MySensors Raspberry port suggestions

[marceloaqno]

@emc2 I appreciate the offer for the adapter, but my country's post is a little complicated (to say the least).

@hawk_2050 /dev/ttyUSBMySensorsGateway (or any other parameter you pass to --my-serial-pty) is a symbolic link:

$ ls -lah /dev/ttyMySensorsGateway
lrwxrwxrwx 1 root root 10 Sep 16 12:39 /dev/ttyMySensorsGateway -> /dev/pts/2

In this case it is pointing to /dev/pts/2 but can vary, and it's the one who holds the specified group ownership.

[emc2]

@marceloaqno Up to you. I don't mind giving it a shot, if I send you the pcb alone it will fit in a regular letter and should not even have to go through customs etc. Worst case scenario it won't reach you.

[ikkeT]

@marceloaqno , I assume your link for the wiring pinout behind the link is for Raspi 1 A+ with 26 pin header? Or for which version?

I'd like to try this with raspi 2 B, would you have instructions how to wire it?

Raspi2:

Raspi1:

Thanks

[ikkeT]

No, looking it again, it's vice versa, so yours is for Raspi2, right?

[ikkeT]

So this 1.6 pinout would still apply? https://forum.mysensors.org/topic/2437/step-by-step-procedure-to-connect-the-nrf24l01-to-the-gpio-pins-and-use-the-raspberry-as-a-serial-gateway-mysensors-1-x

[marceloaqno]

@ikkeT yes, these are the default pins.
(SCK = 23, MISO = 21, MOSI = 19, CS = 24, CE = 22)

[ikkeT]

Yahooo! It works, finally. I bet my problem was Raspi1 all along. I never realized the pinouts in github were for raspi with 40 pins, b+/2/3. Thanks!

[marceloaqno]

@ikkeT it should also work for Raspi1, I got one running fine here.

[ikkeT]

OK, then I just screwed up something. Thanks for the info, so I know I can do this also with my old raspi one day.

[marceloaqno]

Update: Added support for status leds (RX/TX/ERR), you can enable it in examples_linux/mysGateway.cpp file.

[ikkeT]

Continuing the learning here, new questions... Thanks so far, I've now got the temp/hum/door messages sent and received from sensebender micro to raspi2. The next thing I would like to do is to send the messages as mqtt to the next box hosting some controller.

How to get the mysGateway to send the stuff forward as mqtt? I tried to look into Makefile, MyConfig.h and such, but didn't quite figure out yet how to do that. Any pointers?

So I'd like to have the following: sensebender -> radio -> raspi2 -> some box hosting the controller. Perhaps even outside of home, so routable traffic e.g. to OpenShift.com.

Should I now somehow configure and build mysGateway to send stuff as MQTT, or pipe the traffic somehow to mqtt like mosqitto? How is this normally done if the controller server is not running on the gateway Raspi?

Thanks for the patience, I'm just getting into all this interesting stuff :)

[mfalkvidd]

@ikkeT I haven't tried but using nodered should be fairly simple and very flexible. This discussion might be useful: https://forum.mysensors.org/topic/2802/flow-to-turn-serialgateway-into-mqtt-serialgateway/

[hawk_2050]

@ikkeT you can build the Raspberry Pi mysGateway as either Serial, Ethernet or MQTT by using appropriate commandline parameters with the configure script. Just do ./configure --help and you'll get a list of all the options available. Once you've chosen your options and run configure then you 'make'. An example of a set of options that will generate an MQTT Gateway is:
./configure --my-debug=enable --my-gateway=mqtt --my-rf24-channel=100 --my-rf24-pa-level=RF24_PA_LOW --my-controller-ip-address=127,0,0,1 --my-port=1883
--my-mqtt-client-id=MyGW2 --my-mqtt-publish-topic-prefix="MyGW2out" --my-mqtt-subscribe-topic-prefix="MyGW2in"

In this case my MQTT Broker is Mosquitto and is on the same Raspberry Pi hence the use of 127,0,0,1 for the specified --my-controller-ip-address. Change that as appropriate to your intended setup.

Hope that helps.

[wergeld]

@marceloaqno I have been trying to build this out by first building the RF24 library using the following:

git clone https://github.com/TMRh20/RF24.git
cd RF24
make
sudo make install

However, this fails on the make command:

Makefile:17: Makefile.inc: No such file or directory
[Running configure]
[SECTION] Detecting arm compilation environment.
  [OK] arm-linux-gnueabihf-gcc detected.
  [OK] arm-linux-gnueabihf-g++ detected.
[SECTION] Detecting target machine.
[OK] machine detected: SoC=BCM2836, Type=RPi2, CPU=armv7l.
[SECTION] Detecting DRIVER
  [OK] DRIVER detected:RPi.
[SECTION] Detecting OS.
  [INFO] OS detected:LINUX.
[SECTION] Preparing configuration.
[SECTION] Saving configuration.
[OK] Finished.
arm-linux-gnueabihf-g++ -fPIC -march=armv7-a -mtune=cortex-a7 -mfpu=neon-vfpv4 -mfloat-abi=hard -Ofast -Wall -pthread  -c RF24.cpp
cc1plus: error: bad value (cortex-a7) for -mtune switch
Makefile:40: recipe for target 'RF24.o' failed
make: *** [RF24.o] Error 1

I am not sure what to do here. Looks like the gcc does not support the cortex-a7? I am trying to run this on my RPi 2 B.

[marceloaqno]

@wergeld I'm not sure why you are having this error, perhaps your version of gcc it's old? Did you try to update it?
You can skip the installation of TMRh20/RF24, it is no longer necessary to build RPi port.

[wergeld]

@marceloaqno said:

@wergeld I'm not sure why you are having this error, perhaps your version of gcc it's old? Did you try to update it?
You can skip the installation of TMRh20/RF24, it is no longer necessary to build RPi port.

I have tried to update gcc but apt-get says it is already at latest version. I am upgrading to Jessie now as it has gcc 4.9 (I was running Wheezy with gcc 4.6).
Is there an updated build instruction set? I am planning on using this as a serial gateway with Domoticz on same RPi.

[ikkeT]

@hawk_2050 thanks for the reminder! I recalled it was somehow configurable, but I forgot it was through . /configure options. I'll try after getting pir working also.

[marceloaqno]

@wergeld I updated the building instructions:
https://forum.mysensors.org/topic/2759/mysensors-raspberry-port-suggestions/26

[wergeld]

@marceloaqno said:

@wergeld I updated the building instructions:
https://forum.mysensors.org/topic/2759/mysensors-raspberry-port-suggestions/26

Success! Upgraded to Jessie and build worked fine. Now to reconnect my radio to the RPi pins directly to test.

[wergeld]

@wergeld said:

@marceloaqno said:

@wergeld I updated the building instructions:
https://forum.mysensors.org/topic/2759/mysensors-raspberry-port-suggestions/26

Success! Upgraded to Jessie and build worked fine. Now to reconnect my radio to the RPi pins directly to test.

Okay, using an RPi2B upgraded to Jessie from Wheezy I have successfully built and set the mysGateway as a daemon. My configuration was:

./configure --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSBMySensorsGateway --my-rf24-pa-level=RF24_PA_LOW

This was immediately available in Domoticz under Hardware. I re-added the 2 nodes and away I went!

Full command list:

git clone https://github.com/marceloaqno/MySensors.git
cd MySensors
./configure --my-gateway=serial --my-serial-is-pty --my-serial-pty=/dev/ttyUSBMySensorsGateway --my-rf24-pa-level=RF24_PA_LOW
make
sudo make install
sudo mysGateway -b

In Domoticz it lists this gateway as running:
MySensors Gateway USB
Version: 2.0.1-beta

So far very happy with this setup. No wires and no extra arduino needed for serial gateway. Just the NRF+RPi interfacing via:
https://www.openhardware.io/view/100/Raspberry-PI-NRF24l01-hat