DIY Outdoor LED

korttoma

@rvendrame yeah, that is how I would recommend to do also. An additional regulators are worth it, just to be safe.

activemind

Bringing back and old thread from the dead as I have some time now to spend on this.

Did some more research on Amazon and ended up ordering these LED lights

http://www.amazon.com/Lemonbest®-Outdoor-Decorative-Lighting-Landscape/dp/B012VLSYJE?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_detailpage_o00_s00

Planning on using MYS board to control these.

http://forum.mysensors.org/topic/207/my-sensorboard-mys-1-0beta

I have 2 questions:

These are 12V and MyS board can take 12V input too. So I can power them off using the same 12V wire. Shall I use a relay to control these lights ? Couldnt find the current draw but I plan on measuring it once I get them in.
Should I try to embed the myS board in the light case or look into an external waterproof plastic box? These are going to be outdoors.

-AM

mfalkvidd

@activemind said:

These are 12V and MyS board can take 12V input too. So I can power them off using the same 12V wire. Shall I use a relay to control these lights ? Couldnt find the current draw but I plan on measuring it once I get them in.

They are rated for 5W. 12V/5W=2,4A

Edit: NO, 5W/12V=0.42A. My bad.

mfalkvidd

@activemind said:

Should I try to embed the myS board in the light case or look into an external waterproof plastic box? These are going to be outdoors.

The case seems to be made if aluminum. That will probably block radio signals. So if you're planning to use radio, go for a plastic box.

activemind

Thanks for the feeback. You make good points. I will plan for an external waterproof box for all mysensors circuitry.

Does using a FET sound good or shall I use a relay?

Something like this should be pretty inexpensive..

http://www.ebay.com/itm/Mos-fet-40v-190amp-for-3k-5k-6k-main-baord-of-12v-power-inverter-/322048034708?hash=item4afb8f0794:g:piQAAOSwHgVW8Ps0&vxp=mtr

-AM

activemind

Or something like this would be better:

http://www.ebay.com/itm/12V-High-Level-1-Channel-Relay-Module-Trigger-Expansion-Board-for-Arduino-Relays-/361353342158?hash=item5422566cce:g:fzQAAOSwjVVVn09H

-AM

mfalkvidd

There is no information on which mosfet in the ebay listing. I would one that has a name/number so the data sheet can be looked up. The MySensors store recommends IRLZ44N.

Downside with mosfet: can become hot, might need a heat sink
Upside with mosfet: can be used to dim the lights

By the way, how are you planning to get the power to the units? 12V from your house into the garden? In that case you might get problems if your garden is large, transferring power over long distances with low voltage is hard.

activemind

Will the FET get hot even with 2.4A when its rated for much more?

I am thinking of building one node and trying it out to see if there is any fallout. This will be for my landscape lights so its not like it will be running 24/7.

The plan IS to run a 14/2 wire running 12V. I could do 12/2 if the voltage drop is too bad. My runs should not be obscenely long...I guess I will have to just try and see what the drop is.

Thanks again for all your feedback.

-AM

mfalkvidd

@activemind said:

Will the FET get hot even with 2.4A when its rated for much more?

Probably not. As long as you check the rating you should be fine.

The plan IS to run a 14/2 wire running 12V. I could do 12/2 if the voltage drop is too bad. My runs should not be obscenely long...I guess I will have to just try and see what the drop is.

14 AWG has a resistance of 0.00829 ohm per meter (source). Assuming you have 15m from the outlet to the light, the resistance in the cable will be 0.2487 ohm (0.00829 * 15 * 2). At 2.4A that will result in a voltage drop of 2.4 * 0.2487=0,60V. That shouldn't be a problem.

If the distance from the outlet to the lights is longer, and you want to connect multiple lights without running multiple cables, the calculation doesn't look very good. Let's say the cable needs to be 30m and you want 5 lights, then we have a cable resistance of 0.00829 * 30 * 2=0.5 ohm and a voltage drop of 2.4 * 5 * 0.5=6V :exclamation:
12 AWG will give you 0.00521 * 30 * 2=0.3126 ohm and 2.4 * 5 * 0.3126=3,75V voltage drop which also might be too much.

activemind

I would put my distance around 20m so that should be okay but I DO plan on putting multiple of these on a single run hence larger current!

I really dont want to do multiple runs.

Two options:

I need to see how bright the light is with < 12V ?
Use some regulator to bump up the voltage at the location. I will be building a seperate box anyways to house the FET and MySensors circuitry, so maybe put a regulator there?

What do you think?

-AM

mfalkvidd

Option 2 would require larger current (2.4A at 12V will require at least 4.8A at 6V) so the problem just gets worse. Better to increase the voltage, maybe run 24V and regulate down to 12V at each light?

activemind

@mfalkvidd
But i already have server grade 12v power supplies and i dont want to buy new ones.

Is the LED really going to draw 2.4A? I will hook up one today and measure.

What's the max safe amount of current i can carry on 14/2 LV wire?

If push comes to shove, i might do multiple runs 😢

-AM

Boots33

@activemind

Each led would draw around 410ma
5/12=.416

mfalkvidd

According to http://www.powerstream.com/Wire_Size.htm the limit for 14 awg is 5.9A.

mfalkvidd

@Boots33 correct! I edited my previous calculation. Sorry for misleading you @activemind My voltage drop calculations are off by 5x so you will be able to use 5 lights instead of 1 at 2.4A. That means you'll only get in trouble if you plan to use 20+ lights.

activemind

@mfalkvidd

Phew! I think i should be okay as i dont plan on putting more than 10 on a string.

-AM

activemind

Slightly off topic question, but I am looking for a benchtop power supply (yeah! been managing without one for so long) and wanted y'all opinion on this:

http://www.aliexpress.com/item/DPS-305BM-Digital-Control-30V-5A-DC-Laboratory-Adjustable-power-supply-for-Laptop-Repair/785631910.html?spm=2114.30010308.3.1.zVG69O&ws_ab_test=searchweb201556_9,searchweb201602_3_10037_10017_10034_10021_507_10022_10032_10009_10020_10008_10018_10019,searchweb201603_2&btsid=0ad919a2-0637-4aba-9918-1454e14c1f43

Or

http://www.aliexpress.com/item/Free-Shipping-Benchtop-Power-Board-DIY-a-desktop-DC-power-by-an-old-computer-power-supply/32615031628.html?spm=2114.13010208.99999999.261.IcezQA

Or something else that doesnt cost a fortune.(<$100).

-AM

activemind

Or this one looks interesting too...good reviews on Amazon

http://www.amazon.com/Tekpower-TP3005T-Variable-Linear-Supply/dp/B00ZBCLJSY/ref=sr_1_2?s=industrial&ie=UTF8&qid=1462210519&sr=1-2

activemind

Ended up blowing the regulator on a 5V pro mini when powered at 12V. Maybe its the "clone" part from china that is causing this but it gave out smoke and finally died when powered at 9V.

Going to assemble another 5V pro mini and power at 5V to test the board and circuit.

Thinking about putting a hefty 150R 1W ressistor before feeding 12V to RAW in final circuit.

Thoughts?

-AM

Boots33

@activemind

You could also use an external regulator module to supply the 5v. at the moment you are running right on the pro mini maximum voltage which in my mind is never a good thing for long term reliability. I have used these modules with great success, they work with a wide level of input voltage and can be adjusted, so can be set to 5v or 3v output . They are quite cheap as well so if you have the room they may be worth a look.

DIY Outdoor LED

8

11.7k

11.2k

113.0k