Quick thought did you factory reset the max! devices before trying to pair? I found mine wouldn't work until they had been reset due to the pairing with the cube.
Posts made by twisted
-
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
-
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
Sorry on the road ATM, but will look when i get home. Here is some pics of my wiring I have on my phone in case that is some use.
-
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
it should be families select 4 I believe, did you go into the max.conf and uncomment all the lines under ti cc1101 module? you may need to set gpio to 25 (not 23) and don't uncomment the the additional section. Reboot, then you should see 4 max! when "sudo homegear -r", "ls"
-
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
@Stuart-Middleton attached is an example of the items that get loaded when connected to openhab2 via homegear and the homematic binding.
-
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
@Stuart-Middleton Although I mentioned my difficulties, I would suggest that you at least have a look at homegear and openhab (or the openhabian bundle to make it easier) as it does give great access to the devices and opens up very easy use of MQTT.
-
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
FYI, I bought a CC1101 connected it up to an RPI, setup openhab, homegear, the homeatic binding, and within minutes I had all of the devices listed and complete control over them all. Well I can say that is where it has ended, I am struggling to either find pre-written logic or writing my own to control everything. The issue isn't so much writing it as such, but choosing which system should host it. This dilemma exists, as I have everything else in my vera, I am getting into node-red, and now also have openhab/homegear in the loop, I don't want to fracture my set up too much from a control interface point. I like the idea of keeping the WAF where it is, so I will probably still need to have some sort of control via the vera and therefore one of the apps that the other half is still happy with.
-
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
I'm having a small issue, and I can't see why. I had to reload and now every time I try to load it I get the following before it terminates. This is from fresh install.
Traceback (most recent call last):
File "main.py", line 204, in <module>
Main()
File "main.py", line 96, in init
self.doLoop()
File "main.py", line 111, in doLoop
buttonCheckHeat("main")
File "/home/pi/PiHeating/heatinggpio.py", line 173, in buttonCheckHeat
MaxInterface().checkHeat(0)
File "/home/pi/PiHeating/max.py", line 56, in checkHeat
self.switchHeat()
File "/home/pi/PiHeating/max.py", line 486, in switchHeat
roomTemps = CreateUIPage().createRooms()
File "/home/pi/PiHeating/webui.py", line 224, in createRooms
actualTemp, roomOpen, roomMode)
UnboundLocalError: local variable 'roomOpen' referenced before assignment -
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
I have to say using Vera and the boiler switch attached to that is a great solution, if I could just get past one problem. I wonder if anyone else is experiencing this, but I find the time taken for the valves to respond to the temperature changes is a little slow. Lets say I set the required temperature to 19c most rooms jump to 20/21 before the valves close enough to actually prevent further heating to the room.
My thoughts at the moment are to see if I can somehow directly communicate with the valves or maybe set offsets for each temp on the valves so they read a couple of degrees high.
Anyone have any thoughts?
-
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
Just saw the explanation txt appear, thank you so much, it means I can double check what I set was correct.
Funnily I noticed as it just appeared when I was searching the code to work out a couple of bits. -
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
After many delays and other items got in the way I finally have almost sully working system. I do have one issue I am struggling with and that is that I can't seem to turn the boiler off once the temperatures have been met.
Also is there any way some of the configuration page could be clarified as there are a number of options I am a little unsure about.
Thanks
-
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
At the moment nodered is still at my limit of knowledge, but I am getting there. In the end I went with a dual channel SSR302 from secure. To be honest if I needed to do it again, I would probably just use a twin relay z-wave module.
-
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
So, I finally got most of my bits and I have this up and running. This is quite simply awesome, but tbh I am now looking to see if there is some way to get this into node-red. I could be wrong but I am starting to see my home automation fracture into multiple different systems and my original plan was to try and keep everything to one interface where possible. Therefore I am starting to see node-red as maybe being my glue between each of them, the benefit of this is I might be able to drag in emoncms and better data analysis.
-
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
Just an update, I hope my kit will be delivered by the end of the month now, so very much looking forward to trying this out! Thanks for all your hard work.
-
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
My system is not that close, but I am in the process of getting the eq-3 ordered from conrad. I am planning on the following:
A cube gateway
Start with 7 thermostat heads (non +)
Not sure if I need the wall mount thermostats as they don't look wife friendly and was thinking about putting a mysensors temp sensor in each room.I held off getting a device to switch my heating and water as I wasn't sure the best route, so far I have considered:
Secure dual channel zwave.
fibaro dual relay
custom home made.I liked the idea of the horst dual channel as it automatically shuts down if the signal controlling it doesn't 'phone home' every, IIRC 20min.
Still not sure though as I need something bullet proof to make it wife friendly.Thanks for the posting of you work I am just trying to go through it now.
-
RE: Boiler control from MAX! Cube to Drayton Boiler via Raspberry Pi/Vera/Mysensors.
@stephenmhall Wow, wow, wow.
So you may have just solved my issue with heating controls. I have been evaluating a number of heating solutions and somehow the MAX! slipped by. Although without your work here I'm not sure I would have the ability to get this far. I was sat patiently waiting (IIRC last summer) for heat genius to make their API available, but even then the cost was very high and would mean me doubling up on some sensors around the house.
I would be over the moon if you were happy to share your work here, as I am tempted to buy a set to get me started tonight although I may just wait for your reply in case you have any suggestions. (btw I'm in the UK).I will wait excitedly for more info. thank you.
-
RE: ESP8266 MySensors Gateway Crashes when Node Connects
Well I'm sort of glad, I thought I was the only one with this issue. I have tried numerous power supplies, including one I am sure is very stable and can supply the required load.
I am using 1.5.
-
RE: ESP8266 (ESP-201) endless reboot
I had a very similar issue, and managed to resolve it by following the quoted process found in the below link (please note I have a ESP8266-12E & it worked for me but do not guarantee it is the solution for all).:
https://github.com/esp8266/Arduino/issues/95#issuecomment-96399149
*** ROOT ISSUE - ESPTool.exe is NOT correctly erasing flash, allows module to get "borked" and is then "unborkable".
Above wall of text can be summarized as "sometimes on windows modules get to a state where uploads stop working", and many people suggest many different hardware-related fixes. They didn't work for me, and simply grabbing the esptool.py script and running:
F:\Users\timm\Documents\Arduino\PythonESPTool>python esptool.py --port COM5 --baud 76800 erase_flash
put the module back into an uploadable state.
Manually asking esptool.exe to erase the module did not work.... so esptool.exe as packaged here has a bug wrt erasing that esptool.py doesn't.So - for all other frustrated windows users, if you bork your module and it stops working, do the following until this bug is fixed:
install Python2.7 (google for instructions)
download esptool.py from this git distro into a local directory (hope this link keeps working - https://github.com/themadinventor/esptool, I could not find in this GIT repo)
open a command window in the same directory and run "python esptool.py --port COM5 --baud 76800 erase_flash"
use your IDE to download your prev sketch, should now work again.
I'm going to try to diddle the platform.txt file to use this instead of the esptool.exe, if it is easy I'll report back.
This may be hard to reproduce, if I find a sketch that consistently breaks esptool.exe I will share, but please comment IF this approach helps you out of a "stuck" module so the smart guys (Ivan, looking at you) can prioritize and look into whether it's worth fixing/replacing esptool.exe. -
RE: My sensorboard MYS 1.0beta
As above, if possible and still available I would like 5 boards too. Thanks
-
RE: One Arduino with multiple functions
Just be careful and check each additional sensor as you add it. I wasted a lot of time fault finding something I would have found easily if I had tested one at a time. FYI I so far have combined quite a few different things successfully, but still struggle with the humidity and relays together for some reason.