message for V_tripped

[chdid]

Hello,

I use this code for detect water leak.

/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * DESCRIPTION
 *
 * Interrupt driven binary switch example with dual interrupts
 * Author: Patrick 'Anticimex' Fallberg
 * Connect one button or door/window reed switch between 
 * digitial I/O pin 3 (BUTTON_PIN below) and GND and the other
 * one in similar fashion on digital I/O pin 2.
 * This example is designed to fit Arduino Nano/Pro Mini
 * 
 */


#include <MySensor.h>
#include <SPI.h>

#define SKETCH_NAME "Debordement Eau"
#define SKETCH_MAJOR_VER "1"
#define SKETCH_MINOR_VER "0"

#define PRIMARY_CHILD_ID 3
#define SECONDARY_CHILD_ID 4

#define PRIMARY_BUTTON_PIN 2   // Arduino Digital I/O pin for button/reed switch
#define SECONDARY_BUTTON_PIN 3 // Arduino Digital I/O pin for button/reed switch

#if (PRIMARY_BUTTON_PIN < 2 || PRIMARY_BUTTON_PIN > 3)
#error PRIMARY_BUTTON_PIN must be either 2 or 3 for interrupts to work
#endif
#if (SECONDARY_BUTTON_PIN < 2 || SECONDARY_BUTTON_PIN > 3)
#error SECONDARY_BUTTON_PIN must be either 2 or 3 for interrupts to work
#endif
#if (PRIMARY_BUTTON_PIN == SECONDARY_BUTTON_PIN)
#error PRIMARY_BUTTON_PIN and BUTTON_PIN2 cannot be the same
#endif
#if (PRIMARY_CHILD_ID == SECONDARY_CHILD_ID)
#error PRIMARY_CHILD_ID and SECONDARY_CHILD_ID cannot be the same
#endif
 
MySensor sensor_node;

// Change to V_LIGHT if you use S_LIGHT in presentation below
MyMessage msg(PRIMARY_CHILD_ID, V_TRIPPED);
MyMessage msg2(SECONDARY_CHILD_ID, V_TRIPPED);

int oldValue=-1;
int oldValue2=-1;

void setup()  
{  
  sensor_node.begin();

  // Setup the buttons
  pinMode(PRIMARY_BUTTON_PIN, INPUT );
  pinMode(SECONDARY_BUTTON_PIN, INPUT);

  // Activate internal pull-ups
  digitalWrite(PRIMARY_BUTTON_PIN, HIGH);
  digitalWrite(SECONDARY_BUTTON_PIN, HIGH);
  
  // Send the sketch version information to the gateway and Controller
  sensor_node.sendSketchInfo(SKETCH_NAME, SKETCH_MAJOR_VER"."SKETCH_MINOR_VER);

  // Register binary input sensor to sensor_node (they will be created as child devices)
  // You can use S_DOOR, S_MOTION or S_LIGHT here depending on your usage. 
  // If S_LIGHT is used, remember to update variable type you send in. See "msg" above.
  sensor_node.present(PRIMARY_CHILD_ID, S_WATER_LEAK);  
  sensor_node.present(SECONDARY_CHILD_ID, S_WATER_LEAK);  
}

// Loop will iterate on changes on the BUTTON_PINs
void loop() 
{
  
  // Alway process incoming messages whenever possible
  sensor_node.process();
  
  int value;

  // Short delay to allow buttons to properly settle
  //sensor_node.wait(5);
  
  value = digitalRead(PRIMARY_BUTTON_PIN);
  
  if (value != oldValue) {
     // Value has changed from last transmission, send the updated value
     sensor_node.send(msg.set(value==HIGH ? 1 : 0));
     
     oldValue = value;
  }

  value = digitalRead(SECONDARY_BUTTON_PIN);
  
  if (value != oldValue2) {
     // Value has changed from last transmission, send the updated value
     sensor_node.send(msg2.set(value==HIGH ? 1 : 0));
     oldValue2 = value;
  }
 
  // Sleep until something happens with the sensor
  sensor_node.sleep(PRIMARY_BUTTON_PIN-2, CHANGE, SECONDARY_BUTTON_PIN-2, CHANGE, 0);
}

But the value received with sensor_node.send(msg.set(value==HIGH ? 1 : 0)); are not 0 or 1 but 1073741824 or 1073741825.

What is wrong ?

Thank you.

Chdid

[hek]

What version/type of gateway are you running?

Seems like the type sent isn't interpreted correctly. Are you running beta on the gw?
Quick-fix .. Send "1" or "0".

[chdid]

I'am running a gateway on an ESP8266.

I take the last version of the ESP8266 gateway. It's OK.

Thank you
Chdid