problem with implementation of my sensors in rollershutter sketch

ihtgtwtd

hello,
I found a nice rollershutter sketch in the german arduino forum (http://forum.arduino.cc/index.php?topic=247811.60). I tried to implement mysensors but i'm stuck somehow.
my arduino gets a node ID and the 3 rollershutters are registered, I can send commands and they show up in the serial monitor but I don't know how to route the commands to the relays.
If it matters, the controller is domoticz.

// Enable debug prints to serial monitor
#define MY_DEBUG 
// Enable and select radio type attached
#define MY_RADIO_NRF24
// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE

#include <MySensors.h>
#include <SPI.h>

// Rollladensteuerung by jurs for German Arduino-Forum
#define BUTTONPRESSED LOW
#define RELAYACTIVE LOW

MyMessage sensorMsg0(0,V_DIMMER);
MyMessage sensorMsg1(1,V_DIMMER);
MyMessage sensorMsg2(2,V_DIMMER);

enum {NOACTION, UPACTION, DOWNACTION};

struct roll_t{byte downPin; byte upPin; boolean downPressed; boolean upPressed; byte action; unsigned long actionStarttime; unsigned long actionTimeout; byte relayOnePin; byte relayTwoPin;};

roll_t rollladen[]={
  {2,3,false, false, NOACTION,0,60000L, A0, A1}, // Button-Pins 2, 3, Relay-Pins A0, A1, Timeout 60 secons
  {4,5,false, false, NOACTION,0,45000L, A2, A3}, // Button-Pins 4, 5, Relay-Pins A2, A3, Timeout 45 secons
  {6,7,false, false, NOACTION,0,45000L, A4, A5}, // Button-Pins 6, 7, Relay-Pins A4, A5, Timeout 45 secons
};

#define ANZAHLROLLLADEN sizeof(rollladen)/sizeof(rollladen[0])


void setup()
{
  Serial.begin(115200);
  for (int i=0;i<ANZAHLROLLLADEN;i++)
  {
    if (BUTTONPRESSED==HIGH)
    {
      pinMode(rollladen[i].downPin,INPUT);
      pinMode(rollladen[i].upPin,INPUT);
    }
    else
    {
      pinMode(rollladen[i].downPin,INPUT_PULLUP);
      pinMode(rollladen[i].upPin,INPUT_PULLUP);
    }
    if (RELAYACTIVE==LOW)
    {
       digitalWrite(rollladen[i].relayOnePin,HIGH);
       digitalWrite(rollladen[i].relayTwoPin,HIGH);
    }
    pinMode(rollladen[i].relayOnePin,OUTPUT);
    pinMode(rollladen[i].relayTwoPin,OUTPUT);
  }
}


void switchRelay(byte i)
{
  Serial.print("Schalte Rolladen-");
  Serial.print(i);
  switch (rollladen[i].action)
  {
    case NOACTION: // STOP
      digitalWrite(rollladen[i].relayOnePin,!RELAYACTIVE);
      digitalWrite(rollladen[i].relayTwoPin,!RELAYACTIVE);
      Serial.println(" STOP");
      break;
    case UPACTION: // UP
      digitalWrite(rollladen[i].relayOnePin,RELAYACTIVE);
      digitalWrite(rollladen[i].relayTwoPin,!RELAYACTIVE);
      Serial.println(" UP");
      break;
    case DOWNACTION: // DOWN
      digitalWrite(rollladen[i].relayOnePin,!RELAYACTIVE);
      digitalWrite(rollladen[i].relayTwoPin,RELAYACTIVE);
      Serial.println(" DOWN");
      break;
  }
}



void loop(void) 
{
  byte state;
  for (int i=0;i<ANZAHLROLLLADEN;i++)
  {
    // Prüfen, ob Down gedrückt wurde
    state=digitalRead(rollladen[i].downPin);
    if (BUTTONPRESSED==LOW) state=!state;
    if (state && !rollladen[i].downPressed)
    {
      switch (rollladen[i].action)
      {
        case NOACTION: rollladen[i].action=DOWNACTION;
                       rollladen[i].actionStarttime=millis();
                       switchRelay(i);
                       break;
        default: if (rollladen[i].action!=NOACTION)
                 {
                   rollladen[i].action=NOACTION;
                   switchRelay(i);
                 }
      }
    }
    rollladen[i].downPressed=state;
    
    // Prüfen, ob Up gedrückt wurde
    state=digitalRead(rollladen[i].upPin);
    if (BUTTONPRESSED==LOW) state=!state;
    if (state && !rollladen[i].upPressed)
    {
      switch (rollladen[i].action)
      {
        case NOACTION: rollladen[i].action=UPACTION;
                       rollladen[i].actionStarttime=millis();
                       switchRelay(i);
                       break;
        default: if (rollladen[i].action!=NOACTION)
                 {
                   rollladen[i].action=NOACTION;
                   switchRelay(i);
                 }
      }
    }
    rollladen[i].upPressed=state;
    
    // Prüfen auf Timeout
    if (rollladen[i].action!=NOACTION && millis()-rollladen[i].actionStarttime>=rollladen[i].actionTimeout)
    {
      rollladen[i].action=NOACTION;
      switchRelay(i);
    }
  }
  delay(5); // kleines Delay zum Entprellen der Buttons
}

void presentation()
{

  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Test", "1.0");

  // Fetch relay status
   for (int sensor = 1, pin = A0; sensor <= ANZAHLROLLLADEN; sensor++, pin++) {
  
    // Register all sensors to gw (they will be created as child devices)
      present(sensor, S_COVER);
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);
  } 
}


void receive(const MyMessage &message) {
  if (message.type == V_UP) {
    byte (message.sensor);
    Serial.println("going up:" + String(message.type));
  }
  else if (message.type == V_DOWN) {
    byte (message.sensor);
    Serial.println("going down:" + String(message.type));
  }
  else if (message.type == V_STOP) {
    byte (message.sensor);
    Serial.println("stopping:" + String(message.type));
  }
}

I don`t know how to fill out the last part of the sketch (void receive) so I just wrote something to make it compile.

I would really appreciate your help.

THX

AWI

@ihtgtwtd The sketch works with a statemachine. i.e the rollladen[i].action!=,<ACTION> determines the what each of the rollershutters i is doing.. What you should do is fill that action in receive() similar to what is done after a buttonpress for that action. i.e. assign the action for the respective shutter and set the timeout.

You can read look at the MySensors examples for rollershutter to find out how to get the values in the receive() routine.

ihtgtwtd

@AWI
thank you, that helped a lot.
I received my first arduino 3 weeks ago and since then I'm constantly learning. Getting things explained helps a lot.

the code receives my commands now but when I press down, all the down relays switch on/off and the other way around. I thought the line for (int i=0;i<ANZAHLROLLLADEN;i++) declares the number of the rollershutter.

// Enable debug prints to serial monitor
#define MY_DEBUG 
// Enable and select radio type attached
#define MY_RADIO_NRF24
// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE

#include <MySensors.h>
#include <SPI.h>

// Rollladensteuerung by jurs for German Arduino-Forum
#define BUTTONPRESSED LOW
#define RELAYACTIVE LOW

MyMessage sensorMsg0(0,V_DIMMER);
MyMessage sensorMsg1(1,V_DIMMER);
MyMessage sensorMsg2(2,V_DIMMER);

enum {NOACTION, UPACTION, DOWNACTION};

struct roll_t{byte downPin; byte upPin; boolean downPressed; boolean upPressed; byte action; unsigned long actionStarttime; unsigned long actionTimeout; byte relayOnePin; byte relayTwoPin;};

roll_t rollladen[]={
  {2,3,false, false, NOACTION,0,60000L, A0, A1}, // Button-Pins 2, 3, Relay-Pins A0, A1, Timeout 60 secons
  {4,5,false, false, NOACTION,0,45000L, A2, A3}, // Button-Pins 4, 5, Relay-Pins A2, A3, Timeout 45 secons
  {6,7,false, false, NOACTION,0,45000L, A4, A5}, // Button-Pins 6, 7, Relay-Pins A4, A5, Timeout 45 secons
};

#define ANZAHLROLLLADEN sizeof(rollladen)/sizeof(rollladen[0])


void setup()
{
  Serial.begin(115200);
  for (int i=0;i<ANZAHLROLLLADEN;i++)
  {
    if (BUTTONPRESSED==HIGH)
    {
      pinMode(rollladen[i].downPin,INPUT);
      pinMode(rollladen[i].upPin,INPUT);
    }
    else
    {
      pinMode(rollladen[i].downPin,INPUT_PULLUP);
      pinMode(rollladen[i].upPin,INPUT_PULLUP);
    }
    if (RELAYACTIVE==LOW)
    {
       digitalWrite(rollladen[i].relayOnePin,HIGH);
       digitalWrite(rollladen[i].relayTwoPin,HIGH);
    }
    pinMode(rollladen[i].relayOnePin,OUTPUT);
    pinMode(rollladen[i].relayTwoPin,OUTPUT);
  }
}


void switchRelay(byte i)
{
  Serial.print("Schalte Rolladen-");
  Serial.print(i);
  switch (rollladen[i].action)
  {
    case NOACTION: // STOP
      digitalWrite(rollladen[i].relayOnePin,!RELAYACTIVE);
      digitalWrite(rollladen[i].relayTwoPin,!RELAYACTIVE);
      Serial.println(" STOP");
      break;
    case UPACTION: // UP
      digitalWrite(rollladen[i].relayOnePin,RELAYACTIVE);
      digitalWrite(rollladen[i].relayTwoPin,!RELAYACTIVE);
      Serial.println(" UP");
      break;
    case DOWNACTION: // DOWN
      digitalWrite(rollladen[i].relayOnePin,!RELAYACTIVE);
      digitalWrite(rollladen[i].relayTwoPin,RELAYACTIVE);
      Serial.println(" DOWN");
      break;
  }
}



void loop(void) 
{
  byte state;
  for (int i=0;i<ANZAHLROLLLADEN;i++)
  {
    // Prüfen, ob Down gedrückt wurde
    state=digitalRead(rollladen[i].downPin);
    if (BUTTONPRESSED==LOW) state=!state;
    if (state && !rollladen[i].downPressed)
    {
      switch (rollladen[i].action)
      {
        case NOACTION: rollladen[i].action=DOWNACTION;
                       rollladen[i].actionStarttime=millis();
                       switchRelay(i);
                       break;
        default: if (rollladen[i].action!=NOACTION)
                 {
                   rollladen[i].action=NOACTION;
                   switchRelay(i);
                 }
      }
    }
    rollladen[i].downPressed=state;
    
    // Prüfen, ob Up gedrückt wurde
    state=digitalRead(rollladen[i].upPin);
    if (BUTTONPRESSED==LOW) state=!state;
    if (state && !rollladen[i].upPressed)
    {
      switch (rollladen[i].action)
      {
        case NOACTION: rollladen[i].action=UPACTION;
                       rollladen[i].actionStarttime=millis();
                       switchRelay(i);
                       break;
        default: if (rollladen[i].action!=NOACTION)
                 {
                   rollladen[i].action=NOACTION;
                   switchRelay(i);
                 }
      }
    }
    rollladen[i].upPressed=state;
    
    // Prüfen auf Timeout
    if (rollladen[i].action!=NOACTION && millis()-rollladen[i].actionStarttime>=rollladen[i].actionTimeout)
    {
      rollladen[i].action=NOACTION;
      switchRelay(i);
    }
  }
  delay(5); // kleines Delay zum Entprellen der Buttons
}

void presentation()
{

  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Test", "1.0");

  // Fetch relay status
   for (int sensor = 1, pin = A0; sensor <= ANZAHLROLLLADEN; sensor++, pin++) {
  
    // Register all sensors to gw (they will be created as child devices)
      present(sensor, S_COVER);
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);
  } 
}


void receive(const MyMessage &message) {
  byte state;
  for (int i=0;i<ANZAHLROLLLADEN;i++)
 
  if (message.type == V_UP) {
  {
      switch (rollladen[i].action)
      {
        case NOACTION: rollladen[i].action=UPACTION;
                       rollladen[i].actionStarttime=millis();
                       switchRelay(i);
                       break;
        default: if (rollladen[i].action!=NOACTION)
                 {
                   rollladen[i].action=NOACTION;
                   switchRelay(i);
                 }
      }
    }
    rollladen[i].upPressed=state;
    
    Serial.println("going up:" + String(message.type));
  }
  else if (message.type == V_DOWN) {
{
      switch (rollladen[i].action)
      {
        case NOACTION: rollladen[i].action=DOWNACTION;
                       rollladen[i].actionStarttime=millis();
                       switchRelay(i);
                       break;
        default: if (rollladen[i].action!=NOACTION)
                 {
                   rollladen[i].action=NOACTION;
                   switchRelay(i);
                 }
      }
    }
    rollladen[i].downPressed=state;
    
    Serial.println("going down:" + String(message.type));
  }
  else if (message.type == V_STOP) {
    {
      switch (rollladen[i].action)
      {
        case DOWNACTION: rollladen[i].action=NOACTION;
                       rollladen[i].actionStarttime=millis();
                       switchRelay(i);
                       break;

        case UPACTION: rollladen[i].action=NOACTION;
                       rollladen[i].actionStarttime=millis();
                       switchRelay(i);
                       break;
      }
    }
    Serial.println("stopping:" + String(message.type));
  }
}

Do you have any idea whats wrong?
thx

AWI

@ihtgtwtd in your receive() routine you are explicitly executing the action for all shutters in the for(.....) loop. What you should do is execute the action only for the shutter with the Id received . I.e. i = message.sensor

ihtgtwtd

@AWI
I don't get it. I inserted for (int i=0;i<message.sensor;i++) and the result is
switch 1 up= relay 1; switch 1 down= relay 2
switch 2 up= relay 1+3 ; switch 2 down=relay 2+4
switch 3 up= relay 1+3+5; switch 3 down=relay 2+4+6

shouldn't i++ give each following message.sensor it's own number?

maybe I am just too tired to get it.

thanks for your help, I'm going to sleep now

AWI

@ihtgtwtd something for when you wake up...

Remove the whole for loop. When you want to switch only 1 shutter only 1 should be activated. So replace the whole for loop with only i = message.sensor.

Btw.. I think the behavior of you last action is creative at least :bowtie:

ihtgtwtd

@AWI
the result was indeed interesting and fun to watch.

void receive(const MyMessage &message) {
  byte state;
  i = message.sensors
  
  if (message.type == V_UP) {
  {
      switch (rollladen[i].action)
      {
        case NOACTION: rollladen[i].action=UPACTION;
                       rollladen[i].actionStarttime=millis();
                       switchRelay(i);
                       break;
        default: if (rollladen[i].action!=NOACTION)
                 {
                   rollladen[i].action=NOACTION;
                   switchRelay(i);
                 }
    
     }
    }
    rollladen[i].upPressed=state;
    
    Serial.println("going up:" + String(message.type));
  }
  else if (message.type == V_DOWN) {
{
      switch (rollladen[i].action)
      {
        case NOACTION: rollladen[i].action=DOWNACTION;
                       rollladen[i].actionStarttime=millis();
                       switchRelay(i);
                       break;
        default: if (rollladen[i].action!=NOACTION)
                 {
                   rollladen[i].action=NOACTION;
                   switchRelay(i);
                 }
      }
    }
    rollladen[i].downPressed=state;
    
    Serial.println("going down:" + String(message.type));
  }
  else if (message.type == V_STOP) {
    {
      switch (rollladen[i].action)
      {
        case DOWNACTION: rollladen[i].action=NOACTION;
                       rollladen[i].actionStarttime=millis();
                       switchRelay(i);
                       break;

        case UPACTION: rollladen[i].action=NOACTION;
                       rollladen[i].actionStarttime=millis();
                       switchRelay(i);
                       break;
      }
    }
    Serial.println("stopping:" + String(message.type));
    } 
  }

I replaced the for loop with i = sensor.message , now i get "exit status 1
'i' was not declared in this scope". Do I have to declare the variable?

AWI

@ihtgtwtd int i = message.sensors ; would be the right syntax

ihtgtwtd

@AWI
thx, I tried that. it exits with 'const class MyMessage' has no member named 'sensors'.

AWI

@ihtgtwtd typo ... int i = message.sensor ; would be the right syntax, leave out the 's'

ihtgtwtd

@AWI
thanks, still small problems to figure out though.
when I send a command to rollershutter 1 then rollershutter 2 receives the command. I can not control shutter 1, only 2 and 3 (with the buttons of 1 and 2)

output in serial monitor is right and physical buttons work the right way too

is there a problem in the registration or am I missing something (again)?
the physical buttons work the right way.

// Enable debug prints to serial monitor
#define MY_DEBUG
// Enable and select radio type attached
#define MY_RADIO_NRF24
// Enable repeater functionality for this node
#define MY_REPEATER_FEATURE

#include <MySensors.h>
#include <SPI.h>

// Rollladensteuerung by jurs for German Arduino-Forum
#define BUTTONPRESSED LOW
#define RELAYACTIVE LOW

MyMessage sensorMsg0(0, V_DIMMER);
MyMessage sensorMsg1(1, V_DIMMER);
MyMessage sensorMsg2(2, V_DIMMER);

enum {NOACTION, UPACTION, DOWNACTION};

struct roll_t {
  byte downPin;
  byte upPin;
  boolean downPressed;
  boolean upPressed;
  byte action;
  unsigned long actionStarttime;
  unsigned long actionTimeout;
  byte relayOnePin;
  byte relayTwoPin;
};

roll_t rollladen[] = {
  {2, 3, false, false, NOACTION, 0, 60000L, A0, A1}, // Button-Pins 2, 3, Relay-Pins A0, A1, Timeout 60 secons
  {4, 5, false, false, NOACTION, 0, 45000L, A2, A3}, // Button-Pins 4, 5, Relay-Pins A2, A3, Timeout 45 secons
  {6, 7, false, false, NOACTION, 0, 45000L, A4, A5}, // Button-Pins 6, 7, Relay-Pins A4, A5, Timeout 45 secons
};

#define ANZAHLROLLLADEN sizeof(rollladen)/sizeof(rollladen[0])


void setup()
{
  Serial.begin(115200);
  for (int i = 0; i < ANZAHLROLLLADEN; i++)
  {
    if (BUTTONPRESSED == HIGH)
    {
      pinMode(rollladen[i].downPin, INPUT);
      pinMode(rollladen[i].upPin, INPUT);
    }
    else
    {
      pinMode(rollladen[i].downPin, INPUT_PULLUP);
      pinMode(rollladen[i].upPin, INPUT_PULLUP);
    }
    if (RELAYACTIVE == LOW)
    {
      digitalWrite(rollladen[i].relayOnePin, HIGH);
      digitalWrite(rollladen[i].relayTwoPin, HIGH);
    }
    pinMode(rollladen[i].relayOnePin, OUTPUT);
    pinMode(rollladen[i].relayTwoPin, OUTPUT);
  }
}


void switchRelay(byte i)
{
  Serial.print("Schalte Rolladen-");
  Serial.print(i);
  switch (rollladen[i].action)
  {
    case NOACTION: // STOP
      digitalWrite(rollladen[i].relayOnePin, !RELAYACTIVE);
      digitalWrite(rollladen[i].relayTwoPin, !RELAYACTIVE);
      Serial.println(" STOP");
      break;
    case UPACTION: // UP
      digitalWrite(rollladen[i].relayOnePin, RELAYACTIVE);
      digitalWrite(rollladen[i].relayTwoPin, !RELAYACTIVE);
      Serial.println(" UP");
      break;
    case DOWNACTION: // DOWN
      digitalWrite(rollladen[i].relayOnePin, !RELAYACTIVE);
      digitalWrite(rollladen[i].relayTwoPin, RELAYACTIVE);
      Serial.println(" DOWN");
      break;
  }
}



void loop(void)
{
  byte state;
  for (int i = 0; i < ANZAHLROLLLADEN; i++)
  {
    // Prüfen, ob Down gedrückt wurde
    state = digitalRead(rollladen[i].downPin);
    if (BUTTONPRESSED == LOW) state = !state;
    if (state && !rollladen[i].downPressed)
    {
      switch (rollladen[i].action)
      {
        case NOACTION: rollladen[i].action = DOWNACTION;
          rollladen[i].actionStarttime = millis();
          switchRelay(i);
          break;
        default: if (rollladen[i].action != NOACTION)
          {
            rollladen[i].action = NOACTION;
            switchRelay(i);
          }
      }
    }
    rollladen[i].downPressed = state;

    // Prüfen, ob Up gedrückt wurde
    state = digitalRead(rollladen[i].upPin);
    if (BUTTONPRESSED == LOW) state = !state;
    if (state && !rollladen[i].upPressed)
    {
      switch (rollladen[i].action)
      {
        case NOACTION: rollladen[i].action = UPACTION;
          rollladen[i].actionStarttime = millis();
          switchRelay(i);
          break;
        default: if (rollladen[i].action != NOACTION)
          {
            rollladen[i].action = NOACTION;
            switchRelay(i);
          }
      }
    }
    rollladen[i].upPressed = state;

    // Prüfen auf Timeout
    if (rollladen[i].action != NOACTION && millis() - rollladen[i].actionStarttime >= rollladen[i].actionTimeout)
    {
      rollladen[i].action = NOACTION;
      switchRelay(i);
    }
  }
  delay(5); // kleines Delay zum Entprellen der Buttons
}

void presentation()
{

  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Test", "1.0");

  // Fetch relay status
  for (int sensor = 1, pin = A0; sensor <= ANZAHLROLLLADEN; sensor++, pin++) {

    // Register all sensors to gw (they will be created as child devices)
    present(sensor, S_COVER);
    // Then set relay pins in output mode
    pinMode(pin, OUTPUT);
  }
}


void receive(const MyMessage &message) {
  byte state;
  int i = message.sensor ;

  if (message.type == V_UP) {
    {
      switch (rollladen[i].action)
      {
        case NOACTION: rollladen[i].action = UPACTION;
          rollladen[i].actionStarttime = millis();
          switchRelay(i);
          break;
        default: if (rollladen[i].action != NOACTION)
          {
            rollladen[i].action = NOACTION;
            switchRelay(i);
          }

      }
    }
    rollladen[i].upPressed = state;

    Serial.println("going up:" + String(message.type));
  }
  else if (message.type == V_DOWN) {
    {
      switch (rollladen[i].action)
      {
        case NOACTION: rollladen[i].action = DOWNACTION;
          rollladen[i].actionStarttime = millis();
          switchRelay(i);
          break;
        default: if (rollladen[i].action != NOACTION)
          {
            rollladen[i].action = NOACTION;
            switchRelay(i);
          }
      }
    }
    rollladen[i].downPressed = state;

    Serial.println("going down:" + String(message.type));
  }
  else if (message.type == V_STOP) {
    {
      switch (rollladen[i].action)
      {
        case DOWNACTION: rollladen[i].action = NOACTION;
          rollladen[i].actionStarttime = millis();
          switchRelay(i);
          break;

        case UPACTION: rollladen[i].action = NOACTION;
          rollladen[i].actionStarttime = millis();
          switchRelay(i);
          break;
      }
    }
    Serial.println("stopping:" + String(message.type));
  }
}

hope it's clear what I mean. It is a bit weird...

AWI

@ihtgtwtd that is caused in the presentation part of your routine. You did not create a switch for shutter 0. (started with 1)

ihtgtwtd

well thanks, I already tried that because it looked suspicious
but i was sending on switch 1 in domoticz and did not create a switch for 0.

So it seems this thing works, thanks again for your help and the patience to deal with my noob questions

problem with implementation of my sensors in rollershutter sketch

Suggested Topics

Day 1 - Status report
Announcements • • hek

Forum Search not working?
Troubleshooting • • Gibber

Arduino nano and Uno in same My sensors network with NRF24L01+
Troubleshooting • • DIY89

Suddenly a Sensor is Missing, not the whole Node. (RPI Eth Gateway, HA)
Troubleshooting • • se-O-matic

Extraneous info in Debug log
Troubleshooting • debug log • • Gibber

Echo request is not set
Troubleshooting • • kamilb85

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

problem with implementation of my sensors in rollershutter sketch

Suggested Topics

Day 1 - Status report Announcements • • hek

Forum Search not working? Troubleshooting • • Gibber

Arduino nano and Uno in same My sensors network with NRF24L01+ Troubleshooting • • DIY89

Suddenly a Sensor is Missing, not the whole Node. (RPI Eth Gateway, HA) Troubleshooting • • se-O-matic

Extraneous info in Debug log Troubleshooting • debug log • • Gibber

Echo request is not set Troubleshooting • • kamilb85

0Online

11.4kUsers

11.1kTopics

112.7kPosts

Day 1 - Status report
Announcements • • hek

Forum Search not working?
Troubleshooting • • Gibber

Arduino nano and Uno in same My sensors network with NRF24L01+
Troubleshooting • • DIY89

Suddenly a Sensor is Missing, not the whole Node. (RPI Eth Gateway, HA)
Troubleshooting • • se-O-matic

Extraneous info in Debug log
Troubleshooting • debug log • • Gibber

Echo request is not set
Troubleshooting • • kamilb85

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts