battery level doesn't appear ?
-
my loop(){}
// the loop routine runs over and over again forever: void loop() { // Process incoming messages (like config from server) gw.process(); //---------------Lecture des ouvertures de porte------------------ doorOpenOffState = digitalRead(HALLOFFICEDOOR); // lecture à chaque cycle (urgence) if (doorOpenOffState != doorOpenOffChange){ gw.send(msgDoorOffice.setSensor(OFFICEDOOR).set(doorOpenOffState)); doorOpenOffChange = doorOpenOffState; } doorOpenBedState = digitalRead(HALLBEDROOMDOOR); // lecture à chaque cycle (urgence) if (doorOpenBedState != doorOpenBedChange){ gw.send(msgDoorBedroom.setSensor(BEDROOMDOOR).set(doorOpenBedState)); doorOpenBedChange = doorOpenBedState; } if (digitalRead(ECLEXT) != oldInterExt){ oldInterExt = !oldInterExt; eclState = !eclState; gw.send(msgLightSwitch.set(eclState)); } //---------------Envoi du niveau de batterie !! pour rester eveillé------------------ /*if ((millis() - myTime) > 10000) { // toutes les dix secondes myTime = millis(); gw.sendBatteryLevel(97,1); } else { if ((millis() - myTime) < 0) { myTime = millis(); } }*/ gw.sendBatteryLevel(97,1); // ---------------Traitement volet 1----------------- analogUpV1 = analogRead(UPV1); if ((analogUpV1 <25) && !manOnV1) { //analogUp proche de zéro et ancienne valeur niveau haut (en l'air) digitalWrite(TRIAC5, HIGH); digitalWrite(TRIAC2, LOW); triacTempoV1 = millis(); triacManPriorityV1 = true; manOnV1 = true; memoStopV1 = false; } else { analogDownV1 = analogRead(DOWNV1); if ((analogDownV1 <25) && !manOnV1) { //proche de zéro digitalWrite(TRIAC5, LOW); digitalWrite(TRIAC2, HIGH); triacTempoV1 = millis(); triacManPriorityV1 = true; manOnV1 = true; memoStopV1 = false; } else { if (analogUpV1 > 800 && analogDownV1 > 800 && !memoStopV1){ // les deux fils en l'air digitalWrite(TRIAC5, LOW); digitalWrite(TRIAC2, LOW); triacManPriorityV1 = false; manOnV1 = false; memoStopV1 = true; } else { if (!triacManPriorityV1){ if (shutterOff1State && shutterOff2State) { shutterOff1State = false; shutterOff2State = false; digitalWrite(TRIAC5, LOW); digitalWrite(TRIAC2, LOW); } else { if (shutterOff1State) { shutterOff1State = false; digitalWrite(TRIAC5, HIGH); digitalWrite(TRIAC2, LOW); triacTempoV1 = millis(); } else { if (shutterOff2State) { shutterOff2State = false; digitalWrite(TRIAC5, LOW); digitalWrite(TRIAC2, HIGH); triacTempoV1 = millis(); } } } } } } } if (((triacTempoV1 + TEMPOOPENV1) < millis())) { digitalWrite(TRIAC5, LOW); digitalWrite(TRIAC2, LOW); triacManPriorityV1 = false; } // --------------------------Traitement volet 2------------------------ analogUpV2 = analogRead(UPV2); if ((analogUpV2 <25) && !manOnV2) { //analogUp proche de zéro et ancienne valeur niveau haut (en l'air) digitalWrite(TRIAC3, HIGH); digitalWrite(TRIAC4, LOW); triacTempoV2 = millis(); triacManPriorityV2 = true; manOnV2 = true; memoStopV2 = false; } else { analogDownV2 = analogRead(DOWNV2); if ((analogDownV2 <25) && !manOnV2) { //proche de zéro digitalWrite(TRIAC3, LOW); digitalWrite(TRIAC4, HIGH); triacTempoV2 = millis(); triacManPriorityV2 = true; manOnV2 = true; memoStopV2 = false; } else { if (analogUpV2 > 800 && analogDownV2 > 800 && !memoStopV2){ // les deux fils en l'air digitalWrite(TRIAC3, LOW); digitalWrite(TRIAC4, LOW); //triac3 = false; //triac4 = false; triacManPriorityV2 = false; manOnV2 = false; memoStopV2 = true; } else { if (!triacManPriorityV2){ if (shutterBed1State && shutterBed2State) { shutterBed1State = false; shutterBed2State = false; digitalWrite(TRIAC3, LOW); digitalWrite(TRIAC4, LOW); } else { if (shutterBed1State) { shutterBed1State = false; digitalWrite(TRIAC3, HIGH); digitalWrite(TRIAC4, LOW); triacTempoV2 = millis(); } else { if (shutterBed2State) { shutterBed2State = false; digitalWrite(TRIAC3, LOW); digitalWrite(TRIAC4, HIGH); triacTempoV2 = millis(); } } } } } } } if (((triacTempoV2 + TEMPOOPENV2) < millis())) { digitalWrite(TRIAC3, LOW); digitalWrite(TRIAC4, LOW); triacManPriorityV2 = false; } }@flylowgofast
Look ok -
hello,
here is logs from gateway2;4;1;1;3;70;0;3;0;9;send: 0-0-2-2 s=4,c=1,t=3,pt=0,l=1,sg=0,st=fail:7 Finished 0;0;3;0;18;PINGFinished 2;4;1;1;3;70;0;3;0;9;send: 0-0-2-2 s=4,c=1,t=3,pt=0,l=1,sg=0,st=fail:7 0;0;3;0;9;read: 1-1-0 s=255,c=3,t=0,pt=1,l=1,sg=0:97 0;0;3;0;9;send: 0-0-1-1 s=255,c=3,t=0,pt=1,l=1,sg=0,st=ok:97 1;255;3;0;0;97 Finished 0;0;3;0;18;PING0;0;3;0;9;read: 65-65-0 s=255,c=3,t=0,pt=1,l=1,sg=0:99 0;0;3;0;9;send: 0-0-65-65 s=255,c=3,t=0,pt=1,l=1,sg=0,st=fail:99 65;255;3;0;0;99 0;0;3;0;9;read: 1-1-0 s=255,c=3,t=0,pt=1,l=1,sg=0:97 0;0;3;0;9;send: 0-0-1-1 s=255,c=3,t=0,pt=1,l=1,sg=0,st=ok:97 1;255;3;0;0;97 FinishedIs there a documentation to understand better ?
thanks
@flylowgofast for information on the logs take a look at the debug topic
-
My real problem is not to send battery level. I try to do that because after 24 or 48 hours my node stop sending messages . So, I hoped that was a way to make it awake !
-
My real problem is not to send battery level. I try to do that because after 24 or 48 hours my node stop sending messages . So, I hoped that was a way to make it awake !
@flylowgofast From what I read from your sketch you seem to do some high voltage / current switching. Especially the radio doesn't like all kinds of electronic disturbances (emc etc.) To avoid lockups you need to pay special attention/separate power supplies (if you haven't done already).
-
Hello AWI,
Thanks for your reply, yes my node trigs 5 triacs. I use snubber, regulator, capacitor. And ond the other hand, all commands to the node work properly ? just battery level doesn't work and after several hours NRF24L01 stop to work.
I would like to reset NRF24L01 but with MySensors we don't have direct access to it anymore. Perhaps there is a way to reset the sketch globaly ?thanks for your help
-
My real problem is not to send battery level. I try to do that because after 24 or 48 hours my node stop sending messages . So, I hoped that was a way to make it awake !
@flylowgofast said:
My real problem is not to send battery level. I try to do that because after 24 or 48 hours my node stop sending messages . So, I hoped that was a way to make it awake !
It would have been nice if you had wrote this in your first post.:disappointed:
So everyone could focus on the main problem -
Hello @flopp ,
Sorry I was myself focus on this second problem that's interesting to solve too ?
At the end twice aren't solve ! :disappointed: -
Hello all,
At the end, I choose to do a software reset every 24 hours. This solution is very bad for me but it works !!
bye
-
@flylowgofast One simple thing can be to move the radio away a bit and see if that helps. Its as AWI said probably interferance power-radio.
-
@flylowgofast One simple thing can be to move the radio away a bit and see if that helps. Its as AWI said probably interferance power-radio.
Hello @sundberg84,
I already considered this idea but my node have been running perfectly for two days before failed. So I think, power consideration are not the problem. I can trigg on and off my shutters many and many times without problem.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login