F
Hi guys I got a problem I just change ISP today and I decide to open the port 8080 to access my domoticz via internet but I just find out my ISP don't allow to open any ports is a double Nat. Already call support and there's nothing they can do , my question is you guys know any other way to portforwarding on a rpi. Any software. vpn or something else, i can use paid or free,
Thanks in advanced
Hi guys i building a multi sensor node , but i have one problem with a water pressure it keeps giving me a weather pressure , any one know what im doing wrong
#define MY_NODE_ID 1
#define MY_DEBUG
#define MY_RADIO_NRF24
#include <SPI.h>
#include <MySensors.h>
#define CHILD_ID_VOLT_1 1
#define CHILD_ID_VOLT_2 2
#define CHILD_ID_VOLT_3 3
#define CHILD_ID_CURRENT_1 4
#define CHILD_ID_CURRENT_2 5
#define CHILD_ID_CURRENT_3 6
#define CHILD_ID_PRESION 7
#define VOLT_SENSOR_ANALOG_PIN_1 0
#define VOLT_SENSOR_ANALOG_PIN_2 1
#define VOLT_SENSOR_ANALOG_PIN_3 2
#define CURRENT_SENSOR_ANALOG_PIN_1 3
#define CURRENT_SENSOR_ANALOG_PIN_2 4
#define CURRENT_SENSOR_ANALOG_PIN_3 5
#define PressPin A6
unsigned long SLEEP_TIME = 20000; // Sleep time between reads (in milliseconds)
MyMessage msg(CHILD_ID_VOLT_1, V_VOLTAGE);
MyMessage msg2(CHILD_ID_VOLT_2, V_VOLTAGE);
MyMessage msg3(CHILD_ID_VOLT_3, V_VOLTAGE);
MyMessage msg4(CHILD_ID_CURRENT_1, V_CURRENT);
MyMessage msg5(CHILD_ID_CURRENT_2, V_CURRENT);
MyMessage msg6(CHILD_ID_CURRENT_3, V_CURRENT);
MyMessage pressureMsg(CHILD_ID_PRESION, V_PRESSURE);
float lastVolt1;
float lastVolt2;
float lastVolt3;
float lastCurrent1;
float lastCurrent2;
float lastCurrent3;
float lastPresion;
int pressure = 0;
float PSI = 0;
float PSI_CAL = 2.0; // Calibration of sensor
int PSImsb = 0;
int PSIr = 0;
void before() {
}
void presentation()
{
sendSketchInfo("Pozo multi sensor", "1.0"); // Send the sketch version information to the gateway and Controller
present(CHILD_ID_VOLT_1, S_MULTIMETER); // Register this device as power sensor
present(CHILD_ID_VOLT_2, S_MULTIMETER); // Register this device as power sensor
present(CHILD_ID_VOLT_3, S_MULTIMETER); // Register this device as power sensor
present(CHILD_ID_CURRENT_1, S_MULTIMETER); // Register this device as power sensor
present(CHILD_ID_CURRENT_2, S_MULTIMETER); // Register this device as power sensor
present(CHILD_ID_CURRENT_3, S_MULTIMETER); // Register this device as power sensor
present(CHILD_ID_PRESION, S_WATER); // Register this device as power sensor
}
void setup()
{
}
void loop()
{
int Voltaje1 = analogRead(A0);
int Voltaje2 = analogRead(A1);
int Voltaje3 = analogRead(A2);
int Corriente1 = analogRead(A3);
int Corriente2 = analogRead(A4);
int Corriente3 = analogRead(A5);
float VoltLevel1 = map(Voltaje1,0,1023,0,500);
float VoltLevel2 = map(Voltaje2,0,1023,0,500);
float VoltLevel3 = map(Voltaje3,0,1023,0,500);
float CorrienteLevel1 = map(Corriente1,0,1023,0,200);
float CorrienteLevel2 = map(Corriente2,0,1023,0,200);
float CorrienteLevel3 = map(Corriente3,0,1023,0,200);
Serial.print("Voltaje L1: ");
Serial.println(VoltLevel1);
Serial.print("Voltaje L2: ");
Serial.println(VoltLevel2);
Serial.print("Voltaje L3: ");
Serial.println(VoltLevel3);
Serial.print("Corriente L1: ");
Serial.println(CorrienteLevel1);
Serial.print("Corriente L2: ");
Serial.println(CorrienteLevel2);
Serial.print("Corriente L3: ");
Serial.println(CorrienteLevel3);
//sensor de voltaje
if (VoltLevel1 != lastVolt1) {
send(msg.set(VoltLevel1, 1));
lastVolt1 = VoltLevel1;
}
if (VoltLevel2 != lastVolt2) {
send(msg2.set(VoltLevel2, 1));
lastVolt2 = VoltLevel2;
}
if (VoltLevel3 != lastVolt3) {
send(msg3.set(VoltLevel3, 1));
lastVolt3 = VoltLevel3;
}
//sensor de corriente
if (CorrienteLevel1 != lastCurrent1) {
send(msg4.set(CorrienteLevel1, 1));
lastCurrent1 = CorrienteLevel1;
}
if (CorrienteLevel2 != lastCurrent2) {
send(msg5.set(CorrienteLevel2, 1));
lastCurrent2 = CorrienteLevel2;
}
if (CorrienteLevel3 != lastCurrent3) {
send(msg6.set(CorrienteLevel3, 1));
lastCurrent3 = CorrienteLevel3;
}
/* ************************************************ */
pressure = analogRead (PressPin) ; // junk read
wait(25);
/* • Output: 0.5V – 4.5V linear voltage output. 0 psi outputs 0.5V, 50 psi outputs 2.5V, 100 psi outputs 4.5V
0 psi = .33v after scalling 5.0v to 3.3v
50 psi = 1.65v
100 psi = 2.97v
3.3v/1024 = .0032266 volt per bit
*/
pressure = analogRead (PressPin) ;
if (pressure < 106) pressure = 106; // this is minimum of .5v
PSI = (pressure - 106 ) * .1246; // where did we get this?? was .119904
PSI = PSI + PSI_CAL; // adjustment
PSImsb = PSI * 100;
PSIr = PSImsb % 100;
send(pressureMsg.set(PSI, 2)); // Send water pressure to gateway
Serial.print("Presion: ");
Serial.println(PSI);
wait(200);
// end of if (SLEEP_MODE || (cu
sleep(SLEEP_TIME);
}
any help will be very appreciated
And a few days later my pcb's arrived
Now to test the next version
well this is my project , right now im using 2 arduino nano with ethernet shield to read 3 lines Voltage on a delta instalation , 3 current sensors of 300amps for a motor , and 1 water pressure ,
all conected to a raspberry pi with domoticz
but yesterday i decide to change all , instead of 2 uno i will use a pro mini with a nrf24
so i desing two pcb
some code
#define MY_NODE_ID 100
#define MY_DEBUG
#define MY_RADIO_NRF24
#include <SPI.h>
#include <MySensors.h>
#define CHILD_ID_VOLT_1 1
#define CHILD_ID_VOLT_2 2
#define CHILD_ID_VOLT_3 3
#define CHILD_ID_CURRENT_1 4
#define CHILD_ID_CURRENT_2 5
#define CHILD_ID_CURRENT_3 6
#define CHILD_ID_PRESION 7
#define VOLT_SENSOR_ANALOG_PIN_1 0
#define VOLT_SENSOR_ANALOG_PIN_2 1
#define VOLT_SENSOR_ANALOG_PIN_3 2
#define CURRENT_SENSOR_ANALOG_PIN_1 3
#define CURRENT_SENSOR_ANALOG_PIN_2 4
#define CURRENT_SENSOR_ANALOG_PIN_3 5
#define PressPin A6
unsigned long SLEEP_TIME = 20000; // Sleep time between reads (in milliseconds)
MyMessage msg(CHILD_ID_VOLT_1, V_VOLTAGE);
MyMessage msg2(CHILD_ID_VOLT_2, V_VOLTAGE);
MyMessage msg3(CHILD_ID_VOLT_3, V_VOLTAGE);
MyMessage msg4(CHILD_ID_CURRENT_1, V_CURRENT);
MyMessage msg5(CHILD_ID_CURRENT_2, V_CURRENT);
MyMessage msg6(CHILD_ID_CURRENT_3, V_CURRENT);
MyMessage pressureMsg(CHILD_ID_PRESION, V_PRESSURE);
float lastVolt1;
float lastVolt2;
float lastVolt3;
float lastCurrent1;
float lastCurrent2;
float lastCurrent3;
float lastPresion;
int pressure = 0;
float PSI = 0;
float PSI_CAL = 2.0; // Calibration of sensor
int PSImsb = 0;
int PSIr = 0;
void before() {
}
void presentation()
{
sendSketchInfo("Multisensor", "1.7"); // Send the sketch version information to the gateway and Controller
present(CHILD_ID_VOLT_1, S_MULTIMETER); // Register this device as power sensor
present(CHILD_ID_VOLT_2, S_MULTIMETER); // Register this device as power sensor
present(CHILD_ID_VOLT_3, S_MULTIMETER); // Register this device as power sensor
present(CHILD_ID_CURRENT_1, S_MULTIMETER); // Register this device as power sensor
present(CHILD_ID_CURRENT_2, S_MULTIMETER); // Register this device as power sensor
present(CHILD_ID_CURRENT_3, S_MULTIMETER); // Register this device as power sensor
present(CHILD_ID_PRESION, S_WATER); // Register this device as power sensor
}
void setup()
{
}
void loop()
{
int Voltaje1 = analogRead(A0);
int Voltaje2 = analogRead(A1);
int Voltaje3 = analogRead(A2);
int Corriente1 = analogRead(A3);
int Corriente2 = analogRead(A4);
int Corriente3 = analogRead(A5);
float VoltLevel1 = map(Voltaje1,0,1023,0,500);
float VoltLevel2 = map(Voltaje2,0,1023,0,500);
float VoltLevel3 = map(Voltaje3,0,1023,0,500);
float CorrienteLevel1 = map(Corriente1,0,1023,0,200);
float CorrienteLevel2 = map(Corriente2,0,1023,0,200);
float CorrienteLevel3 = map(Corriente3,0,1023,0,200);
Serial.print("Voltaje L1: ");
Serial.println(VoltLevel1);
Serial.print("Voltaje L2: ");
Serial.println(VoltLevel2);
Serial.print("Voltaje L3: ");
Serial.println(VoltLevel3);
Serial.print("Corriente L1: ");
Serial.println(CorrienteLevel1);
Serial.print("Corriente L2: ");
Serial.println(CorrienteLevel2);
Serial.print("Corriente L3: ");
Serial.println(CorrienteLevel3);
//sensor de voltaje
if (VoltLevel1 != lastVolt1) {
send(msg.set(VoltLevel1, 1));
lastVolt1 = VoltLevel1;
}
if (VoltLevel2 != lastVolt2) {
send(msg2.set(VoltLevel2, 1));
lastVolt2 = VoltLevel2;
}
if (VoltLevel3 != lastVolt3) {
send(msg3.set(VoltLevel3, 1));
lastVolt3 = VoltLevel3;
}
//sensor de corriente
if (CorrienteLevel1 != lastCurrent1) {
send(msg4.set(CorrienteLevel1, 1));
lastCurrent1 = CorrienteLevel1;
}
if (CorrienteLevel2 != lastCurrent2) {
send(msg5.set(CorrienteLevel2, 1));
lastCurrent2 = CorrienteLevel2;
}
if (CorrienteLevel3 != lastCurrent3) {
send(msg6.set(CorrienteLevel3, 1));
lastCurrent3 = CorrienteLevel3;
}
/* ************************************************ */
pressure = analogRead (PressPin) ; // junk read
wait(25);
/* • Output: 0.5V – 4.5V linear voltage output. 0 psi outputs 0.5V, 50 psi outputs 2.5V, 100 psi outputs 4.5V
0 psi = .33v after scalling 5.0v to 3.3v
50 psi = 1.65v
100 psi = 2.97v
3.3v/1024 = .0032266 volt per bit
*/
pressure = analogRead (PressPin) ;
if (pressure < 106) pressure = 106; // this is minimum of .5v
PSI = (pressure - 106 ) * .1246; // where did we get this?? was .119904
PSI = PSI + PSI_CAL; // adjustment
PSImsb = PSI * 100;
PSIr = PSImsb % 100;
send(pressureMsg.set(PSI, 2)); // Send water pressure to gateway
Serial.print("Presion: ");
Serial.println(PSI);
wait(200);
// end of if (SLEEP_MODE || (cu
sleep(SLEEP_TIME);
}
havent tested with sensors yet
but looks good so far
thanks guys , the solution for me was to add
ln -s /dev/ttyMySensorsGateway /dev/ttyUSB020
to rc.local
but i will try your idea @mfalkvidd thanks for the help
hi guys i just make a new controller with a raspberry pi and domoticz , now im trying to add the serial gateway to my domoticz , but in order to domoticz to open the port i need to open ssh connection and use
sudo ./bin/mysgw
for domoticz to read the port /dev/ttyUSB020 , if i dont use ./bin/mysgw the log just said
2019-04-21 04:31:58.747 Status: MySensors: Using serial port: /dev/ttyUSB020
2019-04-21 04:31:58.747 Error: MySensors: Error opening serial port!
, what im missing here
just do the standar installaton
./configure --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyMySensorsGateway
make
sudo make install
sudo systemctl enable mysgw.service
sudo ln -s /dev/ttyMySensorsGateway /dev/ttyUSB020
i dont know what im missing here, thanks for the help
Guys you are right is too early to quit , i have to try the RFM69 433Mhz as well before quitting , i was planning to wire my house with a 5v power supply to power all the sensors but i guess using a lower freq can help me to avoid that , will give it a try , lest just hope the rfm69 arrive, cuz i always have problems with evay ,
thanks guys you open mi mind one more time
Hello guys i just decide to quit using mysensors , in nothing personal is just is not working for me i live in mexico and almost all houses are a Faraday cages, yesterday i was tenting a new gateway with a few sensors and i just lose my mind , losing connection , every minute , try adding a repeater didnt help change the NRF24L01+ radio for a long range antenna , changing arduinos mini /nano/ uno etc , same result all day yesterday i was fighting to use mysensors , today i just went ahead and buy a nodemcu install mqtt to my controller , flash tasmota and in less than 2 hours i was able to add my sensor , i love this community, thanks to you guys i was introduced to home automation and learn a lot , but is time for me to change for another solutions for my home ,
thanks guys i really appreciate all your help , and all you time spending on working on an open source solution for all of us ,
@neverdie go for the pi zero chip is really nice a little better than the pi zero wifi and bt integraded 4gb and a few cool stuff , but theres people that pay a year ago and still waiting for the chip to arrive , no reply and no support on forum , to me chip is dying , you cant never go wrong with a pi , but i will try in a few months the omega2 to remplace my chips
well today finally i decide to change to c.h.i.p. as a controller with domoticz an amazing device but too bad for the product that got really bad customer support, ( if you planning to buy a c.h.i.p. read the forum first to get all the problems)
this is my controller using a chip, arduino nano
planing to chage the nano to a nodemcu
@Dave-Myers this is asoweme will try in this days but sound amazing thanks for sharing.
Your idea is possible you need a good case for that meaby a pelican case with clear top for the solar cell
Something like this
http://www.ebay.com/itm/Pelican-1050-Solid-Black-Micro-Case-with-Free-engraved-nameplate-/231011576632?hash=item35c95ceb38:g:BDIAAOxyrxZR1xrC
Solar panel
Ypou need a good silicone for any hole you drill on the box and I this this will be able to do what you need
almost a year ago i was browsing on kickstarter when i saw the new micro pc C.H.I.P. from Next Thing Co. (www.getchip.com) , i order one just for fun 9usd + 6usd shipping , this machine took too long to arrive almost a year ,
but when arrive i get amazed of all the fetures that this $9 machine can do
1GHz Allwinner R8 processor
512MB of RAM
8GBytes of flash
Wifi
Bluetooth 4.0
video output (composite video)
linux debian distribution
CHIP is powered at 5V and draws about 500mA during boot,On the header terminals, we find a variety of power sources include 5V, 3.3V and 1.8V. The maximum current draws on these are 2A, 700mA and 50mA respectively
already included with a connector for a battery ( 1s) with " sudo battery.sh "we can have battery stats
BAT_STATUS=0
CHARG_IND=1
BAT_EXIST=1
CHARGE_CTL=0xc9
CHARGE_CTL2=0x45
Battery voltage = 3951.2mV
Battery discharge current = 0mA
Battery charge current = 510.0mA
Internal temperature = 56.8c
so i decide to make a controller for my sensors as i dont had a pi (to expensive for me :( )
so i decide to install mycontroller (mycontroller.org) it works pretty well but i decide to use Domoticz the installation for domoticz is pretty simple
sudo apt-get update
sudo apt-get upgrade
sudo apt-get install build-essential nano cmake git libboost-dev libboost-thread-dev libboost-system-dev libsqlite3-dev curl libcurl4-openssl-dev libssl-dev libusb-dev zlib1g-dev python3-dev
mkdir ~/domoticz
cd ~/domoticz
wget https://releases.domoticz.com/releases/release/domoticz_linux_armv7l.tgz
tar xvfz domoticz_linux_armv7l.tgz
rm domoticz_linux_armv7l.tgz
./domoticz
and thats it
http://chip-ip:8080
domoticz is really nice controller i gonna test it for a couple of months.
also we can install node-red and johnny-five gpio for chip
sudo apt-get update
sudo apt-get upgrade
sudo apt-get install build-essential
sudo apt-get install python
cd /tmp
mkdir node
cd node
wget https://nodejs.org/dist/v4.4.7/node-v4.4.7-linux-armv7l.tar.xz
tar -xvf node*
cd node*
sudo cp -R * /usr/local
cd /usr/local/bin
cd ~
mkdir node-red
cd node-red
npm install node-red
cd node_modules
cd node-red
npm install node-red-contrib-gpio johnny-five chip-io
node red.js
Go to http://chip-ip:1880 and play
i test node-red and works great
if you know how to use a pi you will know how to use chip
on the chip forum danjperron manage to add a nrf24l01 to the chip se meaby we can use a controller and gateway in the same device or make wifi sensors
https://bbs.nextthing.co/t/success-nrf24l01-on-spi-works/7919
@mfalkvidd thanks mate that's exactly what I need
@Boots33 I did on Firefox ( window) and in chrome ( android) same result on both , I just need to wait don't know how long till the "You have exceeded the maximum number of registration attempts for this session. Please try again later." Allow me to try again.
Hey guys I need your help to understand the combining of sketch
I'm current using the air humidity sketch and I love to add more sketch like the battery level sketch
Any one got already une that can share so I can understand the needed part to do other combinations
I using arduino for a automatic aquarium controller and I will love to implement it to my sensor but I need to understand more about the code and libraries
If anyone can share a example of two combined sketch I can go forward to my project , small steps at the time lol
Thanks guys
Any admin from the domoticz forum or moderator?
I been trying for days to register to the forum of domoticz but I'm unable to do so
Always the registration confirmation give me the error.
"You have incorrectly sorted the items to the correct list of the confirmation question.
You have exceeded the maximum number of registration attempts for this session. Please try again later."
And I can't find any email to contact the domoticz's team or a kind user to inform a moderator or admin if there's is a problem with the registration form
Thanks guys for you help
Really nice icons thanks for sharing
@vikasjee glady but I follow some one else steps lol
https://bbs.nextthing.co/t/domoticz-small-how-to/2585
But instead of
wget http://domoticz.sourceforge.net/beta/domoticz_linux_armv7l.tgz
Just use
Wget https://releases.domoticz.com/releases/beta/domoticz_linux_armv7l.tgz