Hello, thank you for your reply. You are right, it works fine without debug.

Thanks again

Hello @sundberg84,
I already considered this idea but my node have been running perfectly for two days before failed. So I think, power consideration are not the problem. I can trigg on and off my shutters many and many times without problem.

Hello all,

At the end, I choose to do a software reset every 24 hours. This solution is very bad for me but it works !!

bye

Hello @flopp ,

Sorry I was myself focus on this second problem that's interesting to solve too ?
At the end twice aren't solve !

Hello AWI,

Thanks for your reply, yes my node trigs 5 triacs. I use snubber, regulator, capacitor. And ond the other hand, all commands to the node work properly ? just battery level doesn't work and after several hours NRF24L01 stop to work.
I would like to reset NRF24L01 but with MySensors we don't have direct access to it anymore. Perhaps there is a way to reset the sketch globaly ?

thanks for your help

My real problem is not to send battery level. I try to do that because after 24 or 48 hours my node stop sending messages . So, I hoped that was a way to make it awake !

my loop(){}

// the loop routine runs over and over again forever:
void loop() {

  // Process incoming messages (like config from server)
  gw.process();  

  //---------------Lecture des ouvertures de porte------------------
  doorOpenOffState = digitalRead(HALLOFFICEDOOR); // lecture à chaque cycle (urgence)
  if (doorOpenOffState != doorOpenOffChange){
    gw.send(msgDoorOffice.setSensor(OFFICEDOOR).set(doorOpenOffState));
    doorOpenOffChange = doorOpenOffState;
  }

  doorOpenBedState = digitalRead(HALLBEDROOMDOOR); // lecture à chaque cycle (urgence)
  if (doorOpenBedState != doorOpenBedChange){
    gw.send(msgDoorBedroom.setSensor(BEDROOMDOOR).set(doorOpenBedState));
    doorOpenBedChange = doorOpenBedState;
  }
  
  if (digitalRead(ECLEXT) != oldInterExt){
    oldInterExt = !oldInterExt;
    eclState = !eclState;
    gw.send(msgLightSwitch.set(eclState));
  }

  //---------------Envoi du niveau de batterie !! pour rester eveillé------------------
  /*if ((millis() - myTime) > 10000) { // toutes les dix secondes
    myTime = millis();
    gw.sendBatteryLevel(97,1);
  } else {
    if ((millis() - myTime) < 0) {
      myTime = millis();
    }
  }*/
  gw.sendBatteryLevel(97,1);

// ---------------Traitement volet 1-----------------
  analogUpV1 = analogRead(UPV1);
  if ((analogUpV1 <25) && !manOnV1) { //analogUp proche de zéro et ancienne valeur niveau haut (en l'air)
    digitalWrite(TRIAC5, HIGH);
    digitalWrite(TRIAC2, LOW);
    triacTempoV1 = millis();
    triacManPriorityV1 = true;
    manOnV1 = true;
    memoStopV1 = false;
  } else {
    analogDownV1 = analogRead(DOWNV1);
    if ((analogDownV1 <25) && !manOnV1) { //proche de zéro
      digitalWrite(TRIAC5, LOW);
      digitalWrite(TRIAC2, HIGH);
      triacTempoV1 = millis();
      triacManPriorityV1 = true;
      manOnV1 = true;
      memoStopV1 = false;
    } else {
      if (analogUpV1 > 800 && analogDownV1 > 800 && !memoStopV1){ // les deux fils en l'air
        digitalWrite(TRIAC5, LOW);
        digitalWrite(TRIAC2, LOW);
        triacManPriorityV1 = false;
        manOnV1 = false;
        memoStopV1 = true;
      } else {
        if (!triacManPriorityV1){
          if (shutterOff1State && shutterOff2State) {
            shutterOff1State = false;
            shutterOff2State = false;
            digitalWrite(TRIAC5, LOW);
            digitalWrite(TRIAC2, LOW);
          } else {
            if (shutterOff1State) {
              shutterOff1State = false;
              digitalWrite(TRIAC5, HIGH);
              digitalWrite(TRIAC2, LOW);
              triacTempoV1 = millis();
            } else {
              if (shutterOff2State) {
                shutterOff2State = false;
                digitalWrite(TRIAC5, LOW);
                digitalWrite(TRIAC2, HIGH);
                triacTempoV1 = millis();
              }
            }
          }
        }
      }
    }
  }
  if (((triacTempoV1 + TEMPOOPENV1) < millis())) {
    digitalWrite(TRIAC5, LOW);
    digitalWrite(TRIAC2, LOW);
    triacManPriorityV1 = false;
  }

// --------------------------Traitement volet 2------------------------
  analogUpV2 = analogRead(UPV2);
  if ((analogUpV2 <25) && !manOnV2) { //analogUp proche de zéro et ancienne valeur niveau haut (en l'air)
    digitalWrite(TRIAC3, HIGH);
    digitalWrite(TRIAC4, LOW);
    triacTempoV2 = millis();
    triacManPriorityV2 = true;
    manOnV2 = true;
    memoStopV2 = false;
  } else {
    analogDownV2 = analogRead(DOWNV2);
    if ((analogDownV2 <25) && !manOnV2) { //proche de zéro
      digitalWrite(TRIAC3, LOW);
      digitalWrite(TRIAC4, HIGH);      
      triacTempoV2 = millis();
      triacManPriorityV2 = true;
      manOnV2 = true;
      memoStopV2 = false;
    } else {
      if (analogUpV2 > 800 && analogDownV2 > 800 && !memoStopV2){ // les deux fils en l'air
        digitalWrite(TRIAC3, LOW);
        digitalWrite(TRIAC4, LOW);        
        //triac3 = false;
        //triac4 = false;
        triacManPriorityV2 = false;
        manOnV2 = false;
        memoStopV2 = true;
      } else {
        if (!triacManPriorityV2){
          if (shutterBed1State && shutterBed2State) {
            shutterBed1State = false;
            shutterBed2State = false;
            digitalWrite(TRIAC3, LOW);
            digitalWrite(TRIAC4, LOW);            
          } else {
            if (shutterBed1State) {
              shutterBed1State = false;
              digitalWrite(TRIAC3, HIGH);
              digitalWrite(TRIAC4, LOW);              
              triacTempoV2 = millis();
            } else {
              if (shutterBed2State) {
                shutterBed2State = false;
                digitalWrite(TRIAC3, LOW);
                digitalWrite(TRIAC4, HIGH);                
                triacTempoV2 = millis();
              }
            }
          }
        }
      }
    }
  }
  if (((triacTempoV2 + TEMPOOPENV2) < millis())) {
    digitalWrite(TRIAC3, LOW);
    digitalWrite(TRIAC4, LOW);      
    triacManPriorityV2 = false;
  }
}

hello,
here is logs from gateway

2;4;1;1;3;70;0;3;0;9;send: 0-0-2-2 s=4,c=1,t=3,pt=0,l=1,sg=0,st=fail:7
Finished
0;0;3;0;18;PINGFinished
2;4;1;1;3;70;0;3;0;9;send: 0-0-2-2 s=4,c=1,t=3,pt=0,l=1,sg=0,st=fail:7
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=0,pt=1,l=1,sg=0:97
0;0;3;0;9;send: 0-0-1-1 s=255,c=3,t=0,pt=1,l=1,sg=0,st=ok:97
1;255;3;0;0;97
Finished
0;0;3;0;18;PING0;0;3;0;9;read: 65-65-0 s=255,c=3,t=0,pt=1,l=1,sg=0:99
0;0;3;0;9;send: 0-0-65-65 s=255,c=3,t=0,pt=1,l=1,sg=0,st=fail:99
65;255;3;0;0;99
0;0;3;0;9;read: 1-1-0 s=255,c=3,t=0,pt=1,l=1,sg=0:97
0;0;3;0;9;send: 0-0-1-1 s=255,c=3,t=0,pt=1,l=1,sg=0,st=ok:97
1;255;3;0;0;97
Finished

Is there a documentation to understand better ?

thanks

hello @AWI,

is there a way to verify if my sensor send a newx value ? because I can't use terminal with debug informations, I use Rx / Tx for an other purpose !

thanks

Hello @flopp,

I'll try this evening to remove all the code but gw.sendbattery...
I think there isn't problem with { or }, perhaps you don't like my way to write code

thanks

hello,

thanks for your answer. For me 97,1 means 97% and acknowledge. And the same code work properly with my other nodes with temperature sensors !

Any other ideas ?