Node dont connect to RaspBerry gateway

gohan

It downloaded the development branch instead of the stable one. @hek is it normal?

hek

Yes, development is the default branch (and the only one accepting PRs etc).

If you want to switch to master after cloning the repo, do:

git checkout master

gohan

Could be worth adding that command to the guide 😉

hek

@gohan
What guide?
The rpi guide checks out master: https://www.mysensors.org/build/raspberry

The contribution guide is focused on creating pull requests, so it naturally uses the default (development).

gohan

Ah my bad, I didn't see the - - branch master at the end of the line as I'm on mobile 😌

Jeff Willecke

Try assigning a node ID. Sometimes controllers will provide an ID but the gateway will not. Currently it is using the ID of 255. I think the line of code to add to the sketch is

#define node_ID #

Where the # at the end is the number of your node. Any value between 1 and 254 should work.

keldandorin

@gohan hehe N00b misstake thougt --branch Master was referens that the rest downloaded master...have just started to try out git :)

keldandorin

OK got version 2.1.1 on place on Rpi deffined Node Id but still no luck connecting to Rpi GW :cry:

GW Log
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG--Q,VER=2.1.1
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: Listening for connections on 0.0.0.0:5003
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: TSF:MSG:READ,255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
mysgw: TSF:MSG:BC
mysgw: TSF:MSG:FPAR REQ,ID=255
mysgw: TSF:PNG:SEND,TO=0
mysgw: TSF:CKU:OK
mysgw: TSF:MSG:GWL OK
mysgw: TSF:MSG:SEND,0-0-255-255,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=OK:0
mysgw: TSF:MSG:READ,255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
mysgw: TSF:MSG:BC
mysgw: TSF:MSG:FPAR REQ,ID=255
mysgw: TSF:CKU:OK,FCTRL
mysgw: TSF:MSG:GWL OK

Node Log:
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
3 TSM:INIT
4 TSF:WUR:MS=0
11 TSM:INIT:TSP OK
13 TSM:FPAR
15 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2022 !TSM:FPAR:NO REPLY
2024 TSM:FPAR
2026 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4034 !TSM:FPAR:NO REPLY
4036 TSM:FPAR
4038 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6046 !TSM:FPAR:NO REPLY
6048 TSM:FPAR
6050 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8058 !TSM:FPAR:FAIL
8059 TSM:FAIL:CNT=1
8061 TSM:FAIL:PDT

Going to replace radio and try again.

gohan

Double check node ID, I don't see it in node log

keldandorin

@gohan Changed radio on Rpi
and node log looks like this now, Forgot MY_ before node :smile:

0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
3 TSM:INIT
4 TSF:WUR:MS=0
11 TSM:INIT:TSP OK
13 TSM:INIT:STATID=2
18 TSF:SID:OK,ID=2
19 TSM:FPAR
55 TSF:MSG:SEND,2-2-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2063 !TSM:FPAR:NO REPLY
2065 TSM:FPAR
2101 TSF:MSG:SEND,2-2-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4108 !TSM:FPAR:NO REPLY
4110 TSM:FPAR
4146 TSF:MSG:SEND,2-2-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6153 !TSM:FPAR:NO REPLY
6155 TSM:FPAR
6191 TSF:MSG:SEND,2-2-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8198 !TSM:FPAR:FAIL
8199 TSM:FAIL:CNT=1
8201 TSM:FAIL:PDT

keldandorin

@keldandorin Looks like I get som data to GW now but it dosent connect. Node has ID 3

mysgw: TSF:MSG:BC
mysgw: TSF:MSG:FPAR REQ,ID=3
mysgw: TSF:CKU:OK,FCTRL
mysgw: TSF:MSG:GWL OK
mysgw: !TSF:MSG:SEND,0-0-3-3,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0
mysgw: TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
mysgw: TSF:MSG:BC
mysgw: TSF:MSG:FPAR REQ,ID=3
mysgw: TSF:CKU:OK,FCTRL
mysgw: TSF:MSG:GWL OK

gohan

Do you have cap on the radio?

keldandorin

@gohan yes

keldandorin

@keldandorin If I pars log from GW it says

Sent Message
Sender: 0
Last Node: 0
Next Node: 3
Destination: 3
Sensor Id: 255
Command: INTERNAL
Message Type:I_FIND_PARENT_RESPONSE
Payload Type: P_BYTE
Payload Length: 1
Signing: 0
Failed uplink counter: 0
Status: NACK (OK=success, NACK=no radio ACK received)
Payload: 0

Just like its acctualy responding to Node !
But the node dosent like the awnser

keldandorin

Hi guys, realy need som help here. Got my Rpi gateway up and running and logfile looks ok, see below.
have a working Node running with DTH22. (know its working sins its conenct to my Arduino GW)
Tryed to onfigured Node Id on node. Connecting to my RpiGW with MYScontroller and can see the gateway but no nodes connect.
Log on PRI looks like this
mysgw: Starting gateway...
mysgw: Protocol version - 2.1.1
mysgw: MCO:BGN:INIT GW,CP=RNNG--Q,VER=2.1.1
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: Listening for connections on 0.0.0.0:5003
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1
mysgw: TSF:MSG:READ,3-3-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
mysgw: TSF:MSG:BC
mysgw: TSF:MSG:FPAR REQ,ID=3
mysgw: TSF:CKU:OK,FCTRL
mysgw: TSF:MSG:GWL OK
mysgw: !TSF:MSG:SEND,0-0-3-3,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0

Log on Node like this
0 MCO:BGN:INIT NODE,CP=RNNNA--,VER=2.1.1
3 TSM:INIT
4 TSF:WUR:MS=0
11 TSM:INIT:TSP OK
13 TSM:INIT:STATID=3
14 TSF:SID:OK,ID=3
16 TSM:FPAR
52 TSF:MSG:SEND,3-3-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2059 !TSM:FPAR:NO REPLY
2061 TSM:FPAR
2097 TSF:MSG:SEND,3-3-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4104 !TSM:FPAR:NO REPLY
4106 TSM:FPAR
4142 TSF:MSG:SEND,3-3-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6149 !TSM:FPAR:NO REPLY
6151 TSM:FPAR
6187 TSF:MSG:SEND,3-3-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8194 !TSM:FPAR:FAIL
8195 TSM:FAIL:CNT=1
8197 TSM:FAIL:PDT

From my basic understanding it looks like the GW dont responding in the correct way or the node dont like the awnser. Anyone with more experince out there that can give me some ideas how to fix this.
Thx
/Håkan

gohan

The gateway is replying but node is not receiving. Where are you getting power for your nrf24 radio on the rpi? Are you using a capacitor ? size?

keldandorin

@gohan taking power from 3v3 pin number 1 an using capasitor that is 10uF

gohan

Other users reported a similar problem and they solved by using something like this (that's the one I have on my rpi) or any other similar voltage regulator + capacitor

keldandorin

@gohan had it running now for a cuple of hours and sudenly it registerd. No luck efter reboot though. Guess I have to order one of them Voltage regulators/capacitors....realy wish I hade one now in my Man Cave :joy:

gohan

I ordered them by mistake some time ago, but they turned out to be very useful 😂

Node dont connect to RaspBerry gateway

23

11.7k

11.2k

113.1k