Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

MySensors 1.5.1?

gandy.bruno last edited by

Hello

I want to know if it is expected an update of the library version 1.5.1

Best regards
Reply Quote 0
1 Reply Last reply
mfalkvidd Mod last edited by

(forked new topic from step-by-step-procedure-to-connect-the-nrf24l01-to-the-gpio-pins-and-use-the-raspberry-as-a-serial-gateway)
Reply Quote 0
1 Reply Last reply
tbowmo Admin last edited by

@gandy-bruno

I think that the next release will be 2.0.0.. (Or that is what we are aiming for at the moment)
Reply Quote 0
1 Reply Last reply

3
Posts

888
Views

Log in to reply

Suggested Topics

Pjon Script
General Discussion • • sindrome73

6

0
Votes

6
Posts

38
Views

@nagelc I'm thinking about making some kind of shelves with PJON built in. The shelves will have a wireless charger and with PJON I can communicate "Wireless". So on that shelf I can put some things like small candles, maybe a modified humidifier. Things like that xd
set hostname using static IP
General Discussion • mysensors hostname static • • sandorhoffmann

3

0
Votes

3
Posts

18
Views

I did a grep on the source code and found this snipper #if defined(MY_GATEWAY_ESP8266) || defined(MY_GATEWAY_ESP32) // Turn off access point WiFi.mode(WIFI_STA); #if defined(MY_GATEWAY_ESP8266) WiFi.hostname(MY_HOSTNAME); #elif defined(MY_GATEWAY_ESP32) WiFi.setHostname(MY_HOSTNAME); #endif #if defined(MY_IP_ADDRESS) WiFi.config(_MQTT_clientIp, _gatewayIp, _subnetIp); #endif /* End of MY_IP_ADDRESS */ (void)WiFi.begin(MY_WIFI_SSID, MY_WIFI_PASSWORD, 0, MY_WIFI_BSSID); #endif MySensors uses the standard ESP libraries for this. So I expect it to work. But you need to provide at least a bit of source code. Right now it's hard to answer your question. Regarding to MySensors: A HTTP hostname can only be set for Gateways that either use Wifi or Ethernet For nodes you can provide a sketchname and that will be seen in your controller. Regarding to static non static IP addresses. I prefer to use DHCP and set that device in my router as a static IP. There I also give it another hostname. So that in case I have to replace my Gateway I can do it all in the router. Hope this helps. But please provide more info on what you're trying to achieve
CHATGPT My new best friend!
General Discussion • • Tmaster

5

3
Votes

5
Posts

22
Views

@Tmaster I think it writes better code than a lot of code I've seen, and the documentation is a lot better. The latter, of course, is because most coders don't document. some key elements: good statement of work -- Purpose of the Code is key (did you write that? Good job!). This will guide the AI to write what you want. descriptive variables good documentation code is independent of reading sensors up-to-down/down-to-up I spent a couple hours analyzing, researching and writing and re-writing this and all I can say is that the AI didn't catch is, as far as I can see, if your sensors are too far apart or your magnet is too weak, you could get false readings. You, being the author of AI directive, are responsible for for the code. The AI is just a tool. I started my coding with assembly language, though at that time we still had to enter the binary on some machines (set 16 switches, then press commit). ForTran and COBOL were the first real high level languages and subsequent languages, pascal, c, java, etc. were improvements. AI is a quantum step. It's still coding, but you have to learn how to talk to the AI to get what you want. Good project! Let us know how it turns out and if you had to tweak the code. -OSD
Code Garage to the rescue.
General Discussion • • skywatch

18

1
Votes

18
Posts

215
Views

it is up and running
AI: What is the future of Wikis and Forums?
General Discussion • • Eme

5

1
Votes

5
Posts

34
Views

@Homer I take care to say Good morning Sir, and Thank you Sir... You never know when it comes back to bite my tail.
Keen to build again
General Discussion • • Homer

9

0
Votes

9
Posts

54
Views

MySensors is an EXCELLENT project. It allows for complete control over the various sensors. It's extremely simple. Its drawback is that it's open source, so it's unfunded and development is slow, but I don't think there are any better projects than this at the moment.

50
Online

11.7k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1