
  mod1016.setIndoors();
  #else
  mod1016.setOutdoors();
#endif
delay(2);
mod1016.setNoiseFloor(AS3935_NOISE_FLOOR);
delay(2);
#if AS3935_ENABLE_DISTURBERS == 1
  mod1016.enableDisturbers();
#else
  mod1016.disableDisturbers();
#endif
//mod1016.calibrateRCO();
delay(2);
  Serial.println("TUNE\tIN/OUT\tNOISEFLOOR");
  Serial.print(mod1016.getTuneCaps(), HEX);
  Serial.print("\t");
  Serial.print(mod1016.getAFE(), BIN);
  Serial.print("\t");
  Serial.println(mod1016.getNoiseFloor(), HEX);
  Serial.print("\n");

  pinMode(IRQ_pin, INPUT);
  attachInterrupt(digitalPinToInterrupt(IRQ_pin), alert, RISING);
  Serial.println("after interrupt");
    // delay execution to allow chip to stabilize.
  delay(1000);

}

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Lightning Sensor MOD-1016", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID_DISTANCE, S_DISTANCE);
  present(CHILD_ID_INTENSITY, S_CUSTOM);
}

void loop() {
  if (detected) {
    translateIRQ(mod1016.getIRQ());
    detected = false;
  }
}

void alert() {
  detected = true;
}

void translateIRQ(uns8 irq) {
  switch(irq) {
      case 1:
        Serial.println("Noise detected");
        break;
      case 4:
        Serial.println("Disturber detected");
        break;
      case 8: 
        Serial.println("Lightning detected!");
        printandsendToGW();
        break;

  }
}

void printandsendToGW() {
  int distance = mod1016.calculateDistance();
  unsigned int lightning_intensity = mod1016.getIntensity();
  if (distance == -1)
    Serial.println("Lightning out of range");
  else if (distance == 1)
    Serial.println("Distance not in table");
  else if (distance == 0)
    Serial.println("Lightning overhead");
  else {
    Serial.print("Lightning ~");
    Serial.print(distance);
    Serial.println("km away\n");
    Serial.print("Lightning Intensity: ");
    Serial.println(lightning_intensity);  
    send(msgDist.set(distance));
    send(msgInt.set(lightning_intensity));
  }
}

You have to change the sketch according to your module settings

[skywatch]

I ordered one form embedded adventures on 27/7 - Now it is 3/9 and still nothing.
Waiting to hear from them....
That's the whole truth.