Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

[SOLVED] Anyone a working example of the combination NewPing 1.9 and MySensors 2.2.0 ?

GertSanders Hardware Contributor 10 May 2018, 16:20 last edited by GertSanders 11 May 2018, 11:02

Does anyone have a working example of the combination NewPing 1.9 and MySensors 2.2.0 ?

I keep getting distance = 0, while the basic distance sensor sketch works perfectly (on the same setup), so the hardware side is OK.
Reply Quote 0
1 Reply Last reply 11 May 2018, 11:02
Loading More Posts
2
Posts

632
Views
Reply

Reply as topic
Log in to reply
GertSanders Hardware Contributor 11 May 2018, 11:02 last edited by @GertSanders

@gertsanders [SOLVED]: a wrong type in a declaration gave constant '0' values. Now corrected and distances is now measured correctly.
Reply Quote 0
1 Reply Last reply

2
Posts

632
Views

Log in to reply

1 out of 2

Suggested Topics

Arduino Celebrates 10 years (Malmö/Sweden)
Announcements • 29 Mar 2014, 17:08 • hek 29 Mar 2014, 17:08

1

0
Votes

1
Posts

3.3k
Views

No one has replied
Radio waking up for no reason.
Development • 4 Jul 2020, 21:09 • Sasquatch 15 Jan 2025, 08:33

3

0
Votes

3
Posts

37
Views

15 Jan 2025, 08:33

Over 4 years on, and my node ran continuously sending 4 messages every 5 minutes. It's 700mAh LiFePo4 battery voltage dropped from initial 3.45V to 3.24V, according to LiFePo4 voltge/SoC tables It's just under 40% left. 700*60% = 420mAh. 100 mAH per year. using library 2.40 and blob message I could cut usage to ~25mAh/year, not bad
PJON and Minicore not working
Development • 15 days ago • Trand 15 days ago

1

0
Votes

1
Posts

10
Views

No one has replied
Saving last known good state, but not in EEPROM
Development • 30 Jan 2024, 18:46 • OldSurferDude 15 Jan 2025, 08:51

6

0
Votes

6
Posts

33
Views

15 Jan 2025, 08:51

@OldSurferDude jus request counter states from controller on each reset, worked fine with Domoticz... or save in eeprom but increase location every write, on power up/reset search eeprom for largest value stored and carry on from that location, one long integer will fit 256 times in atmega328(p) eeprom, is that long enough for you ?
Adding Listen only device to my system.
Development • 26 Feb 2025, 00:39 • dpcons 26 Feb 2025, 06:26

5

0
Votes

5
Posts

19
Views

26 Feb 2025, 06:26

@mfalkvidd Thanks for the info!
Counting Incoming and Outgoing Messages from a Gateway
Development • 10 Dec 2024, 21:57 • Trand 14 Dec 2024, 20:23

3

1
Votes

3
Posts

25
Views

14 Dec 2024, 20:23

@mfalkvidd Thank you very much, that's exactly what I was looking for!

1
Online

11.5k
Users

11.1k
Topics

112.8k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1