communicate is good for first time for relays and sensors but after some days will be weak and some time stop working !
-
i see communicate operation carefully for 3 days. because i can not use arduino serial monitor for 3 days (power on pc for 72 hours). so i see just T LED (transmit) on arduino in nodes (relay and repeater).
as I said before i use a relay for repeater and some sensors and other relay connect to gateway from this repeater node(because radio in repeater is strong).
so now i see, sensors is ok and send command from node to gateway with repeater.
but when i send a command from controller to repeater or other relay node(that use same repeater) i have error, i see LED in repeater dont blink when i send command from controller .generally when node want send command to controller connection between repeater and gateway is ok but when controller want send command to node (repeater node and other relay nodes) i have error. the T led on arduino in repeater and other relay node dont blink ( not always. but most time, for example every 20 or 30 command one command is send but with a most delay for exapmle 5 or 10 second.) this is strange because first days work well !
for controller i use a nrf+pa and use pa_max for all node and gateway.
i use 5v pinout on raspberry for radio . and use a regulator adapter (ams1117) with 100u cap for radio.can you help me to found problem ? is this related to gateway (v2.2.0 for 5 month ago) or repeater (sketch) or chinese devices(hardware) ?
thank you
-
try update to latest libray first thing, then try also power other power levels pa_low and pa_high (some modules don't work well with pa_max)
-
try update to latest libray first thing, then try also power other power levels pa_low and pa_high (some modules don't work well with pa_max)
-
I just clone the repository, stop the mysgw service, compile and run the install process if it doesn't start automatically on boot (maybe there is a better way to do it)
-
-
-
-
@gohan said in communicate is good for first time for relays and sensors but after some days will be weak and some time stop working !:
maybe the voltage regulator? try to swap that too. It is all a matter of trial and error.
thank you . i will change the regulator with a better regulator.and i test again . thank you
-
also swapping things between gateway and repeater and see if problem follows the part or not.
-
to test it out you would need at least 2 nodes connected to gateway and 2 to the repeater and test where the node to node communication between all nodes and see which is having problems. The best solution would be to use more than the 2 parts you currently have just to exclude both of them being faulty. I am really running out of options.
-
to test it out you would need at least 2 nodes connected to gateway and 2 to the repeater and test where the node to node communication between all nodes and see which is having problems. The best solution would be to use more than the 2 parts you currently have just to exclude both of them being faulty. I am really running out of options.
@gohan said in communicate is good for first time for relays and sensors but after some days will be weak and some time stop working !:
to test it out you would need at least 2 nodes connected to gateway and 2 to the repeater and test where the node to node communication between all nodes and see which is having problems. The best solution would be to use more than the 2 parts you currently have just to exclude both of them being faulty. I am really running out of options.
ok thank you . i will test this .
-
to test it out you would need at least 2 nodes connected to gateway and 2 to the repeater and test where the node to node communication between all nodes and see which is having problems. The best solution would be to use more than the 2 parts you currently have just to exclude both of them being faulty. I am really running out of options.
@gohan
for test first i change my regulator in controller and repeater,use LF33 instead of
ams1117. but problem dont solve.now i put some relay near controller and connect directly to controller and i will test when there is problem and relay with repeater dont work, so relay that directly connect to controller have same problem or not ! -
to test it out you would need at least 2 nodes connected to gateway and 2 to the repeater and test where the node to node communication between all nodes and see which is having problems. The best solution would be to use more than the 2 parts you currently have just to exclude both of them being faulty. I am really running out of options.
