Node dont connect to RaspBerry gateway

[keldandorin]

@gohan Changed radio on Rpi
and node log looks like this now, Forgot MY_ before node :smile:

0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
3 TSM:INIT
4 TSF:WUR:MS=0
11 TSM:INIT:TSP OK
13 TSM:INIT:STATID=2
18 TSF:SID:OK,ID=2
19 TSM:FPAR
55 TSF:MSG:SEND,2-2-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2063 !TSM:FPAR:NO REPLY
2065 TSM:FPAR
2101 TSF:MSG:SEND,2-2-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4108 !TSM:FPAR:NO REPLY
4110 TSM:FPAR
4146 TSF:MSG:SEND,2-2-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6153 !TSM:FPAR:NO REPLY
6155 TSM:FPAR
6191 TSF:MSG:SEND,2-2-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8198 !TSM:FPAR:FAIL
8199 TSM:FAIL:CNT=1
8201 TSM:FAIL:PDT

[keldandorin]

@keldandorin Looks like I get som data to GW now but it dosent connect. Node has ID 3

mysgw: TSF:MSG:BC
mysgw: TSF:MSG:FPAR REQ,ID=3
mysgw: TSF:CKU:OK,FCTRL
mysgw: TSF:MSG:GWL OK
mysgw: !TSF:MSG:SEND,0-0-3-3,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0
mysgw: TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
mysgw: TSF:MSG:BC
mysgw: TSF:MSG:FPAR REQ,ID=3
mysgw: TSF:CKU:OK,FCTRL
mysgw: TSF:MSG:GWL OK

[gohan]

Do you have cap on the radio?

[keldandorin]

@gohan yes

[keldandorin]

@keldandorin If I pars log from GW it says

Sent Message
Sender: 0
Last Node: 0
Next Node: 3
Destination: 3
Sensor Id: 255
Command: INTERNAL
Message Type:I_FIND_PARENT_RESPONSE
Payload Type: P_BYTE
Payload Length: 1
Signing: 0
Failed uplink counter: 0
Status: NACK (OK=success, NACK=no radio ACK received)
Payload: 0

Just like its acctualy responding to Node !
But the node dosent like the awnser

[keldandorin]

Hi guys, realy need som help here. Got my Rpi gateway up and running and logfile looks ok, see below.
have a working Node running with DTH22. (know its working sins its conenct to my Arduino GW)
Tryed to onfigured Node Id on node. Connecting to my RpiGW with MYScontroller and can see the gateway but no nodes connect.
Log on PRI looks like this
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG--Q,VER=2.1.1
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: Listening for connections on 0.0.0.0:5003
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
mysgw: TSF:MSG:BC
mysgw: TSF:MSG:FPAR REQ,ID=3
mysgw: TSF:CKU:OK,FCTRL
mysgw: TSF:MSG:GWL OK
mysgw: !TSF:MSG:SEND,0-0-3-3,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0

Log on Node like this
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
3 TSM:INIT
4 TSF:WUR:MS=0
11 TSM:INIT:TSP OK
13 TSM:INIT:STATID=3
14 TSF:SID:OK,ID=3
16 TSM:FPAR
52 TSF:MSG:SEND,3-3-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2059 !TSM:FPAR:NO REPLY
2061 TSM:FPAR
2097 TSF:MSG:SEND,3-3-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4104 !TSM:FPAR:NO REPLY
4106 TSM:FPAR
4142 TSF:MSG:SEND,3-3-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6149 !TSM:FPAR:NO REPLY
6151 TSM:FPAR
6187 TSF:MSG:SEND,3-3-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8194 !TSM:FPAR:FAIL
8195 TSM:FAIL:CNT=1
8197 TSM:FAIL:PDT

From my basic understanding it looks like the GW dont responding in the correct way or the node dont like the awnser. Anyone with more experince out there that can give me some ideas how to fix this.
Thx
/Håkan

[gohan]

The gateway is replying but node is not receiving. Where are you getting power for your nrf24 radio on the rpi? Are you using a capacitor ? size?

[keldandorin]

@gohan taking power from 3v3 pin number 1 an using capasitor that is 10uF

[gohan]

Other users reported a similar problem and they solved by using something like this (that's the one I have on my rpi) or any other similar voltage regulator + capacitor

[keldandorin]

@gohan had it running now for a cuple of hours and sudenly it registerd. No luck efter reboot though. Guess I have to order one of them Voltage regulators/capacitors....realy wish I hade one now in my Man Cave :joy:

[gohan]

I ordered them by mistake some time ago, but they turned out to be very useful 😂

[keldandorin]

@gohan had it running again for some time and at message1890739 It got connected again and seems to be able to send message to GW. But as you say its the GW sending part that dosent seems to work.

1890739 TSM:FPAR:OK
1890740 TSM:ID
1890742 TSM:ID:OK
1890744 TSM:UPL
1890749 TSF:MSG:SEND,3-3-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
1892756 TSM:UPL
1892761 TSF:MSG:SEND,3-3-0-0,s=255,c=3,t=24,pt=1,l=1,sg=0,ft=0,st=OK:1
1892768 TSF:MSG:READ,0-0-3,s=255,c=3,t=25,pt=1,l=1,sg=0:1
1892773 TSF:MSG:PONG RECV,HP=1
1892776 TSM:UPL:OK

[keldandorin]

@gohan You think one of this could solv it to.
http://www.ebay.com/itm/10pcs-LM350-LM350T-3A-Adjustable-Voltage-Regulator-TO-220-NS-/270934993534?hash=item3f14fbea7e:m:m1teKyPPDfS02DlKXI_oD1g

Using 5v as output insted and regulat it down to 3.3 v and capasitator on that.

Got them in local store :)

[gohan]

I suggested those modules because you can quickly swap the radio module, but that may work too. Pls post back your results