Posts made by SparkAndHale

Same here. I had to go up to 5V to power my Arduino Pro Mini 3.3V sufficiently.

@hek Yes, I look into that and send a pull request as soon as there is a prototype.

Dear @hek, yes it does have 11kb eeprom . http://www.arduino.cc/en/ArduinoCertified/IntelGalileo
If that is similar to AVR, I don't know. Also, this implementation of the eeprom interface is all capital: ```

#include <EEPROM.h>

I tried all programmer options in Arduino, like AVR ISP, AVRISP MKII, etc...

The Intel Pentium ISA SOC is not a ATMEL AVR-like chip. I assume that is the reason why taking this eeprom.h header file will not work - since the Intel SOC is base on a 32-Bit architecture.

@hek shouldn't we try to implement the standard Arduino EEPROM in the mysensors.h header (and pgmspace.h and wdt.h? Or ought we think about a MySensors version for Intel Galileo 32BIT SOC chips?

Hi all,

I installed Arduino IDE 1.6.3 and copied all the library files over to the Arduino library as shown in this video. http://www.mysensors.org/build/ (I omited the libs which are already in place).

I can upload and run successfully the Arduino Blink sketch to my Intel Galileo Gen2. Good so far.

When I load and attempt to upload the MySensors example "SerialGateway", it fails with the following message.

In file included from SAHSerialGateway.ino:16:0:
C:\Program Files (x86)\Arduino\libraries\MySensors/MySensor.h:19:24: fatal error: avr/eeprom.h: No such file or directory
compilation terminated.
Error compiling.

What is the root folder of where this eeprom.h file should be placed? Apparently the MySensor header file requires it.

Any one else is having this problem with a new setup?

I looking with a magnifying glass at the chip, i noted that this is NOT NRF24L01+ but just a NRF24L01 without the plus.

I used this smaller versions and they worked immediately. I_GATEWAY_READY message appeared. http://www.ebay.com/itm/2-4G-NRF24L01-PA-LNA-Wireless-Module-with-Ceramic-Antenna-1-27mm-/400746941364?pt=LH_DefaultDomain_0&hash=item5d4e610bb4

MySensors did post a warning on that: http://forum.mysensors.org/topic/728/radio-setup-give-check-wires/16

THREAD RESOLVED.

Yes. That's the case. I meant one needs to set the BAUD in the Arduino IDE Serial Monitor.

I do NOT need to wire the Nano any different with the NRF24L01+ than the Arduino Pro Mini, right? http://www.mysensors.org/build/connect_radio

THREAD RESOLVED: CHINESE SUPPLIER DID SEND WRONG RADIO MODULE: NRF24L01 instead of NRF24L01+
Do not buy from ebay-member alice1101983. They send NRF24L01 instead of NRF24L01+.

Hi, I'm using a Arduino Nano v3 as recommended for my Serial Gateway. I hooked up the radio module as described (http://www.mysensors.org/build/connect_radio) and I simply want to send a message from the Serial Monitor (either Arduino IDE 1.6 or CodeBender).

Subsequently I copied the MySensors SerialGateway.ino from the example repository. See here: https://github.com/mysensors/Arduino/blob/master/libraries/MySensors/examples/SerialGateway/SerialGateway.ino

I disable all the gw variables since I only want to test the serial input with serialEvent(). That works! I go ahead and remove the comment characters in front of the gw variables. Recompile and upload. Now the messages are not retrieved and never outputed on the Serial Monior Screen. I also selected the NewLine Argument in the drop down box. No success.

Why is gw.beginn() having that influence on that serial input/output?

I tested if the radio LEDs (TX,RX,ERR) indicate something. They fully light up as if there would be constant communication.
The only thing I get when I startup (and change to baud rate 115200 in the serial monitor) is: 0;0;3;0;9;check wires. Well that is an indicator! But I DONT want to wire them any other than recommended here: http://www.mysensors.org/build/connect_radio
Or is the wireing for the Arduino Nano different from the Arduino Pro Mini?

Any clue why that serial gateway cannot read from the serial COM port when gw.beginn() is invoked?

This is my code:

#include <SPI.h>  
#include <MySensor.h>  
#include <MyGateway.h>  
#include <stdarg.h>

#define INCLUSION_MODE_TIME 1 // Number of minutes inclusion mode is enabled
#define INCLUSION_MODE_PIN 3 // Digital pin used for inclusion mode button


MyGateway gw(DEFAULT_CE_PIN, DEFAULT_CS_PIN, INCLUSION_MODE_TIME, INCLUSION_MODE_PIN,  6, 5, 4);

char inputString[MAX_RECEIVE_LENGTH] = "";    // A string to hold incoming commands from serial/ethernet interface
int inputPos = 0;
boolean commandComplete = false;  // whether the string is complete

void setup()  
{ 
   //Set Auto by MySensonsrs
   //Serial.begin(115200);
  gw.begin();
}

void loop()  
{ 
  gw.processRadioMessage();   
  if (commandComplete) {
    // A command wass issued from serial interface
    // We will now try to send it to the actuator
    Serial.println(inputString);
    gw.parseAndSend(inputString);
    commandComplete = false;  
    inputPos = 0;
  }
}
/*
  SerialEvent occurs whenever a new data comes in the
 hardware serial RX.  This routine is run between each
 time loop() runs, so using delay inside loop can delay
 response.  Multiple bytes of data may be available.
 */
void serialEvent() {
  while (Serial.available()) {
    // get the new byte:
    char inChar = (char)Serial.read(); 
    // if the incoming character is a newline, set a flag
    // so the main loop can do something about it:
    Serial.println(inChar);
    if (inputPos<MAX_RECEIVE_LENGTH-1 && !commandComplete) { 
      if (inChar == '\n') {
        inputString[inputPos] = 0;
        commandComplete = true;
      } else {
        // add it to the inputString:
        inputString[inputPos] = inChar;
        inputPos++;
      }
    } else {
       // Incoming message too long. Throw away 
        inputPos = 0;
    }
  }
}