ESP8266Wifi Gateway won't connect

OldSurferDude

OldSurferDude

@hard-shovel client worked for me, too. That is, it sent the message "2.3.2" to topic "mygateway1-outx/0/255/0/0/18"

OldSurferDude

@hard-shovel I tried the client and it did indeed send the MySensors version message. But it does not pass along the messages from the Arduino nodes.

hard-shovel

@OldSurferDude have you set the MQTT user and MQTT passwords in the sketch and uncommented them as well?

// Enable these if your MQTT broker requires usenrame/password
//#define MY_MQTT_USER "username"
//#define MY_MQTT_PASSWORD "password"

// Enable these if your MQTT broker requires usenrame/password
#define MY_MQTT_USER "MQTTusername2022"
#define MY_MQTT_PASSWORD "MQTTpassword2022"

what does your debug log look like?
This sample is not connected correctly to the MQTT Broker

10:33:26.151 -> dhcp client start...
10:33:26.151 -> 341 TSM:INIT:GW MODE
10:33:26.199 -> 364 TSM:READY:ID=0,PAR=0,DIS=0
10:33:26.199 -> 396 MCO:REG:NOT NEEDED
10:33:26.339 -> 505 GWT:TPC:CONNECTING...
10:33:27.365 -> 1533 MCO:BGN:STP
10:33:27.365 -> 1551 MCO:BGN:INIT OK,TSP=1
10:33:27.412 -> 1579 TSM:READY:NWD REQ
10:33:27.412 -> 1606 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
10:33:28.671 -> scandone
10:33:35.993 -> pm open,type:2 0
10:33:44.664 -> 18861 TSF:MSG:READ,254-254-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
10:33:44.758 -> 18924 TSF:MSG:BC
10:33:44.758 -> 18942 TSF:MSG:FPAR REQ,ID=254
10:33:44.804 -> 18973 TSF:PNG:SEND,TO=0
10:33:44.804 -> 18998 TSF:CKU:OK
10:33:44.851 -> 19016 TSF:MSG:GWL OK
10:33:45.459 -> 19646 TSF:MSG:SEND,0-0-254-254,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
10:33:46.671 -> 20876 TSF:MSG:READ,254-254-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
10:33:46.766 -> 20939 TSF:MSG:PINGED,ID=254,HP=1
10:33:46.813 -> 20980 TSF:MSG:SEND,0-0-254-254,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
10:33:46.860 -> 21057 TSF:MSG:READ,254-254-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100

This is working correctly

10:36:34.908 -> dhcp client start...
10:36:37.655 -> ip:192.168.1.202,mask:255.255.255.0,gw:192.168.1.254
10:36:37.702 -> 7014 GWT:TPC:IP=192.168.1.202
10:36:37.702 -> 7100 GWT:RMQ:CONNECTING...
10:36:37.749 -> 7144 GWT:RMQ:OK
10:36:37.795 -> 7161 GWT:TPS:TOPIC=mygateway4-out/0/255/0/0/18,MSG SENT
10:36:44.792 -> pm open,type:2 0
10:38:56.629 -> 146027 TSF:MSG:READ,254-254-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
10:38:56.723 -> 146091 TSF:MSG:BC
10:38:56.723 -> 146109 TSF:MSG:FPAR REQ,ID=254
10:38:56.770 -> 146142 TSF:PNG:SEND,TO=0
10:38:56.770 -> 146168 TSF:CKU:OK
10:38:56.816 -> 146187 TSF:MSG:GWL OK
10:38:57.655 -> 147013 TSF:MSG:SEND,0-0-254-254,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
10:38:58.683 -> 148042 TSF:MSG:READ,254-254-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
10:38:58.730 -> 148105 TSF:MSG:PINGED,ID=254,HP=1
10:38:58.776 -> 148148 TSF:MSG:SEND,0-0-254-254,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
10:38:58.869 -> 148226 TSF:MSG:READ,254-254-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
10:38:58.916 -> 148294 TSF:MSG:SEND,0-0-254-254,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
10:38:59.010 -> 148375 TSF:MSG:READ,254-254-0,s=255,c=0,t=17,pt=0,l=11,sg=0:2.4.0-alpha
10:38:59.058 -> 148450 GWT:TPS:TOPIC=mygateway4-out/254/255/0/0/17,MSG SENT
10:38:59.151 -> 148515 TSF:MSG:READ,254-254-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0
10:38:59.197 -> 148578 GWT:TPS:TOPIC=mygateway4-out/254/255/3/0/6,MSG SENT
10:39:00.923 -> 150319 TSF:MSG:READ,254-254-0,s=255,c=3,t=11,pt=0,l=14,sg=0:MockMySensors 
10:39:01.017 -> 150398 GWT:TPS:TOPIC=mygateway4-out/254/255/3/0/11,MSG SENT
10:39:01.064 -> 150462 TSF:MSG:READ,254-254-0,s=255,c=3,t=12,pt=0,l=4,sg=0:v0.5
10:39:01.157 -> 150529 GWT:TPS:TOPIC=mygateway4-out/254/255/3/0/12,MSG SENT
10:39:01.949 -> 151337 TSF:MSG:READ,254-254-0,s=1,c=0,t=0,pt=0,l=12,sg=0:Outside Door
10:39:02.044 -> 151410 GWT:TPS:TOPIC=mygateway4-out/254/1/0/0/0,MSG SENT
10:39:02.091 -> 151471 TSF:MSG:READ,254-254-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
10:39:02.184 -> 151542 TSF:MSG:SEND,0-0-254-254,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
10:39:02.699 -> 152055 TSF:MSG:READ,254-254-0,s=255,c=3,t=0,pt=1,l=1,sg=0:83

OldSurferDude

@hard-shovel My MQTT broker does not require them. Should I uncomment and leave them blank?

hard-shovel

@OldSurferDude You should leave them commented if not required.

I have just tested with a new install on windows of mosquitto with config file for anonymous access and it is working fine with them commented out.

what do your gateway debug logs look like?

OldSurferDude

@hard-shovel This is what I'm getting (with no nodes connecting to gateway)

MCO:BGN:INIT GW,CP=RNNGE---,FQ=80,REL=255,VER=2.3.2
117 TSF:LRT:OK
133 TSM:INIT
147 TSF:WUR:MS=0
170 TSM:INIT:TSP OK
191 TSM:INIT:GW MODE
213 TSM:READY:ID=0,PAR=0,DIS=0
245 MCO:REG:NOT NEEDED
scandone
1322 GWT:TIN:CONNECTING...
2351 GWT:TIN:CONNECTING...
scandone
state: 0 -> 2 (b0)
4097 GWT:TIN:CONNECTING...
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 1
cnt

connected with Automation, channel 9
dhcp client start...
ip:192.168.1.30,mask:255.255.255.0,gw:192.168.1.193
4316 GWT:TIN:IP: 192.168.1.30
4355 GWT:TIN:ETH OK
4378 MCO:BGN:STP
4396 MCO:BGN:INIT OK,TSP=1
4424 TSM:READY:NWD REQ
4451 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
pm open,type:2 0

And this comes when a node connects:

197868 TSF:MSG:READ,2-2-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
197928 TSF:MSG:BC
197947 TSF:MSG:FPAR REQ,ID=2
197977 TSF:PNG:SEND,TO=0
198003 TSF:CKU:OK
198022 TSF:MSG:GWL OK
198460 TSF:MSG:SEND,0-0-2-2,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
200006 TSF:MSG:READ,2-2-0,s=255,c=3,t=24,pt=1,l=1,sg=0:1
200065 TSF:MSG:PINGED,ID=2,HP=1
200106 TSF:MSG:SEND,0-0-2-2,s=255,c=3,t=25,pt=1,l=1,sg=0,ft=0,st=OK:1
200244 TSF:MSG:READ,2-2-0,s=255,c=3,t=15,pt=6,l=2,sg=0:0100
200309 TSF:MSG:SEND,0-0-2-2,s=255,c=3,t=15,pt=6,l=2,sg=0,ft=0,st=OK:0100
200385 TSF:MSG:READ,2-2-0,s=255,c=0,t=17,pt=0,l=5,sg=0:2.3.2
200456 GWT:TSA:ETH OK
200481 TSF:MSG:READ,2-2-0,s=255,c=3,t=6,pt=1,l=1,sg=0:0
200545 GWT:TSA:ETH OK
202529 TSF:MSG:READ,2-2-0,s=255,c=3,t=11,pt=0,l=15,sg=0:BatMoistHumTemp
202611 GWT:TSA:ETH OK
202636 TSF:MSG:READ,2-2-0,s=255,c=3,t=12,pt=0,l=9,sg=0:     0.01
202710 GWT:TSA:ETH OK
202885 TSF:MSG:READ,2-2-0,s=0,c=0,t=35,pt=0,l=0,sg=0:
202948 GWT:TSA:ETH OK
203141 TSF:MSG:READ,2-2-0,s=1,c=0,t=7,pt=0,l=0,sg=0:
203203 GWT:TSA:ETH OK
203396 TSF:MSG:READ,2-2-0,s=2,c=0,t=6,pt=0,l=0,sg=0:
203458 GWT:TSA:ETH OK
203651 TSF:MSG:READ,2-2-0,s=3,c=0,t=30,pt=0,l=0,sg=0:
203713 GWT:TSA:ETH OK
203925 TSF:MSG:READ,2-2-0,s=255,c=3,t=26,pt=1,l=1,sg=0:2
203992 TSF:MSG:SEND,0-0-2-2,s=255,c=3,t=27,pt=1,l=1,sg=0,ft=0,st=OK:1
204128 TSF:MSG:READ,2-2-0,s=255,c=3,t=0,pt=1,l=1,sg=0:100
204199 GWT:TSA:ETH OK
204407 TSF:MSG:READ,2-2-0,s=3,c=1,t=38,pt=7,l=5,sg=0:6.52
204475 GWT:TSA:ETH OK
204542 TSF:MSG:READ,2-2-0,s=0,c=1,t=37,pt=2,l=2,sg=0:1023
204610 GWT:TSA:ETH OK

paqor

Hello have with the gateway constantly disconnects after a few days and I can only reactivate it by resetting on the gateway.

Have now inserted a separate power supply with a large electrolytic capacitor 5000 µF-let's see....

hard-shovel

@OldSurferDude You are getting regular GWT:TSA:ETH OK message which i do not and you have no
MSG SENT lines

Which MQTT broker are you using?

my test setup which i hope matches yours is:
MySensors 2.3.2 & ESP8266 core 2.7.4
ESP8266 Node MCU with sketch GatewayESP8266MQTTClient
MY_BAUD_RATE 9600
MY_MQTT_USER & MQTT_PASSWORD commented out
MY_CONTROLLER_IP_ADDRESS 192, 168, 1, 195 address of the MQTT broker
MY_CONTROLLER_URL_ADDRESS "MQTT-TEST-W10" commented out Use IP or URL not Both
MY_PORT 1883

MQTT Broker
Mosquitto 2.0.15 running as a service on a windows 10 machine
listener 1883 anonymous access
URL MQTT-TEST-W10

When connected to the MQTT Broker and receiving messages from a node the gateway shows

09:48:18.962 -> 718935 TSF:MSG:READ,254-254-0,s=1,c=1,t=16,pt=2,l=2,sg=0:0
09:48:19.010 -> 718997 GWT:TPS:TOPIC=mygateway5-out/254/1/1/0/16,MSG SENT

09:48:19.104 -> 719059 TSF:MSG:READ,254-254-0,s=1,c=1,t=15,pt=1,l=1,sg=0:1
09:48:19.149 -> 719121 GWT:TPS:TOPIC=mygateway5-out/254/1/1/0/15,MSG SENT

09:48:19.198 -> 719182 TSF:MSG:READ,254-254-0,s=255,c=3,t=0,pt=1,l=1,sg=0:83
09:48:19.292 -> 719246 GWT:TPS:TOPIC=mygateway5-out/254/255/3/0/0,MSG SENT

if a message is sent to the broker the gateway shows

10:03:54.285 -> 1654209 GWT:IMQ:TOPIC=mygateway5-in/254/255/1/0/15, MSG RECEIVED
10:03:54.331 -> 1654279 TSF:MSG:SEND,0-0-254-254,s=255,c=1,t=15,pt=0,l=1,sg=0,ft=0,st=OK:1
10:03:54.423 -> 1654358 TSF:MSG:READ,254-254-0,s=1,c=1,t=16,pt=2,l=2,sg=0:1
10:03:54.471 -> 1654421 GWT:TPS:TOPIC=mygateway5-out/254/1/1/0/16,MSG SENT
10:03:54.565 -> 1654483 TSF:MSG:READ,254-254-0,s=1,c=1,t=15,pt=1,l=1,sg=0:1
10:03:54.611 -> 1654546 GWT:TPS:TOPIC=mygateway5-out/254/1/1/0/15,MSG SENT

OldSurferDude

@hard-shovel I created a faux nano sensor and used nRF24L01 channel 121 to communicate to the gateway. Here is my NodeMCU ESP8266 code with all comments taken out:

#define VER 0.4
#define MY_DEBUG true
#define MY_BAUD_RATE 9600
#define MY_RADIO_RF24
#define MY_RF24_CHANNEL 121
#define MY_GATEWAY_ESP8266 "Test"
#define MY_WIFI_SSID "SSID"
#define MY_WIFI_PASSWORD "pass"
#define MY_HOSTNAME "ESP8266_GW"
#define MY_MQTT_PUBLISH_TOPIC_PREFIX "mysensors-out"
#define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mysensors-in"
#define MY_PORT 1883
#define MY_GATEWAY_MAX_CLIENTS 8
#define MY_CONTROLLER_IP_ADDRESS 192, 168, 1, 142
#include <MySensors.h>
void setup() {Serial.print("ESP8266MySensorsGateway version: ");Serial.println(VER); }
void presentation(){}
void loop(){}

On boot, the gateway generates the following debug output:

60 MCO:BGN:INIT GW,CP=RNNGE---,FQ=80,REL=255,VER=2.3.2
118 TSF:LRT:OK
133 TSM:INIT
147 TSF:WUR:MS=0
170 TSM:INIT:TSP OK
191 TSM:INIT:GW MODE
213 TSM:READY:ID=0,PAR=0,DIS=0
246 MCO:REG:NOT NEEDED
scandone
1322 GWT:TIN:CONNECTING...
2350 GWT:TIN:CONNECTING...
scandone
state: 0 -> 2 (b0)
4097 GWT:TIN:CONNECTING...
state: 2 -> 3 (0)
state: 3 -> 5 (10)
add 0
aid 1
cnt 

connected with Automation, channel 9
dhcp client start...
ip:192.168.1.30,mask:255.255.255.0,gw:192.168.1.193
4316 GWT:TIN:IP: 192.168.1.30
4354 GWT:TIN:ETH OK
4376 MCO:BGN:STP
ESP8266MySensorsGateway version: 0.40
4394 MCO:BGN:INIT OK,TSP=1
4463 TSM:READY:NWD REQ
4490 ?TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=20,pt=0,l=0,sg=0,ft=0,st=OK:
6865 TSF:MSG:READ,2-2-0,s=0,c=1,t=37,pt=2,l=2,sg=0:208
6933 GWT:TSA:ETH OK

The faux node connects to the gateway indicated by this debug code from the gateway (which is repeated for each "reading" (eg. 204):

1047590 TSF:MSG:READ,2-2-0,s=0,c=1,t=37,pt=2,l=2,sg=0:204
1047656 GWT:TSA:ETH OK

Nothing arrives at the MQTT broker. From another machine, I can publish to the broker:

mosquitto_pub -h 192.168.1.139 -t test/mztake -m "did it arrive?"

and it does arrive at the broker.

What am I missing?

OSD

mfalkvidd

@OldSurferDude you are (at least) missing #define MY_GATEWAY_MQTT_CLIENT.

The sketch you are using is instructing MySensors to create an ethernet gateway.

Example sketch for esp8266 mqtt: https://github.com/mysensors/MySensors/blob/master/examples/GatewayESP8266MQTTClient/GatewayESP8266MQTTClient.ino

OldSurferDude

@mfalkvidd said in ESP8266Wifi Gateway won't connect:

#define MY_GATEWAY_MQTT_CLIENT

That was it! Thank you!

OSD

OldSurferDude

@mfalkvidd Because I see that the example has a presentation() routine with the comment "// Present locally attached sensors here" I made the assumption that the gateway could have local sensors. I described a local sensor

// local sensor information
#define MY_NODE_ID 3
#define CHILD_ID_GATEWAY_FAUX_SENSOR 0
MyMessage msgFauxSensor(CHILD_ID_GATEWAY_FAUX_SENSOR, V_LEVEL);
int fauxSensorValue = 0;

and put the data acquisition code in the loop:

// Send locally attached sensors data here
 send(msgFauxSensor.set(fauxSensorValue++));
 Serial.print("Value sent: ");Serial.println(fauxSensorValue);
 delay(30000);

Lo and Behold! This data was being found on the MQTT broker! Albeit the NODE_ID was not 3 as defined, but 0. This makes sense because the NODE_ID of the gateway is zero.

Previously, I had my gateway running on an RPi. My question is, can I put a presentation() routine and data acquisition of the gateway running on my RPi?

mfalkvidd

delay(30000);

A delay in the gateway will make the gateway freeze. It will not handle incoming messages (not from the mqtt broker, not for any nodes). Use wait() instead.

Previously, I had my gateway running on an RPi. My question is, can I put a presentation() routine and data acquisition of the gateway running on my RPi?

Yes, it should work. The file to edit is https://github.com/mysensors/MySensors/blob/development/examples_linux/mysgw.cpp

Have you forgotten about https://forum.mysensors.org/post/111806 ?

OldSurferDude

@mfalkvidd Yes, totally forgot about that link you put there. Thanks for reminding me. :)

ESP8266Wifi Gateway won't connect

13

12.0k

11.2k

113.4k