MQTT Support

[alowhum]

I've tried to add the required code. But as I'm not an MQTT user, I'm not sure I've implemented it properly.

You mentioned:
It should be asking for the mqtt server address, credentials and topic prefix?

• The IP address can be filled in at the same spot where you fill it in for the ethernet gateway.
• Are credentials required?
• Topic prefix seems to be hardcoded to the mysensors ones? Right now I have:

                MQTTC = MQTT(ip_address, 1883, 60)
                MQTTC.start()
                
                #self.GATEWAY = mysensors.AsyncMQTTGateway(ip_address, event_callback=self.mysensors_message, 
                #    persistence=True, persistence_file=self.persistence_file_path, 
                #    protocol_version='2.2')
                
                self.GATEWAY = mysensors.AsyncMQTTGateway(MQTTC.publish, MQTTC.subscribe, in_prefix='mygateway1-out',
                    out_prefix='mygateway1-in', retain=True, event_callback=event,
                    persistence=True, persistence_file=self.persistence_file_path, 
                    protocol_version='2.2')

[mfalkvidd]

@alowhum on a MySensors mqtt gateway, username, password and topic prefix can be configured by defines. Since they are configurable on a MySensors gateway, I think it would make sense to also support configuration of these parameters in Webthings gateway.

[alowhum]

I've added support for username and password (in theory). It should be available in the next version.

[alowhum]

I've been trying to test it. I got to the point where in theory it's connected to Mosquitto. But I don't have any MySensors MQTT devices, so nothing is happening after that.

Could someone help me craft a test message? Something like:

mosquitto_pub -h localhost -t mygateway1-out -m "4;255;3;0;6;0"

[mfalkvidd]

@alowhum I don't use mqtt either, but https://www.mysensors.org/build/mqtt_gateway#setup-and-test-gateway has instructions for how to send a test message. Can you use that?

[bjacobse]

I don't use Webthings, but MQTT shall work similar, on my RPI I have Domoticz and Mosquitto broker running, check in a prompt:
Is the broker running? ps -ef |grep mosq
you can also check the logfile: sudo tail /var/log/mosquitto/mosquitto.log

Then if above is ok, then your test message shall appear in the logfile, then Mosquitto is working. Then next check Mosquitto WebThings connection. I would assume a logfile must be present in WebThings that shows if a sensor is providing something

[bjacobse]

@bjacobse
did you setup Node-RED?
Maybe this can help you: https://diyprojects.io/mqtt-mosquitto-communicating-connected-objects-iot/#.XTBAKiZJFCU

[Ryanmt]

I don't have webthings setup anymore but am happy to spin it up in a docker container and test for you. Just let me know what the steps are to install the test version and i'll give it a go.

[alowhum]

@Ryanmt thanks, that would be great.

I've tried to do some testing. Things look promising.

The Paho MQTT client seems to connect to a lot of topics:

Started MQTT client
subscribing to topicmygateway1-out/+/+/0/+/+
subscribing to topicmygateway1-out/+/+/3/+/+
subscribing to topicmygateway1-out/7/1/1/+/+
subscribing to topicmygateway1-out/7/1/2/+/+
subscribing to topicmygateway1-out/7/10/1/+/+
subscribing to topicmygateway1-out/7/10/2/+/+
subscribing to topicmygateway1-out/7/11/1/+/+
subscribing to topicmygateway1-out/7/11/2/+/+

etc.

Then, this:
mosquitto_pub -t 'mygateway1-out/7/1/2/0/47' -m '0,test'
gives:
Not a valid message: not a valid value for dictionary value @ data['payload']

So there is a communication path. I'm just not recreating the correct message.

[alowhum]

Does this look correct?
in_prefix='mygateway1-out', out_prefix='mygateway1-in'

Shouldn't that be reversed?

[alowhum]

I saw the same pattern in the original example code at PyMySensors, so I'm assuming it's ok.

I've uploaded version 0.1.2 of the MySensors add-on, Mozilla should accept it in a work day or two.