Rotary dimmer switch and mysensors?

[otto001]

Yes, thank you. Unfortunately this is not really useable. I have one wall rotary switch and connected it to an arduino directly. But the analogue in does not detect anything I am trying on the switch. I think the rotary encoder is working absolutely different to usual wall switches :-(

[rvendrame]

I'm not sure if I understood. Do you have an analog dimmer , connected somehow to arduino? Maybe if you post the circuit + sketch here someone can help...

[otto001]

Hi,

yes, I have a REV Dimmer Typ 13623 (http://www.rev.de/dzo/artikel/201/0077494_201.pdf?t=1342180610)
Just connected it to an arduino with some "configurable firmata" and as controller I am using fhem. This sketch is just reporting the status of the pins directly to the controller. I am using pin A0 for instance - if I connect it directly to GND, this is immediately reported to the controller. If I am connecting the dimmer, nothing happens. I hope I could explain what I am trying to do...

[AWI]

The link is not working for me. Is the dimmer a potentiometer ie variable resistor type? Can you share the schematic of the dimmer and connection?

[jemish]

I want to control ceiling fan using Rottery dimmer switch using arduino.
How can i use?

[otto001]

Sorry, this should work:

http://www.rev.de/dzo/artikel/201/007/7494_201.pdf?t=1342180610
Unfortunately it is German only...

[AWI]

@otto001 it looks like you are using a 230 volt thyristor/triac dimmer. These do not act as a resistor and therefore cannot be used to connect to the Arduino....
Maybe if you tell what you want to accomplish there is some help available

[hek]

@otto001 said:

http://www.rev.de/dzo/artikel/201/007/7494_201.pdf?t=1342180610

The knob could possibly be reused with a rotary encoder if you disassemble your dimmer. But it will be hard to squeeze in the necessary AC stuff + Arduino and radion behind the faceplate.

[otto001]

Thanks!
What I want to do is pretty simple: Just have a rotary dimmer connected to an arduino - the controller should get the values and dim the lights (connected to different devices) according to the rotary switch. But it should be a wall switch (to get a reliable WAF)....

[AWI]

@otto001 The "waf" of constructions is low... What works for me is momentary switch button dims with a "long press". These are widely available in all kinds of designs. Another option is to combine it with a touch sensor..

[otto001]

@AWI: Thanks for your hint. I am also thinking about switch buttons with long press. BTW: how did you implement the long press in mysensors?

[AWI]

@otto001 You can find an example in the "bounce2" library. Below an excerpt from a windowcover routine (nothing special for MySensors)

if ( buttonUp.update()){					// change in Up button
		if (buttonUp.read() == HIGH){			// release button
			buttUpstate = 0 ;
			Serial.println("Button UP released");
			if (calibrateCover != A_STOP){  	// calibrate end, set value
				calibrateCover = A_STOP;
				curPos = setPos = lastPos = 0 ; // Set the "UP" position (store in EEPROM and send to controller)
			}
		}
		else{									// press button, cover up
			buttUpstate = 1 ;
			Serial.println("Button UP pressed");
			buttUptime = millis(); 				// register change time
			if (curAction != A_STOP){			// cover is running, stop at current position and make "set"
				setPos = curPos;
			} else {
				setPos = 0;
			}
		}```

[otto001]

@AWI: thanks! will have a look at it!

[vladimir]

@otto001 Hello!
Did you manage to implement this node?