💬 Building an Ethernet Gateway
-
Hi, i i try compile GatewayW5100.ino on this page then result is compiler error:
Arduino: 1.6.12 (Windows 10), Board: "Arduino Nano, ATmega328"
In file included from C:\Users\M\Documents\Arduino\libraries\MySensors-master/drivers/RF24/RF24.cpp:23:0,
from C:\Users\M\Documents\Arduino\libraries\MySensors-master/MySensors.h:261, from C:\Users\M\AppData\Local\Temp\arduino_modified_sketch_502474\sketch_oct22a.ino:116:C:\Users\M\Documents\Arduino\libraries\MySensors-master/drivers/RF24/RF24.h:34:31: error: 'SPI_MODE0' was not declared in this scope
#define MY_RF24_SPI_DATA_MODE SPI_MODE0
^C:\Users\M\Documents\Arduino\libraries\MySensors-master/drivers/RF24/RF24.h:38:76: note: in expansion of macro 'MY_RF24_SPI_DATA_MODE'
SoftSPI<MY_SOFT_SPI_MISO_PIN, MY_SOFT_SPI_MOSI_PIN, MY_SOFT_SPI_SCK_PIN, MY_RF24_SPI_DATA_MODE> _SPI;
^C:\Users\M\Documents\Arduino\libraries\MySensors-master/drivers/RF24/RF24.h:38:97: error: template argument 4 is invalid
SoftSPI<MY_SOFT_SPI_MISO_PIN, MY_SOFT_SPI_MOSI_PIN, MY_SOFT_SPI_SCK_PIN, MY_RF24_SPI_DATA_MODE> _SPI;
^C:\Users\M\Documents\Arduino\libraries\MySensors-master/drivers/RF24/RF24.h:38:103: error: invalid type in declaration before ';' token
SoftSPI<MY_SOFT_SPI_MISO_PIN, MY_SOFT_SPI_MOSI_PIN, MY_SOFT_SPI_SCK_PIN, MY_RF24_SPI_DATA_MODE> _SPI;
^In file included from C:\Users\M\Documents\Arduino\libraries\MySensors-master/MySensors.h:261:0,
from C:\Users\M\AppData\Local\Temp\arduino_modified_sketch_502474\sketch_oct22a.ino:116:C:\Users\M\Documents\Arduino\libraries\MySensors-master/drivers/RF24/RF24.cpp: In function 'uint8_t RF24_spiMultiByteTransfer(uint8_t, uint8_t*, uint8_t, bool)':
C:\Users\M\Documents\Arduino\libraries\MySensors-master/drivers/RF24/RF24.cpp:44:24: error: request for member 'transfer' in '_SPI', which is of non-class type 'int'
uint8_t status = _SPI.transfer( cmd );
^C:\Users\M\Documents\Arduino\libraries\MySensors-master/drivers/RF24/RF24.cpp:47:18: error: request for member 'transfer' in '_SPI', which is of non-class type 'int'
status = _SPI.transfer( NOP ); ^C:\Users\M\Documents\Arduino\libraries\MySensors-master/drivers/RF24/RF24.cpp:49:24: error: request for member 'transfer' in '_SPI', which is of non-class type 'int'
} else status = _SPI.transfer(*current++);
^C:\Users\M\Documents\Arduino\libraries\MySensors-master/drivers/RF24/RF24.cpp: In function 'bool RF24_initialize()':
C:\Users\M\Documents\Arduino\libraries\MySensors-master/drivers/RF24/RF24.cpp:261:7: error: request for member 'begin' in '_SPI', which is of non-class type 'int'
_SPI.begin();
^exit status 1
Error compiling for board Arduino Nano.This report would have more information with
"Show verbose output during compilation"
option enabled in File -> Preferences.Could you please help?
Thanks.
If anyone answers @Marek-Běluša, please answer in https://forum.mysensors.org/topic/5159/ethernet-gateway-compile-error/ to avoid working in two different threads. Do not answer here.
@Marek-Běluša please do not post the same question in more than one place.
-
I've spent hours and hours to get the W5100 Ethernet Module working on my Arduino Nano board and unfortunately without success. I'm using the MySensors version 2.0 with the Arduino AVR Boards 1.6.15 installed. I don't understand the issue at all. I cannot ping W5100 should, not if I use a static IP or if I configure to use DHCP. I've tested it with and without the NRF24L01 Radio connected and no luck. I've checked the wires already 10 times. This is the wire-ring info:
W5100 <=> Arduino Nano
VDD <=> Pin 27 / +5V
NSS <=> Pin 13 / D10
MOSI <=> Pin 14 / D11
GND <=> Pin 4
SCK <=> Pin 16 / D13
MISO <=> Pin 15 / D12Is this the correct wire configuration? What else can I do to debug this?
On the W5100 I see the link led blinking on a regular basis almost at the same time as the Rx led, but I read that this HW issue and doesn't influence the behaviour of the ethernet board. Is this correct? If not, how to resolve this?
Looking forward to hints and tips as I'm completely lost on this topic.
-
I've spent hours and hours to get the W5100 Ethernet Module working on my Arduino Nano board and unfortunately without success. I'm using the MySensors version 2.0 with the Arduino AVR Boards 1.6.15 installed. I don't understand the issue at all. I cannot ping W5100 should, not if I use a static IP or if I configure to use DHCP. I've tested it with and without the NRF24L01 Radio connected and no luck. I've checked the wires already 10 times. This is the wire-ring info:
W5100 <=> Arduino Nano
VDD <=> Pin 27 / +5V
NSS <=> Pin 13 / D10
MOSI <=> Pin 14 / D11
GND <=> Pin 4
SCK <=> Pin 16 / D13
MISO <=> Pin 15 / D12Is this the correct wire configuration? What else can I do to debug this?
On the W5100 I see the link led blinking on a regular basis almost at the same time as the Rx led, but I read that this HW issue and doesn't influence the behaviour of the ethernet board. Is this correct? If not, how to resolve this?
Looking forward to hints and tips as I'm completely lost on this topic.
-
@mfalkvidd yes I've read that, even multiple times. I've check the wiring 10 times as well and cannot find a difference. Also changed to another W5100 board as well as a different Arduino Uno board to make sure it is not a board issue. The problem stays the same. What I've noticed as a difference is that my W5100 runs on 5V and not on 3.3V as indicated in the wiring table. Connecting the W5100 with 3.3V doesn't start (boot up) the board.
-
Just thought I'd mention that I've had good experience with adding a capacitor between GND and VCC for the ethernet module as well.
Same approach as for wiring the radio. https://www.mysensors.org/build/connect_radioPreviously had problems with GW disconnecting (Eth: disconnect) which is now reduced.
-
Same problem like Reza, same error messages AND I USING ethernet shield, ARDUINO MEGA AND nrf24
-
And using ARDUINO 1 the same problem.
0;255;3;0;9;Starting gateway (RNNGA-, 2.0.0)
0;255;3;0;9;TSM:INIT
0;255;3;0;9;!TSM:RADIO:FAIL
0;255;3;0;9;!TSM:FAILURE
0;255;3;0;9;TSM:PDT
0;255;3;0;9;TSM:INIT
0;255;3;0;9;!TSM:RADIO:FAIL
0;255;3;0;9;!TSM:FAILURE
0;255;3;0;9;TSM:PDT -
Had lots of issues getting this to work. The issue seems to be with the ethernet part, as I only have an ethernet board attached I removed the lines for the radio and the pin redirection. Still the code kept restarting all the time or just not being able to connect the controller.
AVR version of the Arduino 1.8.0 kit needs to be downgraded. I had 1.6.16 and downgraded to 1.6.11.
Open Arduino. Tools > Board: xxxxx > Boards manager... > Click "Arduino AVR Boards" > Select Version > 1.6.11
Recompile and you are good.
-
@LaMB95
For the moment, i don't think there is an howto regarding w5500 as we're mostly using w5100, but maybe you can find some infos in this topic https://forum.mysensors.org/topic/2901/my-ethernet-gateway-board-w5500 -
Hi All,
I have an ethernet gateway base on arduino Pro mini with NRF24L01 radio and Funding ethernet card with W5100 chips. (As per description of this page)
All works fine when I'm connected to it with Arduino IDE. Works for hours/days.
If I unplug the IDE (disconnect USB) and run it alone it stop working after for minutes or few hours.
I have only one sensor (temperature) to test. It send Temperature and battery level every 10s (testing). Led attached to Gateway to show the traffic lit up twice each time it receive the information from the sensor. The LED lit up twice like half a second when everything is fine. Easy to see.
When the issue starts, the led lit up time to time but very quickly, and even very difficult to see. Some time I can ping the Gateway, some time not.
Any idea from anybody ? -
The first one will not compile since the #include <SPI.h> is missing
-
Hello guys,
Can anyone help me with modify this to work with W5500 Ethernet module?
Please advice us what need to be modified and why it needs to be modified.
Thanks you very much.@WizarDEAD the information in https://forum.mysensors.org/topic/2901/my-ethernet-gateway-board-w5500 might be useful.
