💬 Capacitive Soil Moisture Sensor
-
Hi great design... If I can suggest one improvement, it would be to burn a minicore bootloader and set BOD to 1.8V so that the batteries can last longer.
-
Hi great design... If I can suggest one improvement, it would be to burn a minicore bootloader and set BOD to 1.8V so that the batteries can last longer.
@Puneit-Thukral Thanks. I am not quite sure, so correct me please if I am wrong, but I think I am already using the MiniCore bootloader with platformIO. Or do I need to configure to explicitly use the MiniCore bootloaders? Also I have set BOD to disabled as I read somewhere that no BOD can also save battery.
-
Hi great design... If I can suggest one improvement, it would be to burn a minicore bootloader and set BOD to 1.8V so that the batteries can last longer.
@Puneit-Thukral but will the peripherals still work at that level? No use to lower the BOD if radio/security/sensors stop working at a higher voltage.
Do you feel secure today? No? Start requiring some signatures and feel better tomorrow ;)
-
@Puneit-Thukral but will the peripherals still work at that level? No use to lower the BOD if radio/security/sensors stop working at a higher voltage.
-
@Anticimex That was also my thinking behind that. According to the datasheet the ATmega328P works reliably down to 2.4V when using 8MHz.
@Ron @Anticimex The radio stops at 1.9V.. so I think its fair to do a BOD of 1.8V.
I used arduinoAsISP to burn bootloader and this is my platformio.ini
[env:program_via_ArduinoISP] platform = atmelavr framework = arduino ; Serial bootloader protocol upload_protocol = custom ; Serial upload port upload_port = /dev/cu.* ; Get upload baud rate defined in the fuses_bootloader environment upload_speed = 19200 board_build.f_cpu = 8000000L board_hardware.oscillator = internal board_hardware.uart = uart0 board_hardware.bod = 1.8v board_hardware.eesave = yes board_hardware.ckout = no upload_flags = -C ; use "tool-avrdude-megaavr" for the atmelmegaavr platform /Users/puneit/Nextcloud/PlatformIO/bootloader/tool-avrdude/avrdude2.conf -p $BOARD_MCU -P $UPLOAD_PORT -b $UPLOAD_SPEED -c stk500 upload_command = avrdude $UPLOAD_FLAGS -U flash:w:$SOURCE:i -
@Ron @Anticimex The radio stops at 1.9V.. so I think its fair to do a BOD of 1.8V.
I used arduinoAsISP to burn bootloader and this is my platformio.ini
[env:program_via_ArduinoISP] platform = atmelavr framework = arduino ; Serial bootloader protocol upload_protocol = custom ; Serial upload port upload_port = /dev/cu.* ; Get upload baud rate defined in the fuses_bootloader environment upload_speed = 19200 board_build.f_cpu = 8000000L board_hardware.oscillator = internal board_hardware.uart = uart0 board_hardware.bod = 1.8v board_hardware.eesave = yes board_hardware.ckout = no upload_flags = -C ; use "tool-avrdude-megaavr" for the atmelmegaavr platform /Users/puneit/Nextcloud/PlatformIO/bootloader/tool-avrdude/avrdude2.conf -p $BOARD_MCU -P $UPLOAD_PORT -b $UPLOAD_SPEED -c stk500 upload_command = avrdude $UPLOAD_FLAGS -U flash:w:$SOURCE:i@Puneit-Thukral yes but for full/specified function, atsha, atmega and any sensor circuitry also need to be operational at that level.
-
@Ron @Anticimex The radio stops at 1.9V.. so I think its fair to do a BOD of 1.8V.
I used arduinoAsISP to burn bootloader and this is my platformio.ini
[env:program_via_ArduinoISP] platform = atmelavr framework = arduino ; Serial bootloader protocol upload_protocol = custom ; Serial upload port upload_port = /dev/cu.* ; Get upload baud rate defined in the fuses_bootloader environment upload_speed = 19200 board_build.f_cpu = 8000000L board_hardware.oscillator = internal board_hardware.uart = uart0 board_hardware.bod = 1.8v board_hardware.eesave = yes board_hardware.ckout = no upload_flags = -C ; use "tool-avrdude-megaavr" for the atmelmegaavr platform /Users/puneit/Nextcloud/PlatformIO/bootloader/tool-avrdude/avrdude2.conf -p $BOARD_MCU -P $UPLOAD_PORT -b $UPLOAD_SPEED -c stk500 upload_command = avrdude $UPLOAD_FLAGS -U flash:w:$SOURCE:i@Puneit-Thukral When I tested a recent node the radio was presenting to the GW all the way down to 1.64V - so it is always worth trying to see if it works for you or not (ebyte red module).
-
Nice work @Ron . Thinking about getting some of these for my plants.
Any experienced issues, or the PCB and components works good?Controller: Proxmox VM - Home Assistant
MySensors GW: Arduino Uno - W5100 Ethernet, Gw Shield Nrf24l01+ 2,4Ghz
MySensors GW: Arduino Uno - Gw Shield RFM69, 433mhz
RFLink GW - Arduino Mega + RFLink Shield, 433mhz -
Nice work @Ron . Thinking about getting some of these for my plants.
Any experienced issues, or the PCB and components works good?@sundberg84 said in 💬 Capacitive Soil Moisture Sensor:
Nice work @Ron . Thinking about getting some of these for my plants.
Any experienced issues, or the PCB and components works good?I had the first prototype running for about 2-3 months and did not experience any issues. The next thing on my todo list is to get an estimation on the total battery lifetime. I would assume that it will be quite good as I did not notice any significant drop in battery voltage over that time. I will post my measurements in the corresponding GitHub question as soon as I have some time. :)
-
@Ron said in 💬 Capacitive Soil Moisture Sensor:
@Puneit-Thukral Thanks. I am not quite sure, so correct me please if I am wrong, but I think I am already using the MiniCore bootloader with platformIO. Or do I need to configure to explicitly use the MiniCore bootloaders? Also I have set BOD to disabled as I read somewhere that no BOD can also save battery.
hi
I'm not sure, but I believe I'm already using the MiniCore bootloader with platformIO. Please tell me if I'm incorrect. Is it necessary to set the MiniCore bootloaders explicitly?
