UI7

[olaeke]

@axillent Sure what do I need to place it in the source control? I have an account on GitHub

[hek]

I've created a UI7-branch.

https://github.com/mysensors/Vera/tree/UI7

Maybe you could create a pull request on that when you're finished?

http://forum.mysensors.org/topic/330/how-to-contribute-code-to-the-mysensors-project

[olaeke]

@hek Done, I have not used GitHub before (more used to MS Tools) and there was some steps to take to check in but I hope I managed to do it.

[gregl]

Have you guys seen this : http://forum.micasaverde.com/index.php/topic,30310.0/topicseen.html

i havent tested it yet, but great there seems a way to make the UI7 more usable!

[hek]

Ok, a couple of UI7 PRs has been merged here:

https://github.com/mysensors/Vera/tree/UI7

Testers needed.

[filipq]

Just uploaded files to my Vera Lite. Screenshot's below. I'm using Internet Explorer 11. Firefox looks identical.

It looks much better.

[Dany]

I have a VeraEdge, but I have with lot of problem.
I'm using an Ethernet gateway, and downloaded the latest Vera plugins and libraries mysensors from Github.

But Vera says everytime communication error...

[blacey]

Here are the requested screenshots from UI5...

[olaeke]

@Dany Can you ping your gateway? Sometimes I have problem that my Ethernet just "die", but after reset on card and Arduino it works again.

[Dany]

@olaeke Yes, I can ping the gateway. This board works fine as MQTT gateway with the openhab.
But the library version is 1.4, not 1.4.1. How can I download the libraries 1.4.1?

[abalazs]

@olaeke & @Dany Clumsy is not the problem that the original bootloader to use it? The Ethernet gateway both of us produces the same error. OpenHAB all worked well as MQTT.

[olaeke]

@Dany You will get 1.41 on the download link http://www.mysensors.org/download/. I have no problem access my Gateway with Ethernet, I'm using W5100 module and the lib from the download link.

[pstoian]

Hi, I am getting the same error as @Dany .... I am using an W5100 / Ethernet gateway. I downloaded the latest library but still the library is not listed into the device.

Also I can ping successfully the gateway. Any advice is much appreciated. Thank you.

[mjunqueira]

I managed to use Serial Gateway in my Ver Edge´s UI7 pulling a support ticket in the link http://getvera.com/support/. They asked me to enable the remote support to access my controller and than they updated my open WRT firmware to the latest one and now i can use the Serial Ports normally.

[mikemayers]

@mjunqueira
good to know you got Serial to worked.

[BulldogLowell]

Anyone else getting this persistent error using UI7 and ethernet gateway?

trying to upgrade....

It works (messages go both ways) but this error won't go away...

[korttoma]

Jim I read this from the Vera forum maybe it is only for z-wave devices or maybe might help for you also:

If you have a device that functions fine, and yet reports "Can't detect device", the following may work for you;

1) Change the variable CommFailure from "-1" to "0" (click outside the box to save)
2) Clear the variable LastCommFailure (going from memory here; it is right next to the CommFailure) field (click outside the box)
3) Go to the device settings, and change the "Automatically configure" to "no"

Once the "error" has cleared, step 3 (I think) keeps it cleared.

I don't have any personal experience since I'm not ready to move from UI5 just yet..

[BulldogLowell]

@korttoma

Hey Tomas, thanks!

That seems to have worked.

I'll update if there is a problem.

Other than this issue, I think UI7 is OK for me (testing in one location only :) )