Skip to content
  • MySensors
  • OpenHardware.io
  • Categories
  • Recent
  • Tags
  • Popular
Skins
  • Light
  • Brite
  • Cerulean
  • Cosmo
  • Flatly
  • Journal
  • Litera
  • Lumen
  • Lux
  • Materia
  • Minty
  • Morph
  • Pulse
  • Sandstone
  • Simplex
  • Sketchy
  • Spacelab
  • United
  • Yeti
  • Zephyr
  • Dark
  • Cyborg
  • Darkly
  • Quartz
  • Slate
  • Solar
  • Superhero
  • Vapor
  • Default (No Skin)
  • No Skin
Collapse
Brand Logo
  1. Home
  2. Troubleshooting
  3. Cannot run MySensors on RPI 3

Cannot run MySensors on RPI 3

Scheduled Pinned Locked Moved Troubleshooting
32 Posts 9 Posters 3.5k Views 9 Watching
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • kkanedaaK kkanedaa

    Hello all,

    I have been reading and trying for 3 days now without success and simply do not know what to do anymore. I do not know what the problem is. Maybe I am misunderstanding the whole concept of MySensors? Anyways, let me explain.

    My main issue seems to be not able to run the gateway.

    The way I understand it, is that I can use the RPI 3 as both gateway and run a controller on it at the same time (in this case MyController).

    I followed the instructions on the MySensor's RPI page. Here is what I did:

    • Connected the NRF24L01+ to RPI3's pins (I triple-checked that all wires are correct)
    • I then entered the following commands:
    git clone https://github.com/mysensors/MySensors.git --branch master
cd MySensors
./configure --my-transport=nrf24
./configure --my-gateway=mqtt --my-controller-ip-address=[IP-OF-MY-RPI] --my-mqtt-publish-topic-prefix=mysensors-out --my-mqtt-subscribe-topic-prefix=mysensors-in --my-mqtt-client-id=mygateway1
make
sudo ./bin/mysgw -d

    But I get the following error message:

    pi@rpi-lite:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT
mysgw: TSM:FAIL:RE-INIT
mysgw: TSM:INIT
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=2
mysgw: TSM:FAIL:PDT
^Cmysgw: Received SIGINT

    So already here I am stuck...

    Then I tried to use a WeMos D1 Mini connected to an NRF24 to create a gateway. I used all default settings to upload the sketch (which I got from Examples > MySensor > GatewayESP8266MQTTClient.

    I made sure to add the correct IP for my WeMos in the sketch under
    #define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68

    But when adding it to MyController.org's gateways the status is "unavailable"...

    What am I doing wrong?

    Ideally, I would wish the NRF24 to be hooked up to my RPI.

    Does anyone know what I am doing wrong?

    Thanks in advance :)

    mfalkviddM Offline
    mfalkviddM Offline
    mfalkvidd
    Mod
    wrote on last edited by mfalkvidd
    #2

    @kkanedaa welcome to the MySensors community! Sorry for your troubles.

    All parameters to the ./configure command need to be entered on one line, like this:

    ./configure --my-transport=nrf24 --my-gateway=mqtt --my-controller-ip-address=[IP-OF-MY-RPI] --my-mqtt-publish-topic-prefix=mysensors-out --my-mqtt-subscribe-topic-prefix=mysensors-in --my-mqtt-client-id=mygateway1

    In your case it doesn't matter, because nrf24 is the default choice anyway. But it might be good to know if you change to another configuration later :)

    This part of the log:

    mysgw: !TSM:INIT:TSP FAIL

    indicates that the gateway software is unable to talk to the radio module. Since you've already triple-checked the wiring, maybe you could upload pictures of the wiring, to get a fresh pair of eyes on it?

    If you have another nrf24 radio module, it could be good to replace the one you are using, to rule out that there is something wrong with the nrf24 module. Or try the radio module on another device (your wemos d1 mini for example) to verify that it works there.

    Did the make command produce any warnings? If it did, those could be needing attention.

    1 Reply Last reply
    0
    • kkanedaaK Offline
      kkanedaaK Offline
      kkanedaa
      wrote on last edited by kkanedaa
      #3

      @mfalkvidd said in Cannot run MySensors on RPI 3:

      ./configure --my-transport=nrf24 --my-gateway=mqtt --my-controller-ip-address=[IP-OF-MY-RPI] --my-mqtt-publish-topic-prefix=mysensors-out --my-mqtt-subscribe-topic-prefix=mysensors-in --my-mqtt-client-id=mygateway1

      Hi thanks for the quick reply.

      I checked the NRF24 module by communicating with each other and it works fine...so I don't think the problem is with the module.

      I attached 2 photos of my wiring of the NRF with my Pi so you can have a look.

      As for error messages while "make" - none.

      Here is the output of make:

      pi@rpi-lite:~/MySensors $ make
gcc -MT build/drivers/Linux/log.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/log.c -o build/drivers/Linux/log.o
g++ -MT build/drivers/Linux/IPAddress.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/IPAddress.cpp -o build/drivers/Linux/IPAddress.o
g++ -MT build/drivers/Linux/noniso.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/noniso.cpp -o build/drivers/Linux/noniso.o
g++ -MT build/drivers/Linux/GPIO.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/GPIO.cpp -o build/drivers/Linux/GPIO.o
g++ -MT build/drivers/Linux/Print.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/Print.cpp -o build/drivers/Linux/Print.o
g++ -MT build/drivers/Linux/EthernetClient.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/EthernetClient.cpp -o build/drivers/Linux/EthernetClient.o
g++ -MT build/drivers/Linux/compatibility.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/compatibility.cpp -o build/drivers/Linux/compatibility.o
g++ -MT build/drivers/Linux/SerialPort.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/SerialPort.cpp -o build/drivers/Linux/SerialPort.o
g++ -MT build/drivers/Linux/Stream.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/Stream.cpp -o build/drivers/Linux/Stream.o
g++ -MT build/drivers/Linux/interrupt.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/interrupt.cpp -o build/drivers/Linux/interrupt.o
g++ -MT build/drivers/Linux/SerialSimulator.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/SerialSimulator.cpp -o build/drivers/Linux/SerialSimulator.o
g++ -MT build/drivers/Linux/SoftEeprom.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/SoftEeprom.cpp -o build/drivers/Linux/SoftEeprom.o
g++ -MT build/drivers/Linux/EthernetServer.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/EthernetServer.cpp -o build/drivers/Linux/EthernetServer.o
g++ -MT build/examples_linux/mysgw.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c examples_linux/mysgw.cpp -o build/examples_linux/mysgw.o
g++ -MT build/drivers/SPIDEV/SPI.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/SPIDEV/SPI.cpp -o build/drivers/SPIDEV/SPI.o
g++ -pthread  -o bin/mysgw build/drivers/Linux/log.o build/drivers/Linux/IPAddress.o build/drivers/Linux/noniso.o build/drivers/Linux/GPIO.o build/drivers/Linux/Print.o build/drivers/Linux/EthernetClient.o build/drivers/Linux/compatibility.o build/drivers/Linux/SerialPort.o build/drivers/Linux/Stream.o build/drivers/Linux/interrupt.o build/drivers/Linux/SerialSimulator.o build/drivers/Linux/SoftEeprom.o build/drivers/Linux/EthernetServer.o build/examples_linux/mysgw.o  build/drivers/SPIDEV/SPI.o

      And then again the error when running sudo ./bin/mysgw -d:

      pi@rpi-lite:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT

      And here the photos:

      • CE = yellow
      • CSN = green
      • SCK = blue
      • MO = violet
      • MI = grey
      • IRQ = white

      alt text
      alt text

      Would you know what I am doing wrong? :(

      I really want to get this to work.

      Thanks again in advance.

      mfalkviddM 1 Reply Last reply
      1
      • kkanedaaK kkanedaa

        @mfalkvidd said in Cannot run MySensors on RPI 3:

        ./configure --my-transport=nrf24 --my-gateway=mqtt --my-controller-ip-address=[IP-OF-MY-RPI] --my-mqtt-publish-topic-prefix=mysensors-out --my-mqtt-subscribe-topic-prefix=mysensors-in --my-mqtt-client-id=mygateway1

        Hi thanks for the quick reply.

        I checked the NRF24 module by communicating with each other and it works fine...so I don't think the problem is with the module.

        I attached 2 photos of my wiring of the NRF with my Pi so you can have a look.

        As for error messages while "make" - none.

        Here is the output of make:

        pi@rpi-lite:~/MySensors $ make
gcc -MT build/drivers/Linux/log.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/log.c -o build/drivers/Linux/log.o
g++ -MT build/drivers/Linux/IPAddress.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/IPAddress.cpp -o build/drivers/Linux/IPAddress.o
g++ -MT build/drivers/Linux/noniso.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/noniso.cpp -o build/drivers/Linux/noniso.o
g++ -MT build/drivers/Linux/GPIO.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/GPIO.cpp -o build/drivers/Linux/GPIO.o
g++ -MT build/drivers/Linux/Print.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/Print.cpp -o build/drivers/Linux/Print.o
g++ -MT build/drivers/Linux/EthernetClient.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/EthernetClient.cpp -o build/drivers/Linux/EthernetClient.o
g++ -MT build/drivers/Linux/compatibility.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/compatibility.cpp -o build/drivers/Linux/compatibility.o
g++ -MT build/drivers/Linux/SerialPort.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/SerialPort.cpp -o build/drivers/Linux/SerialPort.o
g++ -MT build/drivers/Linux/Stream.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/Stream.cpp -o build/drivers/Linux/Stream.o
g++ -MT build/drivers/Linux/interrupt.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/interrupt.cpp -o build/drivers/Linux/interrupt.o
g++ -MT build/drivers/Linux/SerialSimulator.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/SerialSimulator.cpp -o build/drivers/Linux/SerialSimulator.o
g++ -MT build/drivers/Linux/SoftEeprom.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/SoftEeprom.cpp -o build/drivers/Linux/SoftEeprom.o
g++ -MT build/drivers/Linux/EthernetServer.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/EthernetServer.cpp -o build/drivers/Linux/EthernetServer.o
g++ -MT build/examples_linux/mysgw.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c examples_linux/mysgw.cpp -o build/examples_linux/mysgw.o
g++ -MT build/drivers/SPIDEV/SPI.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID=\"mygateway1\" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX=\"mysensors-in\" -DMY_MQTT_PUBLISH_TOPIC_PREFIX=\"mysensors-out\" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166  -Ofast -g -Wall -Wextra  -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/SPIDEV/SPI.cpp -o build/drivers/SPIDEV/SPI.o
g++ -pthread  -o bin/mysgw build/drivers/Linux/log.o build/drivers/Linux/IPAddress.o build/drivers/Linux/noniso.o build/drivers/Linux/GPIO.o build/drivers/Linux/Print.o build/drivers/Linux/EthernetClient.o build/drivers/Linux/compatibility.o build/drivers/Linux/SerialPort.o build/drivers/Linux/Stream.o build/drivers/Linux/interrupt.o build/drivers/Linux/SerialSimulator.o build/drivers/Linux/SoftEeprom.o build/drivers/Linux/EthernetServer.o build/examples_linux/mysgw.o  build/drivers/SPIDEV/SPI.o

        And then again the error when running sudo ./bin/mysgw -d:

        pi@rpi-lite:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG---,VER=2.1.1
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: !TSM:INIT:TSP FAIL
mysgw: TSM:FAIL:CNT=1
mysgw: TSM:FAIL:PDT

        And here the photos:

        • CE = yellow
        • CSN = green
        • SCK = blue
        • MO = violet
        • MI = grey
        • IRQ = white

        alt text
        alt text

        Would you know what I am doing wrong? :(

        I really want to get this to work.

        Thanks again in advance.

        mfalkviddM Offline
        mfalkviddM Offline
        mfalkvidd
        Mod
        wrote on last edited by mfalkvidd
        #4

        @kkanedaa it looks like the "adapter board" you're using for the nrf24 has got an LDO on it. Is that the case? If so, is 3.3V sufficient for it? If you used it when you checked that the nrf24 works then it should be fine. But just to try to eliminate possible problem sources, how about connecting the nrf24 directly to the raspberry pi?

        It is recommended to place the capacitor as close to vcc/gnd on the nrf24 as possible. I see on the picture that it is placed at the input to the adapter board.

        kkanedaaK 1 Reply Last reply
        0
        • mfalkviddM Offline
          mfalkviddM Offline
          mfalkvidd
          Mod
          wrote on last edited by
          #5

          The connections on the raspberry pi side look good. I can't see if the connections to the adapter board are correct because I'm not familiar with that board. Would you mind posting a photo where the adapter board silkscreen / labels are visible?

          1 Reply Last reply
          0
          • sburlotS Offline
            sburlotS Offline
            sburlot
            wrote on last edited by
            #6

            @kkanedaa said in Cannot run MySensors on RPI 3:

            gcc -MT build/drivers/Linux/log.o -MMD -MP -DMY_RADIO_NRF24 -DMY_GATEWAY_LINUX -DMY_GATEWAY_MQTT_CLIENT -DMY_DEBUG -DLINUX_SPI_SPIDEV -DMY_MQTT_CLIENT_ID="mygateway1" -DMY_MQTT_SUBSCRIBE_TOPIC_PREFIX="mysensors-in" -DMY_MQTT_PUBLISH_TOPIC_PREFIX="mysensors-out" -DMY_CONTROLLER_IP_ADDRESS=192,168,xx,166 -Ofast -g -Wall -Wextra -I. -I./core -I./drivers/Linux -I./drivers/SPIDEV -c drivers/Linux/log.c -o build/drivers/Linux/log.o

            I dont know if it's important, but your configure didn't detect the BCM chip for SPI?
            Did you enable SPI via raspi-config (or /boot/config.txt) ?

            1 Reply Last reply
            1
            • mfalkviddM mfalkvidd

              @kkanedaa it looks like the "adapter board" you're using for the nrf24 has got an LDO on it. Is that the case? If so, is 3.3V sufficient for it? If you used it when you checked that the nrf24 works then it should be fine. But just to try to eliminate possible problem sources, how about connecting the nrf24 directly to the raspberry pi?

              It is recommended to place the capacitor as close to vcc/gnd on the nrf24 as possible. I see on the picture that it is placed at the input to the adapter board.

              kkanedaaK Offline
              kkanedaaK Offline
              kkanedaa
              wrote on last edited by
              #7

              @mfalkvidd said in Cannot run MySensors on RPI 3:

              @kkanedaa it looks like the "adapter board" you're using for the nrf24 has got an LDO on it. Is that the case? If so, is 3.3V sufficient for it? If you used it when you checked that the nrf24 works then it should be fine. But just to try to eliminate possible problem sources, how about connecting the nrf24 directly to the raspberry pi?

              It is recommended to place the capacitor as close to vcc/gnd on the nrf24 as possible. I see on the picture that it is placed at the input to the adapter board.

              Hi there, thanks again for the reply :)

              I have removed the baseboard and attached the wires directly to the NRF24. I also moved the capacitor to Pi's VCC and GND.

              alt text

              As for the baseboard, if you are wondering, the layout looks like this. I always used it in all my NRF projects and never seemed to have a problem.

              alt text

              @sburlot said in Cannot run MySensors on RPI 3:

              I dont know if it's important, but your configure didn't detect the BCM chip for SPI?
              Did you enable SPI via raspi-config (or /boot/config.txt) ?

              Yep, SPI is enabled. Otherwise I would get error message while executing "make" (I guess). But thanks for trying to help :)

              I will try to get MySensors running now once again and let you guys know the results. Hope it will work this time...

              1 Reply Last reply
              0
              • kkanedaaK Offline
                kkanedaaK Offline
                kkanedaa
                wrote on last edited by
                #8

                Nope....still same error message....

                What am I doing wrong? :(

                1 Reply Last reply
                0
                • kkanedaaK Offline
                  kkanedaaK Offline
                  kkanedaa
                  wrote on last edited by kkanedaa
                  #9

                  @mfalkvidd Should I try to use the dev version? Also, should I "format" my SD card with a fresh install of Raspbian Stretch Lite?

                  Do you think this might help?

                  Also, it does not matter if my Pi runs the controller and MySensors at the same time, right?

                  1 Reply Last reply
                  0
                  • M Offline
                    M Offline
                    mickecarlsson
                    wrote on last edited by
                    #10

                    Download the development version of MySensors and try that. I could not get MySensors to work on a RPI 3 with the 2.1.1 version.

                    kkanedaaK 1 Reply Last reply
                    0
                    • gohanG Offline
                      gohanG Offline
                      gohan
                      Mod
                      wrote on last edited by
                      #11

                      There is a note in the raspberry page to use development version. BTW, did you connect the 5v pin to the nrf24 module? It seems so from the picture and if it's the case, say bye-bye to it. Also the capacitor it is better to be closer to the radio module and not on the raspberry gpio

                      1 Reply Last reply
                      0
                      • mikeeM Offline
                        mikeeM Offline
                        mikee
                        wrote on last edited by
                        #12

                        I had same problem (but on serial GW). It started after I removed IRQ connector. I was able to add devices (using Domoticz as controller) , bust after few hours it stops to work.

                        1 Reply Last reply
                        0
                        • gohanG Offline
                          gohanG Offline
                          gohan
                          Mod
                          wrote on last edited by
                          #13

                          I'm using irq pin without issues

                          1 Reply Last reply
                          0
                          • M mickecarlsson

                            Download the development version of MySensors and try that. I could not get MySensors to work on a RPI 3 with the 2.1.1 version.

                            kkanedaaK Offline
                            kkanedaaK Offline
                            kkanedaa
                            wrote on last edited by kkanedaa
                            #14

                            @mickecarlsson said in Cannot run MySensors on RPI 3:

                            Download the development version of MySensors and try that. I could not get MySensors to work on a RPI 3 with the 2.1.1 version.

                            I will try with the dev version and let you guys know again.

                            @gohan said in Cannot run MySensors on RPI 3:

                            There is a note in the raspberry page to use development version. BTW, did you connect the 5v pin to the nrf24 module? It seems so from the picture and if it's the case, say bye-bye to it. Also the capacitor it is better to be closer to the radio module and not on the raspberry gpio

                            Nope, it's connected to 3.3V. Regarding the capacitor, I had it first near the NRF24, but mfalkvidd told me to move it.

                            But thank you for your inputs, guys. I'll try the dev version and hope it will work.

                            mfalkviddM 1 Reply Last reply
                            0
                            • kkanedaaK kkanedaa

                              @mickecarlsson said in Cannot run MySensors on RPI 3:

                              Download the development version of MySensors and try that. I could not get MySensors to work on a RPI 3 with the 2.1.1 version.

                              I will try with the dev version and let you guys know again.

                              @gohan said in Cannot run MySensors on RPI 3:

                              There is a note in the raspberry page to use development version. BTW, did you connect the 5v pin to the nrf24 module? It seems so from the picture and if it's the case, say bye-bye to it. Also the capacitor it is better to be closer to the radio module and not on the raspberry gpio

                              Nope, it's connected to 3.3V. Regarding the capacitor, I had it first near the NRF24, but mfalkvidd told me to move it.

                              But thank you for your inputs, guys. I'll try the dev version and hope it will work.

                              mfalkviddM Offline
                              mfalkviddM Offline
                              mfalkvidd
                              Mod
                              wrote on last edited by
                              #15

                              @kkanedaa sorry for being unclear. I meant closer to the nrf24, not further away from it.

                              1 Reply Last reply
                              0
                              • kkanedaaK Offline
                                kkanedaaK Offline
                                kkanedaa
                                wrote on last edited by
                                #16
                                This post is deleted!
                                1 Reply Last reply
                                0
                                • kkanedaaK Offline
                                  kkanedaaK Offline
                                  kkanedaa
                                  wrote on last edited by
                                  #17

                                  Hey all,

                                  So I removed the stable version of MySensors and got the development version.

                                  Let me show you step by step what I did:

                                  sudo rm -r MySensors
git clone https://github.com/mysensors/MySensors.git --branch development
cd MySensors

./configure --my-transport=nrf24 --my-gateway=mqtt --my-controller-ip-address=[MY-PI-IP] --my-mqtt-publish-topic-prefix=mysensors-out --my-mqtt-subscribe-topic-prefix=mysensors-in --my-mqtt-client-id=mygateway1

make
sudo ./bin/mysgw -d

                                  [MY-PI-IP] has been changed to my RPI's IP.

                                  The output I got first is this:

                                  pi@rpi-lite:~/MySensors $ sudo ./bin/mysgw -d
mysgw: Starting gateway...
mysgw: Protocol version - 2.2.0-rc.2
mysgw: MCO:BGN:INIT GW,CP=RNNGL---,VER=2.2.0-rc.2
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7

                                  then it started going non-stop repeating the following output:

                                  mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: TSF:MSG:READ,0-0-0,s=0,c=0,t=0,pt=0,l=0,sg=0:
mysgw: !TSF:MSG:LEN,0!=7
mysgw: GWT:RMQ:MQTT RECONNECT
mysgw: connect: Connection refused
mysgw: failed to connect

                                  Now I have a problem with the gateway. Did I configure something wrong? Or did I forget a step?

                                  All help is very much appreciated :)

                                  1 Reply Last reply
                                  0
                                  • G Offline
                                    G Offline
                                    GRDL
                                    wrote on last edited by
                                    #18

                                    I struggled with RPi gateway for ages without success. The easiest solution by far is to run the gateway on arduino and interface it to RPI through a serial gateway. Its not a very elegant solution but works. I did some investigation and came to the conclusion that the problem with RPi gateway is to do with the low level library that communicates with the radio but never found a fix.

                                    kkanedaaK gohanG 2 Replies Last reply
                                    0
                                    • G GRDL

                                      I struggled with RPi gateway for ages without success. The easiest solution by far is to run the gateway on arduino and interface it to RPI through a serial gateway. Its not a very elegant solution but works. I did some investigation and came to the conclusion that the problem with RPi gateway is to do with the low level library that communicates with the radio but never found a fix.

                                      kkanedaaK Offline
                                      kkanedaaK Offline
                                      kkanedaa
                                      wrote on last edited by
                                      #19

                                      @grdl said in Cannot run MySensors on RPI 3:

                                      I struggled with RPi gateway for ages without success. The easiest solution by far is to run the gateway on arduino and interface it to RPI through a serial gateway. Its not a very elegant solution but works. I did some investigation and came to the conclusion that the problem with RPi gateway is to do with the low level library that communicates with the radio but never found a fix.

                                      Hi, thanks for your answer.

                                      If you are telling me that you have had the same issues as me, I am willing to do your method. True, not an elegant solution but I just want it to get up and running...

                                      When you say "run the gateway on arduino and interface it to RPI through a serial gateway", do you mean you built a serial gateway as mentioned here: https://www.mysensors.org/build/serial_gateway and then with an USB cable you connect it directly to your RPI? Am I understanding this correct?

                                      If yes, could you please tell me which parameters you have used while building your MySensors on your RPI. Would this be correct:

                                      ./configure --my-transport=nrf24 --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyMySensorsGateway

                                      Did you leave the value for --my-serial-pty was shown above? Did you add any other parameters?

                                      Sorry for asking so many questions but I cannot fully grasp the concept of MySensors without MQTT.

                                      I appreciate your response and thank you in advance :)

                                      1 Reply Last reply
                                      0
                                      • R Offline
                                        R Offline
                                        reinhold
                                        Hardware Contributor
                                        wrote on last edited by
                                        #20

                                        I've been running the Ethernet gateway (port 5003) on my raspi without issues for several months now.

                                        @kkanedaa It looks like the development version finally works with your nrf module. Regarding the MQTT connection refused: Are you sure your MQTT broker does not need a username and password?

                                        kkanedaaK 1 Reply Last reply
                                        0
                                        • G GRDL

                                          I struggled with RPi gateway for ages without success. The easiest solution by far is to run the gateway on arduino and interface it to RPI through a serial gateway. Its not a very elegant solution but works. I did some investigation and came to the conclusion that the problem with RPi gateway is to do with the low level library that communicates with the radio but never found a fix.

                                          gohanG Offline
                                          gohanG Offline
                                          gohan
                                          Mod
                                          wrote on last edited by
                                          #21

                                          @grdl on rpi3 is running fine, I have 2 radio modules too

                                          1 Reply Last reply
                                          0
                                          Reply
                                          • Reply as topic
                                          Log in to reply
                                          • Oldest to Newest
                                          • Newest to Oldest
                                          • Most Votes

                                          30

                                          Online

                                          11.7k

                                          Users

                                          11.2k

                                          Topics

                                          113.1k

                                          Posts


                                          Copyright 2025 TBD   |   Forum Guidelines   |   Privacy Policy   |   Terms of Service
                                          • Login
                                          • Don't have an account? Register
                                          • Login or register to search.
                                          • First post
                                            Last post
                                          0
                                          • MySensors
                                          • OpenHardware.io
                                          • Categories
                                          • Recent
                                          • Tags
                                          • Popular