Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

MySensors 1.5.1?

gandy.bruno last edited by

Hello

I want to know if it is expected an update of the library version 1.5.1

Best regards
Reply Quote 0
1 Reply Last reply
mfalkvidd Mod last edited by

(forked new topic from step-by-step-procedure-to-connect-the-nrf24l01-to-the-gpio-pins-and-use-the-raspberry-as-a-serial-gateway)
Reply Quote 0
1 Reply Last reply
tbowmo Admin last edited by

@gandy-bruno

I think that the next release will be 2.0.0.. (Or that is what we are aiming for at the moment)
Reply Quote 0
1 Reply Last reply

3
Posts

888
Views

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

4

0
Votes

4
Posts

2572
Views

@andriej Hi, I had problem using the main branch mysensors/Raspberry, that because of the bit-field struct (header_s) in Sensor.h They will get packed in different order on the arduino compared to the RPi (at least with my compiler, gcc). In order to fix this I created the 1.4dev branch. It uses full bytes instead of the bit-fields, but you need (of cause) to compile both the sensors (arduino) and the gateway (RPi) using the 1.4dev branch. We need to fix this in the main branch later on (and use the same files as in mysensors/Arduino/libraries/MySensors)
GatawayESP8266 - Compile error
General Discussion • gatawayesp8266 compile error • • skom

15

0
Votes

15
Posts

123
Views

@eiten Ran into the same error but of course the community is always at hand, ready to help! Great! I'm using MySensors 2.3.2 release version. Downgrading the ESP8266 board library to 2.7.4 as suggested by @OldSurferDude did the trick. I'm still clinging to MySensors. So simple and inexpensive to use! All sensors and other stuff connects over three MQTT GW in three locations back to my Home Assistant. PS: Get well soon! Regards, Gunnar
What is form factor?
General Discussion • • Luosi

1

0
Votes

1
Posts

16
Views

No one has replied
Running out of nodeId's
General Discussion • mysensors • • NielBierman

10

3
Votes

10
Posts

63
Views

@GLAB You can set the frequencies using the settings in MyConfig.h, which is in the MySensors folder. If you put any of the defines from MyConfig.h into your sketch, they will override the MyConfig.h setting for that sketch only. If you are using the RF24 radio, there are different channels which correspond to a given frequency. The default is channel 76. There is a list of typical channels in MyConfig.h. If you want to change the channel for all the sketches, change it in MyConfig.h. If you want to change it just for the sketch, add a define to the sketch. For example: #define MY_RF24_CHANNEL (84) The problem with changing the channel in a sketch is that the gateway has to be on the same channel to receive from the node. So, normally it makes sense to change in MyConfig.h because you usually want the gateway and all the nodes on the same channel. Other radio's like the RFM69 list the frequency instead of using a channel. They can be overridden in the sketch as well. You can find the defines that are needed in MyConfig.h
Old hardware migration
General Discussion • • dbemowsk

3

0
Votes

3
Posts

39
Views

@OldSurferDude My old 2.0 setup is with nRF24L01 radios. This is a link to the thread on some light switches that I designed and built. https://forum.mysensors.org/topic/7376/us-decora-wall-switch-continued/2 I am aware that you cannot have two MQTT gatways. When I designed my old setup I was not that familiar with MQTT so I never ended up implementing it. On the home assistant server that I have set up though, I have installed the MQTT broker on there so I should be able to comunicate with any MySensors stuff over MQTT in the future devices I make/set up. As I mentioned, I do have a Home Assistant box that I have started about 4 months ago and eventually want to migrate my Vera equipment to the HA box. As for the YAML and Python, I'll muddle my way through. used to program in PHP and have done enough on Arduino that I'm sure it won't hurt my brain too much.
Need advice on solar powering with LiFePo4 battery
General Discussion • • willemx

17

0
Votes

17
Posts

168
Views

LiFePO4 batteries are a great choice because they have a long life cycle and are much safer than other lithium-based batteries. However, you need a solar charge controller that’s compatible with LiFePO4 to prevent overcharging and maintain efficiency. A good MPPT controller can significantly boost energy harvest from your panels. Also, ensure your solar panel output matches your power needs. If you're in solar ireland, you might find some local companies that offer tailored solutions for maximizing solar efficiency in lower light conditions.

MySensors 1.5.1?

Suggested Topics

Update RF24 library to latest version
Bug Reports • • andriej

GatawayESP8266 - Compile error
General Discussion • gatawayesp8266 compile error • • skom

What is form factor?
General Discussion • • Luosi

Running out of nodeId's
General Discussion • mysensors • • NielBierman

Old hardware migration
General Discussion • • dbemowsk

Need advice on solar powering with LiFePo4 battery
General Discussion • • willemx

51
Online

11.5k
Users

11.1k
Topics

112.7k
Posts

MySensors 1.5.1?

Suggested Topics

Update RF24 library to latest version Bug Reports • • andriej

GatawayESP8266 - Compile error General Discussion • gatawayesp8266 compile error • • skom

What is form factor? General Discussion • • Luosi

Running out of nodeId's General Discussion • mysensors • • NielBierman

Old hardware migration General Discussion • • dbemowsk

Need advice on solar powering with LiFePo4 battery General Discussion • • willemx

51Online

11.5kUsers

11.1kTopics

112.7kPosts

Update RF24 library to latest version
Bug Reports • • andriej

GatawayESP8266 - Compile error
General Discussion • gatawayesp8266 compile error • • skom

What is form factor?
General Discussion • • Luosi

Running out of nodeId's
General Discussion • mysensors • • NielBierman

Old hardware migration
General Discussion • • dbemowsk

Need advice on solar powering with LiFePo4 battery
General Discussion • • willemx

51
Online

11.5k
Users

11.1k
Topics

112.7k
Posts