No protocol version during PRESENTATION

[Tang]

Hi

I just upgraded all my sensors/gateway to the new version and I don't see protocol version of my sensors during PRESENTATION message.
It worked before (1.4.1)
I compiled my sketches using master.zip file in download section

Here is full log of my controller (agocontrol) during temperature sensor startup:

 => 22:21:11 2015/08/05 RECEIVING: 0/0;INTERNAL;0;I_LOG_MESSAGE;read: 110-110-0 s=255,c=0,t=17,pt=0,l=3,sg=0:1.5
 => 22:21:11 2015/08/05 RECEIVING: 110/255;PRESENTATION;0;S_ARDUINO_NODE;1.5
 => 22:21:11 2015/08/05 RECEIVING: 0/0;INTERNAL;0;I_LOG_MESSAGE;read: 110-110-0 s=255,c=3,t=6,pt=1,l=1,sg=0:0
 => 22:21:11 2015/08/05 RECEIVING: 110/255;INTERNAL;0;I_CONFIG;0
 => 22:21:11 2015/08/05 SENDING: 110;255;3;0;6;M
 => 22:21:11 2015/08/05 RECEIVING: 0/0;INTERNAL;0;I_LOG_MESSAGE;send: 0-0-110-110 s=255,c=3,t=6,pt=0,l=1,sg=0,st=ok:M
 => 22:21:13 2015/08/05 RECEIVING: 0/0;INTERNAL;0;I_LOG_MESSAGE;read: 110-110-0 s=255,c=3,t=11,pt=0,l=18,sg=0:Temperature S
 => 22:21:13 2015/08/05 RECEIVING: 110/255;INTERNAL;0;I_SKETCH_NAME;Temperature Sensor
 => 22:21:13 2015/08/05 RECEIVING: 0/0;INTERNAL;0;I_LOG_MESSAGE;read: 110-110-0 s=255,c=3,t=12,pt=0,l=3,sg=0:1.0
 => 22:21:13 2015/08/05 RECEIVING: 110/255;INTERNAL;0;I_SKETCH_VERSION;1.0
 => 22:21:13 2015/08/05 RECEIVING: 0/0;INTERNAL;0;I_LOG_MESSAGE;read: 110-110-0 s=0,c=0,t=6,pt=0,l=0,sg=0:
 => 22:21:13 2015/08/05 RECEIVING: 110/0;PRESENTATION;0;S_TEMP;

As you can see S_ARDUINO_NODE reports (line2) its version 1.5 but the S_TEMP presentation (last line) reports nothing in payload.
The only sensor that reports correctly its version is the repeater node.

Here is my sketch:

#include <MySensor.h>  
#include <SPI.h>
#include <DallasTemperature.h>
#include <OneWire.h>

#define TIMEOUT 600000 //10 minutes
#define ONE_WIRE_BUS 4 // Pin where dallase sensor is connected 
unsigned long SLEEP_TIME = 150000; // Sleep time between reads (in milliseconds)
OneWire oneWire(ONE_WIRE_BUS);
DallasTemperature sensors(&oneWire);
MySensor gw;
// Initialize temperature message
MyMessage msg(0,V_TEMP);

void setup()  
{ 
  // Startup OneWire 
  sensors.begin();

  // Startup and initialize MySensors library. Set callback for incoming messages. 
  gw.begin(); 

  // Send the sketch version information to the gateway and Controller
  gw.sendSketchInfo("Temperature Sensor", "1.0");
  
  gw.present(0, S_TEMP);

}

void loop()     
{     
  // Process incoming messages (like config from server)
  gw.process();

  // Fetch and round temperature to one decimal
  float temperature = static_cast<float>(static_cast<int>(sensors.getTempCByIndex(0)) * 10.) / 10.;
  sensors.requestTemperatures(); 
  
  gw.send(msg.set(temperature,1));
      
  //sleep
  gw.sleep(SLEEP_TIME);
}

Is this an issue or I missed something?

Thank you for your help.

Tang

[hek]

gw.present(0, S_TEMP);

Version is only sent to the S_ARDUINO_NODE now.

The present() method now supports a 3rd argument, a device title which will show instead of version if controller supports it.

E.g. gw.present(0, S_TEMP, "Temp Living Room");

[Tang]

Ok thanks for the precision