How To - Doorbell Automation Hack

[petewill]

@Newzwaver Hmm. I doubt this would work for you to fully control it but you may still be able to trigger it. How do you control it now? Through an app or something?

[Moshe Livne]

Hello all - sorry I have been away for so long...
This bring back memories http://forum.mysensors.org/topic/1620/mysensored-doorbell
I wish I found a way of triggering the notification from the ring and not the other way around, as this way when something happen to your arduino the doorbell will not ring. Didn't happen yet - it works perfectly for 6 months but I would feel more relaxed if it was the other way around. Oh well...

[petewill]

@Moshe-Livne Cool! You can look at it the other way around on the Arduino processing the ring issue you raised. I now have the ability to turn off the ring if I want to. So I guess there is some give and take :)

[Moshe Livne]

@petewill ummmm you could still cut the ring even if it was the other way around with a relay. Sorry to be a pain :-) can't fight my mold hehehe. generally I find the reliability of dorrbells (especially the old wired kind) to be excellent. mine has been working flawlessly for at least 35 years.

[petewill]

@Moshe-Livne Ok, I must have misunderstood. I thought you wanted the bell to ring no matter what then just detect the signal so you could send it to your gateway. Either way, that's why MySensors is so great, you can do pretty much what ever YOU want, not what someone else wants :)

[Moshe Livne]

@petewill My original plan was to unintrusively detect the ring and trigger the arduino without effecting the bell circuit. However, it proved to be a bit more complicated and 2 dead arduinos and several other fried components later I gave up.

[mike0913]

I am new to home automation but curious if this same setup would work by having the arduino centrally located with the transformer in a closet and use the extra connections on the existing 4 conductor wire from the transformer to connect the new relay installed in the chime?

All this saves is some extra space and having to run 5V to the chime but one could use a larger arduino for additional automation projects rather than dedicated to just the chime.

Very nice tutorial- very easy to follow. Thanks

[drock1985]

Hey @mike0913 ,

You can check out what I did with my Doorbell hack here (http://forum.mysensors.org/topic/2293/how-to-2-door-chime-automation-hack-thanks-petewill), it may help with your situation. Basically, I used the 16VAC input from the doorbell to power my Arduino, relays, and actual doorbell chime itself. Due to confined space, I had to mount mine in an external box below the existing door chime.

[Newzwaver]

@petewill, thanks for the reply and sorry it took me so long. I have decided to keep it to a small project starting with the remote on off, then moving to a trigger to my camera. I plan on breaking the doorbell down once the wife is out of the house for a day, lol. Thanks again.

[riochicken]

@petewill

Thanks for the code! For some reason it is not functioning on my arduino pro, the relay doesnt do anything when I push the button on pin 3, I do see within the Vera that the button is being pushed I have no clue what is going wrong..

This is the output from the serial monitor:
send: 16-16-0-0 s=255,c=3,t=15,pt=2,l=2,sg=0,st=ok:0
send: 16-16-0-0 s=255,c=0,t=17,pt=0,l=5,sg=0,st=ok:1.5.3
send: 16-16-0-0 s=255,c=3,t=6,pt=1,l=1,sg=0,st=ok:0
sensor started, id=16, parent=0, distance=1
send: 16-16-0-0 s=255,c=3,t=11,pt=0,l=16,sg=0,st=ok:Doorbell Monitor
send: 16-16-0-0 s=255,c=3,t=12,pt=0,l=3,sg=0,st=ok:1.0
send: 16-16-0-0 s=1,c=0,t=3,pt=0,l=0,sg=0,st=ok:
send: 16-16-0-0 s=0,c=0,t=1,pt=0,l=0,sg=0,st=ok:
Pushing button
send: 16-16-0-0 s=0,c=1,t=16,pt=1,l=1,sg=0,st=ok:1
send: 16-16-0-0 s=0,c=1,t=16,pt=1,l=1,sg=0,st=ok:0
Pushing button
send: 16-16-0-0 s=0,c=1,t=16,pt=1,l=1,sg=0,st=ok:1
send: 16-16-0-0 s=0,c=1,t=16,pt=1,l=1,sg=0,st=ok:0

Anybody that can help me out?

Thanks!

Kind regards,

Richard

[riochicken]

@riochicken

Never mind, I didnt know I had to enable both switches within the arduino interface... ahum..

Thanks anyhoe!

Kind regards

Richard

[riochicken]

Excellent hack, works like a charm! I added two extra activations for my doorbell so it rings two times short and one longer time... Is there a way to create a variable in the Vera options so you can change the number of time the relay activates? Now I added them in the code but that is not really handy when the thing is build in and such... :)

Thanks!

[petewill]

@riochicken said:

Is there a way to create a variable in the Vera options so you can change the number of time the relay activates?

Yeah, that should be possible. Have a look at the Irrigation Controller code. That has some examples of getting variables from the controller.

[timropp]

I had my doorbell working fine on Vera for months, but now I'm switching over to Domoticz. I used the updated domoticz version of the code above (by drock1985) but it's still not working right. My only changes were the pin assignments to match my wiring and setting the repeater to true since it's powered.

My domoticz is version v3.4834. Mysensors ethernet gateway is working fine. When I powered up the doorbell, I got an unknown node with sketch "unknown" show up under mysensors. It has 2 children - a repeater with childID 255, and an unknown with childID 0 and a V_Tripped value.

Any idea what I need to do to make it work?

[drock1985]

@timropp

Try this code and see if it works.

/*
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 2.1 - Derrick Rockwell (Drock1985) 
 * - Complete Re-write of code to provide better flow/structure. 
 * Version 2.0 - ResentedPoet
 * 
 * Based on original concept/code by @petewill for 1 Door bell chime. See original thread
 * http://forum.mysensors.org/topic/2064/how-to-doorbell-automation-hack
 * This sketch is used to control a front and back doorbell ring with relays as well as send an
 * alert when the buttons are pressed. For front door, Connect the button to ground and digital
 * pin 3.  The relay controlling the doorbell is conntected to pin 4. For rear door bell
 * connect second button to ground and digital pin 5. The relay controlling that pin goes 
 * to pin 6.
 */
#include <MySensor.h>
#include <SPI.h>
#include <Bounce2.h>

#define NODE_ID 2                   // or set to AUTO if you want gw to assign a NODE_ID for you.
#define FRONT_DOOR_BUTTON  3        // Arduino Digital I/O pin number for the front doorbell button 
#define FRONT_CHIME_RELAY  4        // Aduino Digital I/O pin number for the front door chime relay
#define CHILD_ID_0 0                // Child ID for the front doorbell sensor
#define BACK_DOOR_BUTTON 5          // Arduino Digital I/O pin number for the back doorbell button
#define BACK_CHIME_RELAY 6          // Aduino Digital I/O pin number for the back door chime relay
#define CHILD_ID_1 1                // Child ID for the back doorbell sensor
#define CHILD_ID_2 2                // Child ID for the mute option
#define CHIME_MUTE_STATE            // Used to hold value of door chime mute funtion. 
#define CHIME_OFF 0                 // Variable to define ring the chime
#define CHIME_ON 1
#define FRONT_CHIME_RELAY_ON LOW    // Variable for front chime. Reverse low/high if relay pin set different
#define FRONT_CHIME_RELAY_OFF HIGH  // Variable for front chime. Reverse low/high if relay pin set different
#define BACK_CHIME_RELAY_ON LOW     // Variable for front chime. Reverse low/high if relay pin set different
#define BACK_CHIME_RELAY_OFF HIGH   // Variable for front chime. Reverse low/high if relay pin set different

Bounce debouncerF = Bounce();
Bounce debouncerB = Bounce();

boolean CHIME_MUTE = 1;

MySensor gw;
MyMessage msg(CHILD_ID_2, CHIME_MUTE);

MyMessage frontDoorbell(CHILD_ID_0, V_TRIPPED);
MyMessage backDoorbell(CHILD_ID_1, V_TRIPPED);
MyMessage chimeMute(CHILD_ID_2, V_STATUS);
int pestTimeout = 4000;               // Delay between registered button presses. Stops button mashers ;) Set to whatever delay you want.
unsigned long previousMillis=0;       // Tracks time since last door chime button press

void setup() {

  gw.begin(incomingMessage, NODE_ID);

  // Send the sketch version information to the gateway and Controller
  gw.sendSketchInfo("2 Door bell/chime Monitor", "2.1");

  // Setup the button and activate internal pull-up
  pinMode(FRONT_DOOR_BUTTON, INPUT);
  pinMode(BACK_DOOR_BUTTON, INPUT);
  digitalWrite(FRONT_DOOR_BUTTON, HIGH);
  digitalWrite(BACK_DOOR_BUTTON, HIGH);
  
  // After setting up the button, setup debouncer
  debouncerF.attach(FRONT_DOOR_BUTTON);
  debouncerB.attach(BACK_DOOR_BUTTON);
  debouncerF.interval(5);
  debouncerB.interval(5);

  // Register all sensors to gw (they will be created as child devices)
  gw.present(CHILD_ID_0, S_MOTION);
  gw.present(CHILD_ID_1, S_MOTION);
  gw.present(CHILD_ID_2, S_LIGHT);
  gw.send(msg.set(CHILD_ID_2, CHIME_MUTE));
  

  // Make sure relays are off when starting up
  digitalWrite(FRONT_CHIME_RELAY, FRONT_CHIME_RELAY_OFF);
  digitalWrite(BACK_CHIME_RELAY, BACK_CHIME_RELAY_OFF);
  // Then set relay pins in output mode
  pinMode(FRONT_CHIME_RELAY, OUTPUT);
  pinMode(BACK_CHIME_RELAY, OUTPUT);

}

void loop() {
  gw.process();
  unsigned long currentMillis = millis();
  debouncerF.update();
  debouncerB.update();
  int valueF = debouncerF.read();
  int valueB = debouncerB.read();
//Front Doorbell

if ( ((unsigned long)(currentMillis - previousMillis) >= pestTimeout) && valueF != HIGH && CHIME_MUTE == 1) {
  digitalWrite(FRONT_CHIME_RELAY, FRONT_CHIME_RELAY_ON);
  gw.send(frontDoorbell.set(1));
  gw.wait(50);
  digitalWrite(FRONT_CHIME_RELAY, FRONT_CHIME_RELAY_OFF);
  gw.send(frontDoorbell.set(0));
  previousMillis = currentMillis;
}

if ( ((unsigned long)(currentMillis - previousMillis) >= pestTimeout) && valueF != HIGH && CHIME_MUTE == 0) {
  gw.send(frontDoorbell.set(1));
  gw.wait(50);;
  gw.send(frontDoorbell.set(0));
  previousMillis = currentMillis;
}
//Back Doorbell

if ( ((unsigned long)(currentMillis - previousMillis) >= pestTimeout) && valueB != HIGH && CHIME_MUTE == 1) {
  digitalWrite(BACK_CHIME_RELAY, BACK_CHIME_RELAY_ON);
  gw.send(backDoorbell.set(1));
  gw.wait(450);
  digitalWrite(BACK_CHIME_RELAY, BACK_CHIME_RELAY_OFF);
  gw.send(backDoorbell.set(0));
  previousMillis = currentMillis;
}

if ( ((unsigned long)(currentMillis - previousMillis) >= pestTimeout) && valueB != HIGH && CHIME_MUTE == 0) {
  gw.send(backDoorbell.set(1));
  gw.wait(50);
  gw.send(backDoorbell.set(0));
  previousMillis = currentMillis;
}
}
void incomingMessage(const MyMessage &message) {
  // We only expect one type of message from controller. But we better check anyway.
  if (message.isAck()) {
     Serial.println("This is an ack from gateway");
  }

  if (message.type == V_STATUS) {
     // Change relay state
     CHIME_MUTE = message.getBool();
     gw.send(msg.set(CHILD_ID_2, CHIME_MUTE?CHIME_ON:CHIME_OFF));
     // Store state in eeprom
     gw.saveState(CHILD_ID_2, CHIME_MUTE);
    
     // Write some debug info
     Serial.print("Incoming change for sensor:");
     Serial.print(message.sensor);
     Serial.print(", New status: ");
     Serial.println(message.getBool());
   } 
}

[timropp]

Thanks, I'll give that a try. I don't have any need for the dual bell functionality, but we can see if it works and if so, then comment out the back bell part to simplify things.

[timropp]

Tried that sketch (with just changing pin assignments and flipping the relay high/low settings). As soon as I powered it up, the relay started clicking every 4 seconds and it never appeared in Domoticz. I think it's because after the pin is set to input, there's " digitalWrite(FRONT_DOOR_BUTTON, HIGH);" command that's like someone holding the button down.

Went back to the original sketch I used. I changed from an auto NODE_ID to a fixed setting in the defines and re-uploaded it. The device appeared in Domoticz correctly! I've got a "doorbell sketch 1.0" with 3 devices - repeater, the doorbell button as a S_Motion, and the doorbell on/off as a S_Lights.

However, it still doesn't work. My wiring is shown above and it worked great under Vera. Now, I cannot get the doorbell to actually chime. Nor does the outdoor button do anything. I've verified the wiring, but shorting the A0 pin to the ground input doesn't do anything like it should. However, there's ANOTHER ground next to the A0 (under the wireless card), and if I short the A0 to that ground pin, the switch shows on in Domoticz. I can change the wiring since for some reason which ground I use is making a difference.

No matter what, still no relay action though. I tried turning the doorbell on/off switch both ways and it made no difference. In either setting, shorting the two pins turns the switch in Domoticz on.

I was comparing the two sketches (the one I'm using, and the dual-bell one). The single bell sketch sets the button pin with pinmode(Doorbell_pin, input_pullup) where the dual uses input without the pullup. Which should be right?

[drock1985]

@timropp

The sketch I use doesn't use internal pull ups; external only.

As for the relay clicking, could be either the jumper on the relay, or not enough current to power it properly.

Not sure why you are having issues with either of the scripts. What type of gateway do you use?

[timropp]

It's an ethernet gateway.

I don't think it's really a Mysensors issue though as I think about it - the doorbell should ring when you press the button whether you have the gateway running or not. And I'm not even getting that. In fact, I AM getting the signal to the gateway, but it's not activating the relay.

Is it possible that the doorbell on/off switch isn't working right in the code? I never used that before. I think I'll try tomorrow (kids in bed now, so can't really play around with a doorbell!) removing that switch for now and have it always set to on.

I looked through comparing the sketch I'm using now (the one drock1985 made that's for domoticz) and the original. The only change is moving the gw.send command and changing it slightly. But again, that shouldn't impact the bell physically working. So there's something else going on.

Is there a way to check if the code uploaded to the arduino correctly? I'm using the rboard and a FTDI to upload. I'm wondering if something isn't going weird there and it's not uploading correctly and that's why I'm getting different issues every time I try something...

[drock1985]

Not really. You could try uploading at a slower speed. Slower speed over serial usually equals less chance of missed data.

Have you tried running this connected to your PC and viewing the data from serial console/window? Copy/paste the output from the serial monitor so we can see what's going on.