nRF5 action!

d00616

@NeverDie said in nRF5 Bluetooth action!:

I had wrongly assumed that the "sleep(...)" command would sleep the radio. Thanks for pointing out my error. How/when is it that Mysensors puts the radio to sleep? Does it just happen automatically at the end of every sending/receiving?

We are both not 100% correct The hwSleep() function doesn't disable the radio, but the sleep() function does it, when MY_SENSOR_NETWORK is defined.

After Sleep transportReInitialise() is called. Then you have to initialize RadioHead again.

NeverDie

@d00616 said in nRF5 Bluetooth action!:

After Sleep transportReInitialise() is called. Then you have to initialize RadioHead again.

So, even with RAM retention active while sleeping, each time the radio is awoken, it needs to be re-initialized?

d00616

@NeverDie said in nRF5 Bluetooth action!:

So, even with RAM retention active while sleeping, each time the radio is awoken, it needs to be re-initialized?

The Radio has to be initialized after power down. This doesn't depend on RAM retention.

NeverDie

According to Table 39 of the mRF52832 datasheet, there is only one radio state resembling sleep, and that is the DISABLED radio state where "No operations are going on inside the radio and the power consumption is at a minimum."

Apparently the radio is disabled through register TASKS_DISABLE, offset 0x010, Disable RADIO, as indicated by Table 41 register overview.

NeverDie

But how exactly does one read or write to these registers? It looks like a quite different arrangement than writing to registers for an nRF24 or an RFM69 or a LoRa chip.

d00616

@NeverDie said in nRF5 Bluetooth action!:

But how exactly does one read or write to these registers? It looks like a quite different arrangement than writing to registers for an nRF24 or an RFM69 or a LoRa chip.

You have to include nrf.h. To disable the radio, you can do this:

https://github.com/mysensors/MySensors/blob/development/drivers/NRF5/Radio_ESB.cpp#L264

If your transmitting power is 0dbm, then "TX only run current PRF = 0dBm" with 11.6 mA is near the calculated current, when the radio stays in TX mode after sending the data.

NeverDie

@d00616
Will this block of code guarantee that the radio is disabled?

  Serial.println("Testing whether radio is disabled...");
  Serial.print("NRF_RADIO->EVENTS_DISABLED=");
  Serial.println(NRF_RADIO->EVENTS_DISABLED);
  while (!(NRF_RADIO->EVENTS_DISABLED)) {
    Serial.print("NRF_RADIO->EVENTS_DISABLED=");
    Serial.println(NRF_RADIO->EVENTS_DISABLED);
    NRF_RADIO->TASKS_DISABLE = 1;  //sleep the radio
  }
  Serial.println("Radio disabled.");

d00616

@NeverDie said in nRF5 Bluetooth action!:

Will this block of code guarantee that the radio is disabled?

This one is better:

if (NRF_RADIO->STATE != RADIO_STATE_STATE_Disabled) {
	NRF_RADIO->TASKS_DISABLE = 1;
}

d00616

@rmtucker said in nRF5 Bluetooth action!:

Yes being able to change the prescaler dynamically would help a great deal as 125ms / 582.542 hours is not really useful for most applications with a 250ms overrun.

The sleep() function is now more precise for sleeping <512s:

https://github.com/mysensors/MySensors/pull/909

The PR is waiting for merge.

NeverDie

@d00616
That works. Thanks!

What's the best way to awaken the radio after sleeping it though? I've tried:

    NRF_RADIO->TASKS_START  = 1;  //awaken the radio

and

    NRF_RADIO->TASKS_TXEN  = 1;  //awaken the radio

and neither seems to have an effect. The radio stays disabled.

d00616

@NeverDie said in nRF5 Bluetooth action!:

What's the best way to awaken the radio after sleeping it though? I've tried:

This depends on the implementation. Sorry, at the moment I have not time to look into the RadioHead code in that detail. You can try to initialize the library again.

d00616

@NeverDie Here is a snippet to dump all registers, hope it's help to analyze whats going wrong with RadioHead:

Serial.print("NRF_RADIO->EVENTS_READY  ");
Serial.println(NRF_RADIO->EVENTS_READY, HEX);
Serial.print("NRF_RADIO->EVENTS_ADDRESS  ");
Serial.println(NRF_RADIO->EVENTS_ADDRESS, HEX);
Serial.print("NRF_RADIO->EVENTS_PAYLOAD  ");
Serial.println(NRF_RADIO->EVENTS_PAYLOAD, HEX);
Serial.print("NRF_RADIO->EVENTS_END  ");
Serial.println(NRF_RADIO->EVENTS_END, HEX);
Serial.print("NRF_RADIO->EVENTS_DISABLED  ");
Serial.println(NRF_RADIO->EVENTS_DISABLED, HEX);
Serial.print("NRF_RADIO->EVENTS_DEVMATCH  ");
Serial.println(NRF_RADIO->EVENTS_DEVMATCH, HEX);
Serial.print("NRF_RADIO->EVENTS_DEVMISS  ");
Serial.println(NRF_RADIO->EVENTS_DEVMISS, HEX);
Serial.print("NRF_RADIO->EVENTS_RSSIEND  ");
Serial.println(NRF_RADIO->EVENTS_RSSIEND, HEX);
Serial.print("NRF_RADIO->EVENTS_BCMATCH  ");
Serial.println(NRF_RADIO->EVENTS_BCMATCH, HEX);
Serial.print("NRF_RADIO->CRCSTATUS  ");
Serial.println(NRF_RADIO->CRCSTATUS, HEX);
Serial.print("NRF_RADIO->RXMATCH  ");
Serial.println(NRF_RADIO->RXMATCH, HEX);
Serial.print("NRF_RADIO->RXCRC  ");
Serial.println(NRF_RADIO->RXCRC, HEX);
Serial.print("NRF_RADIO->DAI  ");
Serial.println(NRF_RADIO->DAI, HEX);
Serial.print("NRF_RADIO->PACKETPTR  ");
Serial.println(NRF_RADIO->PACKETPTR, HEX);
Serial.print("NRF_RADIO->FREQUENCY  ");
Serial.println(NRF_RADIO->FREQUENCY, HEX);
Serial.print("NRF_RADIO->TXPOWER  ");
Serial.println(NRF_RADIO->TXPOWER, HEX);
Serial.print("NRF_RADIO->MODE  ");
Serial.println(NRF_RADIO->MODE, HEX);
Serial.print("NRF_RADIO->PCNF0  ");
Serial.println(NRF_RADIO->PCNF0, HEX);
Serial.print("NRF_RADIO->PCNF1  ");
Serial.println(NRF_RADIO->PCNF1, HEX);
Serial.print("NRF_RADIO->BASE0  ");
Serial.println(NRF_RADIO->BASE0, HEX);
Serial.print("NRF_RADIO->BASE1  ");
Serial.println(NRF_RADIO->BASE1, HEX);
Serial.print("NRF_RADIO->PREFIX0  ");
Serial.println(NRF_RADIO->PREFIX0, HEX);
Serial.print("NRF_RADIO->PREFIX1  ");
Serial.println(NRF_RADIO->PREFIX1, HEX);
Serial.print("NRF_RADIO->TXADDRESS  ");
Serial.println(NRF_RADIO->TXADDRESS, HEX);
Serial.print("NRF_RADIO->RXADDRESSES  ");
Serial.println(NRF_RADIO->RXADDRESSES, HEX);
Serial.print("NRF_RADIO->CRCCNF  ");
Serial.println(NRF_RADIO->CRCCNF, HEX);
Serial.print("NRF_RADIO->SHORTS  ");
Serial.println(NRF_RADIO->SHORTS, HEX);

NeverDie

@d00616
I did a bit more poking around, and I've confirmed that there's no need to re-enable the radio before transmitting. Apparently doing the transmission and returning to disabled mode happens automatically. In fact, I think this is the expected behavior, as indicated by Figure 35 of the datasheet.

NeverDie

So, under this theory, the only time when the radio is not disabled is when it is actively transmitting or receiving. There's no need to manually disable it, because that appears to happen automatically anyway.

NeverDie

So, to move forward with this, I took a super-stripped down nRF52832, and loaded it with a super stripped down sketch that never initializes the radio and pretty much just jumps directly into a long RTC 12 hour slumber using the MySensors sleep routine. Measuring the current drawn while in that slumber using a uCurrent Gold, I'm reading about 9.3ua. So, to confirm that, I'm running the same stripped down setup from a 10F supercap, and I'll see at what rate the supercap voltage drops with time, and whether that appears to agree or not with these initial measurements.

Hopefully the current draw will remain low, and there will be no surprises. In that case, I'll add stuff back in until I find the culprit that was previously causing the higher current draw.

rmtucker

@NeverDie
I can not understand why you are drawing 9.4uA in the first place?.
My nrf51822 seems to consistently only draw 4-5uA with no strip down of software when in mysensors sleep mode.
Fair enough i have not got your measurement equipment but i don,t see it being that far away.
The data sheets seem to point to under 5uA.

NeverDie

@rmtucker said in nRF5 Bluetooth action!:

I can not understand why you are drawing 9.4uA in the first place?.

Yes, it is puzzling. I don't have a good answer as to why it measures so high. Maybe the crystal oscillator? What else is there that might be causing it?

NeverDie

After this initial run completes, I'll try reprogramming it to use the internal resonnator instead and see if that makes any difference.

NeverDie

Indeed, reprogramming the Ebyte nRF52832 to use the internal oscillator dropped the sleep current consumption down to 5.4ua.

I wonder whether physically removing the crystal oscillator would result in additional savings, or if that's as low as it goes?

I also wonder whether the datasheet cheats a bit by not counting the current consumed by the external crystal oscillator when that's being used? Otherwise, I don't see how Nordic can claim a <2ua sleep current for the nRF52832.

rmtucker

@NeverDie

Stranger still my 4-5uA is using the external crystal??.

NeverDie

I have to amend what I just said, because I took a measurement short-cut that in retrospect I shouldn't have: namely, I did the measurements on two different modules.

I went back and changed the 5.4ua module using the RC internal oscillator to use the external crystal oscillator, and it measures about the same.

So... The difference I was reading was a difference in the way the two modules measure. I'm not sure why one reads higher than the other, except perhaps that I didn't clean the solder flux off the higher reading module, and I did clean off the solder flux on the lower reading module.

I'll try cleaning the solder flux off the higher reading module and see if that drops the current consumed.

NeverDie

I cleaned off the solder flux and... no real difference. Go figure. Maybe it's just random variation among the Ebyte Modules? I guess I'll have to wire up more of them and see how they all compare.

Nca78

@NeverDie did you select the option with internal crystal ? 1s accuracy after 12h like you said before sounds more like a precise external crystal than an internal one.

NeverDie

@Nca78 said in nRF5 Bluetooth action!:

@NeverDie did you select the option with internal crystal ? 1s accuracy after 12h like you said before sounds more like a precise external crystal than an internal one.

Up until today I was using just the external crystal on the Ebyte nRF52832's. It was only for comparison purposes of current consumption that today I switched to the internal resonator. It's about the same current consumption. Maybe if I now remove the external crystal, it will save some current? I just don't know.

d00616

@rmtucker said in nRF5 Bluetooth action!:

I can not understand why you are drawing 9.4uA in the first place?.
My nrf51822 seems to consistently only draw 4-5uA with no strip down of software when in mysensors sleep mode.

While developing the nRF5 port, I had no chance to measure the current of the nRF52 accurate. With my original nRF51 dev kit I I have a sleeping current matching the data sheet.

Now I can measure currents in the µA range. With all nRF52 I have, I measured sleeping currents around 10µA. This is to much. We have to see 2-3µA. I have no original nRF52832 dev kit to compare. The reason of this sleeping current can be either an error in the layout or there is a component which is not required in active state while sleeping.

At the moment I have no time to analyse this. There is a bug in the radio code, which I have to fix. When transport debug is disabled no packages are received. In my opinion this has more priority.

Koresh

@NeverDie Just my two cents. Leakage current through non ideal capacitors can be 1-10uA.

NeverDie

@NeverDie said in nRF5 Bluetooth action!:

So, to move forward with this, I took a super-stripped down nRF52832, and loaded it with a super stripped down sketch that never initializes the radio and pretty much just jumps directly into a long RTC 12 hour slumber using the MySensors sleep routine. Measuring the current drawn while in that slumber using a uCurrent Gold, I'm reading about 9.3ua. So, to confirm that, I'm running the same stripped down setup from a 10F supercap, and I'll see at what rate the supercap voltage drops with time, and whether that appears to agree or not with these initial measurements.

Hopefully the current draw will remain low, and there will be no surprises. In that case, I'll add stuff back in until I find the culprit that was previously causing the higher current draw.

It turns out that the culprit was the mere act of using pinmode to designate a pin as an input pin, even if it's not connected to anything. Then, during sleep, the current consumption is an order of magnitude higher. This is quite different behavior than on, say, an Arduino pro mini, where the input pins are high impedance and there's neglible current draw.

Not sure what to do about it though. Any ideas?

NeverDie

The same sort of thing happens if pinmode is used to designate a pin as an output pin--again, even if nothing is connected to it.

This is a potential show stopper. This module is useless to me if I can't connect it to anything.

As a workaround, is there some way to designate a pin as undefined again after having used pinmode to define it as either an input pin or an output pin?

NeverDie

Well, setting the pinmode to OUTPUT and then digitalwriting it to LOW seems to help considerably--at least when it's not connected to anything.

[Edit: Setting it to HIGH also helps similarly.]

NeverDie

Anyhow, I'm relieved that the radio isn't the source of these power drain problems. This pinmode stuff is a bummer, but it looks like I can at least partially work around it.

d00616

@NeverDie said in nRF5 Bluetooth action!:

Well, setting the pinmode to OUTPUT and then digitalwriting it to LOW seems to help considerably--at least when it's not connected to anything.
[Edit: Setting it to HIGH also helps similarly.]

Thank's. I check this after I fixed the Radio.

Actually, I have this board running. I measure a voltage of 0.13mV=6,6µA at the shunt with a simple sleep sketch. When I switch two pins into INPUT_PULLUP, then I measure 0.15mV==7,5µA.

When I switch on the LED then I measure 12.75mV == 0,6375mA, One pin in OUTPUT_H1H0 mode. With LED off I measure 0.15mV==7,5µA.

My MCU is nRF52832 QFAAB0 1615AX

P.S.: I have no documentation about the board. When I measure the boards current, then I have an shunt factor of 22,5. I think calculating with 20 is ok.

NeverDie

@d00616
Thanks! I just now ordered one of your boards so that in the future we can share a common platform for comparing numbers.
https://www.aliexpress.com/item/NRF52832-Mini-Development-Board-Gold-Core-board-Wireless-Bluetooth-Transceiver-Module/32798618219.html?spm=2114.search0204.3.1.GUmybP&ws_ab_test=searchweb0_0,searchweb201602_4_10152_10065_10151_10130_5490020_10068_5430020_5410020_10307_10137_10060_10155_10154_10333_10334_10056_5370011_10335_10055_10336_10054_10059_10332_100031_10099_5400020_10103_10102_10052_10053_10107_10050_10142_10051_10324_10325_5380020_10326_5390020_10084_10083_10080_10082_10081_10178_10110_10111_10112_10113_10114_10312_10313_10314_10316_10078_10079_10073_5420011-10332_10333,searchweb201603_5,ppcSwitch_4_ppcChannel&btsid=78a27a2f-4aa5-49a0-a538-502a2c86d8f2&algo_expid=598ae4bb-6401-4529-89ad-6e8d8a90af12-0&algo_pvid=598ae4bb-6401-4529-89ad-6e8d8a90af12&transAbTest=ae803_3

[By the way, I did my measurements on an Ebyte nRF52832 module]

scalz

in that case, you need to set it as a floating input i think, like it's generally at reset.
In datasheet, section 20 (p111), is explained how works the GPIO. You have a Bit for disconnecting it. See the PIN_CNF[n] registers. For instance, p.140, you can see how it looks for the P0.10, and the Bit 1.
This should do the job..

d00616

@NeverDie said in nRF5 Bluetooth action!:

Thanks! I just now ordered one of your boards so that in the future we can share a common platform for comparing numbers.

Ok. I have measured my Ebyte with the same sketch and in the µA range of my VC165 multimeter. Sleep current is 9.9µA with two ports in INPUT_PULLUP and one Port in OUTPUT_H0H1 mode. (b.t.w. this module costs actually 3,82€)

@scalz said in nRF5 Bluetooth action!:

in that case, you need to set it as a floating input i think, like it's generally at reset.
In datasheet, section 20 (p111), is explained how works the GPIO. You have a Bit for disconnecting it. See the PIN_CNF[n] registers. For instance, p.140, you can see how it looks for the P0.10, and the Bit 1.
This should do the job..

Should I add a DISCONNECTED mode to hwPinMode()?

NeverDie

@d00616 said in nRF5 Bluetooth action!:

Sleep current is 9.9µA with two ports in INPUT_PULLUP and one Port in OUTPUT_H0H1 mode....

Ah, maybe that's part of the difference. I was doing just:

pinMode(ALPHA_PIN, INPUT)
pinMode(BETA_PIN, OUTPUT)

because that's how I would have done it on an Arduino. Should we instead always use INPUT_PULLUP and OUTPUT_H0H1 instead?

rmtucker

@NeverDie
Should be

hwPinMode(DIGITAL_INPUT_SENSOR, INPUT_PULLUP);

According to NRF5 platform

NeverDie

Thanks! Somehow didn't remember that.

So, as suggested by @scalz what is some example code that can be used to "disconnect" the pin later?

rmtucker

@NeverDie
He has not added that facility yet,i think he asked you if you wanted it adding to the code?

NeverDie

@rmtucker said in nRF5 Bluetooth action!:

if you wanted it adding to the code?

Definitely!

scalz

for unused pins, it should be floating, not pullup. set the pin register you need to 0x02.
Something like that
NRF_GPIO->PIN_CNF[ulPin] = 0x02;
that will put pin in same state like it's on reset. Everything disabled/default, floating, with disconnect bit set.
(see datasheet gpio).

@d00616 said in nRF5 Bluetooth action!:

Should I add a DISCONNECTED mode to hwPinMode()?

make sense to have it for input too.. i agree :simple_smile:

NeverDie

Maybe add:
OUTPUT_D0D1 -> Disconnected 0, Disconnected 1
or similar to your list as another easy way to effectuate the disconnect?

NeverDie

It finally makes sense now as to why there were all those "disconnected" choices among the various OUTPUT options. In my case, for controlling whether the solar panel is connected or disconnected, choosing OUTPUT_S0D1 works perfectly.

So, I suppose another way to disconnect an input pin would be to redefine it as an OUTPUT pin with a disconnect state, and then immediately put it into the disconnected state.

rmtucker

@d00616 said in nRF5 Bluetooth action!:

@rmtucker said in nRF5 Bluetooth action!:

Yes being able to change the prescaler dynamically would help a great deal as 125ms / 582.542 hours is not really useful for most applications with a 250ms overrun.

The sleep() function is now more precise for sleeping <512s:

https://github.com/mysensors/MySensors/pull/909

The PR is waiting for merge.

Hmm just tried the latest commit and it is giving me 306ms for sleep(10000).
Something not quite right.

NeverDie

@rmtucker
How are you measuring how long it's sleeping?

rmtucker

@NeverDie said in nRF5 Bluetooth action!:

@rmtucker
How are you measuring how long it's sleeping?

Just using hwMillis() before and after sleep and subtracting one from the other.
It was just reading + 250ms until @d00616 commited some changes a few hours ago.

rmtucker

something wrong in here:-

// Calculate sleep time and prescaler
		if (ms<512000) {
			// prescaler 0, 30.517 μs resolution -> max 512 s sleep
			MY_HW_RTC->PRESCALER =  0;
			// Set compare register to 1/30.517 µs to garantee event triggering
			// A minimum of 2 ticks must be guaranteed
			// (1000/32768)<<12 == 125
			MY_HW_RTC->CC[0] = max((ms<<12 / 125), 2);
		} else {
			// 8 Hz -> max 582.542 hours sleep.
			MY_HW_RTC->PRESCALER = 4095;
			// Set compare register to 1/125ms
			// A minimum of 2 ticks must be guaranteed
			MY_HW_RTC->CC[0] = max((ms / 125), 2);
		}

NeverDie

@rmtucker said in nRF5 Bluetooth action!:

@NeverDie said in nRF5 Bluetooth action!:

@rmtucker
How are you measuring how long it's sleeping?

Just using hwMillis() before and after sleep and subtracting one from the other.
It was just reading + 250ms until @d00616 commited some changes a few hours ago.

I thought so. The point being: doesn't millis stop when you're deep sleeping? Well, at least on an Arduino it does. Not sure what it does on the nRF5.

rmtucker

@NeverDie
No the nrf5 has a rtc.(Real time Counter)
It can even keep time while sleeping.(just found this out myself!).
That is a great leap forward on the arduino.

rmtucker

Try it just print the time out then put it to sleep for a minute then print the time out again.

rmtucker

The problem must be this line but i don't speak nrf5.

			// (1000/32768)<<12 == 125
			MY_HW_RTC->CC[0] = max((ms<<12 / 125), 2);```

rmtucker

The only other thing it could be is the deletion of this line in the commit.


nrf5_rtc_event_triggered = false

rmtucker

@d00616

MY_HW_RTC->CC[0] = max((ms<<12 / 125), 2);

Should be:-

MY_HW_RTC->CC[0] = max(((ms << 12) / 125), 2));

rmtucker

@d00616

Just checked and it now returns 10002 for a sleep(10000).
Much better after the above alteration.

NeverDie

Epilog: I made the changes so that just prior to taking a measurement the sense pin is hwPinMode'd to an input pin, and then immediately after the measurement I disconnect it. Seems to be working, and without the usurious power drain I was experiencing previously.

rmtucker

@NeverDie said in nRF5 Bluetooth action!:

Epilog: I made the changes so that just prior to taking a measurement the sense pin is hwPinMode'd to an input pin, and then immediately after the measurement I disconnect it. Seems to be working, and without the usurious power drain I was experiencing previously.

Good news
So what is the current usage now when sleeping?

NeverDie

@rmtucker said in nRF5 Bluetooth action!:

@NeverDie said in nRF5 Bluetooth action!:

Epilog: I made the changes so that just prior to taking a measurement the sense pin is hwPinMode'd to an input pin, and then immediately after the measurement I disconnect it. Seems to be working, and without the usurious power drain I was experiencing previously.

Good news
So what is the current usage now when sleeping?

About 6ua on this particular Ebyte nRF52832. I'm pretty sure it would be higher on my other Ebyte nRF52832, though I haven't measured it again. Haven't tested any additional ones as of yet.

mfalkvidd

@rmtucker very nice work, thanks for locating the problem.

It occurs because 12/125 will be evaluated before the bit shift. http://en.cppreference.com/w/c/language/operator_precedence for details.

d00616

@rmtucker said in nRF5 Bluetooth action!:

MY_HW_RTC->CC[0] = max((ms<<12 / 125), 2);
Should be:-
MY_HW_RTC->CC[0] = max(((ms << 12) / 125), 2));

Thank you. This was the result of merging some commits. I haven't seen I reversed that change. I had tested the code before merging some commits into one.

Actually I check the result of sleep(511999) and sleep(512001). When it's finished I fix that in MySensors.

d00616

@scalz said in nRF5 Bluetooth action!:

@d00616 said in nRF5 Bluetooth action!:

Should I add a DISCONNECTED mode to hwPinMode()?

make sense to have it for input too.. i agree

What's the best name for this mode? DISCONNECTED or INPUT_DISCONNECTED. I prefer the first variant.

I have to play a little bit with the port modes. Maybe it saves some current when the serial port pins are put into the disconnected mode while sleeping.

d00616

@d00616 said in nRF5 Bluetooth action!:

Actually I check the result of sleep(511999) and sleep(512001). When it's finished I fix that in MySensors.

Is fixed in development branch.
https://github.com/mysensors/MySensors/pull/917

scalz

@d00616 said in nRF5 Bluetooth action!:

@scalz said in nRF5 Bluetooth action!:

@d00616 said in nRF5 Bluetooth action!:

Should I add a DISCONNECTED mode to hwPinMode()?

make sense to have it for input too.. i agree

What's the best name for this mode? DISCONNECTED or INPUT_DISCONNECTED. I prefer the first variant.

I have to play a little bit with the port modes. Maybe it saves some current when the serial port pins are put into the disconnected mode while sleeping.

agree too for the first one should be enough :simple_smile:
yes, for lower power consumption, better disconnect pins which are not needed.
it's the same for a simple 328p though (setting the right pin states).

NeverDie

As a follow-up to rmtucker's line of inquiry, what is currently the shortest deep sleep that's supported? Is it one millisecond, or something else?

rmtucker

@NeverDie
Theoretically it is 2 clock ticks at 32768khz so 0.000061035secs i think.
But how long it takes to go into sleep mode and come out of sleep mode i am not sure.
But of course the sleep function only allows millis.

d00616

@NeverDie said in nRF5 Bluetooth action!:

As a follow-up to rmtucker's line of inquiry, what is currently the shortest deep sleep that's supported? Is it one millisecond, or something else?

Why do you need this type of short sleeps?

Sleep is for battery powered devices. A device that wakes up more than 1000 times in the second might be hard to drive with a battery.

@rmtucker said in nRF5 Bluetooth action!:

@NeverDie
Theoretically it is 2 clock ticks at 32768khz so 0.000061035secs i think.

This is correct.

But how long it takes to go into sleep mode and come out of sleep mode i am not sure.

It's simple to evaluate with micros() before and after a sleep().

NeverDie

I haven't yet upgraded to the current version, so maybe this is moot (?), but the following code in a loop:

  digitalWrite(TEST_PIN,HIGH);
  sleep(100); // Sleeps for 100ms
  digitalWrite(TEST_PIN,LOW);
  sleep(100); // Sleeps for 100ms

holds the TEST_PIN first HIGH for 250ms and then LOW for 250ms. That means 150ms of sleep overhead, which seems like a lot.

I measured the length of time the TEST_PIN is HIGH or LOW using an oscilloscope. Ran it on an Ebyte nRF52832.

NeverDie

Nevermind. I just now upgraded to the current versions, and it seems to be fixed.

NeverDie

So, with the current libraries and an Ebyte nRF52832 that's using its external crystal oscillator, I'm now measuring the sleep overhead as being 260us. I expect that may be even less if using the internal 32768Hz resonator.

NeverDie

I tried measuring the sleep overhead with the Ebyte nRF52832 running on its internal resonator, and surprisingly it wasn't that much faster: it appears to be about 220us.

Here's the test script:

#include <MySensors.h>

#define TEST_PIN 19  // (P0.19) 

void setup() 
{
  hwPinMode(TEST_PIN, OUTPUT_H0H1);  
  digitalWrite(TEST_PIN, LOW);  
}

void loop() {
  digitalWrite(TEST_PIN,HIGH);
  sleep(1); // Sleeps for 1ms
  digitalWrite(TEST_PIN,LOW);
  sleep(1); // Sleeps for 1ms  
}

Here's the scope capture:

Of course, this assumes (?) that the mcu sleeps for exactly 1ms, and during the extra 220us it is either ramping down or ramping up.

BTW, I don't anticipate sleeping for a mere 1ms at a time. However, to get a good measurement of the overhead using the oscilliscope I had to set the sleep period that low.

I can, however, well imagine having a use for sleep periods lasting 100ms.

NeverDie

Anyhow, it's not academic, as the plan is to approximate the "listen-mode" of an RFM69, but using the nRF52832. For that to be power efficient, I need the mcu to wake-up and fall-asleep very, very fast. For comparison, an atmega328p can wake-up in 3.8usec.

On page of the nRF52832 datasheet, it advertises:

Fast wake-up using 64 MHz internal oscillator

However, I'm not sure how to set that up. There's no menu check-box for that on the Arduino IDE tools menu like there is for the 32768Hz internal resonator. On the other hand, I'm not sure that it matters, because apparently the 64Mhz external crystal, which is what's slowing down the wake-up, is required to operate the radio.

NeverDie

Here's the current drain through a 1-ohm resistor:

i.e. 1mv=1ma.

As you can see, there's a rather long tail before it finally falls asleep.

Here is the same, but superimposed onto the TEST_PIN capture:

NeverDie

Good news. It appears that DCDC is already implemented on the Ebyte nRF52832 and working automatically!

Just for grins, I decided to measure the Tx time and current draw from sending a 13 byte payload in a packet, and I was happily surprised to see how low the current draw was:

The yellow trace marks the start and stop of the packet transmission process from a software point of view, but the blue trace measures the current (as before 1mv=1ma). As you can see, the transmission current never seems to rise above 2.5ma. The only (?) explanation I can think of is that DCDC must be working. Right? Tx power is set to be 4dbm.

It would be great if someone else would confirm/refute the measurement.

Nca78

@NeverDie said in nRF5 Bluetooth action!:

It would be great if someone else would confirm/refute the measurement.

I don't think it's possible, from the datasheet peak current is 7.7mA at +4dB with DCDC enabled with 3V power supply.
Current gain from 3V=>1.7V DCDC conversion is already included in this measurement so you should not be able to go lower.

How did you make your measurement across the resistor ?

NeverDie

@Nca78
You're right. It didn't ring true, so I setup some different capture hardware, and this time the image is a lot crisper:

This time I powered it from a 3.3v supercap and with the 1 ohm resistor soldered securely onto a PCB, with the o-scope leads on either side of it.

So, sadly, it doesn't look DCDC after all, because on this capture the peak is exceeding 20ma.

It's interesting how lengthy (and energy intensive) the phase is that's just prior to the transmission itself. I presume that's mainly just the PLL coming up to speed? It looks as though the actual current expended in the prelude exceeds that of the actual Tx proper!

I'm guessing that in the earlier scope capture, the probe must have slipped into 10x mode, because the shape is similar, just proportionately reduced by roughly that factor.

NeverDie

BTW, I assembled my third board now, and it sleeps at about 9.9ua. The first one sleeps at about 6ua, and the second at about 9ua. It would be interesting to know why the first board is so much less, but it seems that about 9-10ua is the more typical number. That also seems to agree with @d00616 's measurements.

NeverDie

Interestingly enough, you can put the radio into receive mode and then sleep the mcu with the radio still in receive mode. Here's a screenshot of current consumption while receiving, where I alternate between leaving the mcu active or sleeping it (each for duration of 500ms). In-between, I sleep everything (both radio and mcu) for 1 second:

NeverDie

Here's the mode that I'm most interested in: Putting the radio into Rx for about 1ms per 100ms interval to listen for remote commands. The rest of the time everthing (both radio and mcu) are in deep sleep waiting for the RTC to wake them up.

Here's a close-up of the current drawn during that roughly 1ms interval:

I ran this just now, and my solar setup can easily handle this load during the daytime, even from deep indoors far from the windows. This was the scenario that really stressed the RFM69+atmega328p combo when I tried doing it using the RFM69's listen mode. I'll see tonight how the 10F supercap handles the load without any solar assist.

Because of the nRF52839's 2Mbps datarate, I can probably cut the listen window down substantially from 1ms to much less (much less than would be possible with an RFM69, due to its maximum of 300kbps datarate), but for ease of programming I'm starting with this.

d00616

@NeverDie said in nRF5 Bluetooth action!:

Here's the mode that I'm most interested in: Putting the radio into Rx for about 1ms per 100ms interval to listen for remote commands. The rest of the time everthing (both radio and mcu) are in deep sleep waiting for the RTC to wake them up.

When you take a look into the PPI section, you are able to let the CPU sleep until a radio packet is received. With PPI, the listen mode can be activated and deactivated without CPU interaction.

The nRF5 MCUs are able to to a lot of things without waking up the CPU. That's a really cool feature.

NeverDie

@d00616 said in nRF5 Bluetooth action!:

@NeverDie said in nRF5 Bluetooth action!:

Here's the mode that I'm most interested in: Putting the radio into Rx for about 1ms per 100ms interval to listen for remote commands. The rest of the time everthing (both radio and mcu) are in deep sleep waiting for the RTC to wake them up.

When you take a look into the PPI section, you are able to let the CPU sleep until a radio packet is received. With PPI, the listen mode can be activated and deactivated without CPU interaction.

The nRF5 MCUs are able to to a lot of things without waking up the CPU. That's a really cool feature.

Sounds like it has potential. Any demo code for this? The datasheet seems a bit sketchy.

d00616

@NeverDie said in nRF5 Bluetooth action!:

@d00616 said in nRF5 Bluetooth action!:

@NeverDie said in nRF5 Bluetooth action!:

Here's the mode that I'm most interested in: Putting the radio into Rx for about 1ms per 100ms interval to listen for remote commands. The rest of the time everthing (both radio and mcu) are in deep sleep waiting for the RTC to wake them up.

When you take a look into the PPI section, you are able to let the CPU sleep until a radio packet is received. With PPI, the listen mode can be activated and deactivated without CPU interaction.
The nRF5 MCUs are able to to a lot of things without waking up the CPU. That's a really cool feature.

Sounds like it has potential. Any demo code for this? The datasheet seems a bit sketchy.

These are some snippets of the radio code. There are fully useable PPI and some predefined. For fully useable PPI into the EEP register, you put the address of an EVENT register and in the TEP register, you put the pointer to an TASK register.

   /** Configure PPI (Programmable peripheral interconnect) */
    // Start timer on END event
    NRF_PPI->CH[NRF5_ESB_PPI_TIMER_START].EEP = (uint32_t)&NRF_RADIO->EVENTS_END;
    NRF_PPI->CH[NRF5_ESB_PPI_TIMER_START].TEP = (uint32_t)&NRF5_RADIO_TIMER->TASKS_START;
    // Disable Radio after CC[0]
    NRF_PPI->CH[NRF5_ESB_PPI_TIMER_RADIO_DISABLE].EEP = (uint32_t)&NRF5_RADIO_TIMER->EVENTS_COMPARE[0];
    NRF_PPI->CH[NRF5_ESB_PPI_TIMER_RADIO_DISABLE].TEP = (uint32_t)&NRF_RADIO->TASKS_DISABLE;
    ...
    // Set PPI
     NRF_PPI->CHENSET = NRF5_ESB_PPI_BITS;
    ...
  // Clear PPI
    NRF_PPI->CHENCLR = NRF5_ESB_PPI_BITS;

Then you have to enable or disable the register. It could be necessary to reset the events. You can use the NRF_RESET_EVENT macro to do this job.

 NRF_RESET_EVENT(NRF5_RADIO_TIMER->EVENTS_COMPARE[0]);

NeverDie

I have a brute force version of "listen mode" working using just the libraries, but I have to re-initialize the radio after each cycle because it appears to lose its settings every time I sleep it.

Anyway, finding a way to add DCDC mode to these modules will probably have the biggest near-term impact on current consumption. That said, I'm sure plenty of energy savings can also be found by honing the code.

NeverDie

Actually, even just sleeping the MCU with a simple command like:

sleep(100);

is apparently enough to require a re-init of the radio afterward. Not sure why that would be.

NeverDie

Comparing Figures 169 and 170 in the nRF52832 datasheet, it looks as though simply adding two inductors in series between DCC and DEC4 should be all that's needed to provide the needed hardware support for DC/DC. Looks as though the 10uH inductor also needs to be able to support a minimum of 50ma, according to the BOM (Table 145).

So, is it as simple as that together with enabling register DCDCEN? Or, is there anything more to it?

scalz

Yes. This is like that. I use 2 inductors (better) in serie. Why more complicated

d00616

@NeverDie said in nRF5 Bluetooth action!:

Actually, even just sleeping the MCU with a simple command like:
sleep(100);

is apparently enough to require a re-init of the radio afterward. Not sure why that would be.

sleep() deinitializes the transport with transportDisable(). This results in power down the radio.

At the moment I review the ESB code. I think the nRF5 is 12-13µs after an nRF24 in RX mode and 432µs before an nRF24 in TX. This can result in unstable connections when debug messages are disabled.

NeverDie

Sort-of working. Here's a screen shot with the DC/DC modification. Compare to the earlier one above:

Probably non-optimal placement of the inductors: between the DCC and DEC4 pins on my breakout board for the nRF52832.

This is reason enough to do an new version of the breakout for the Ebyte module to improve the inductor positioning.

Here's the enable code:

  NRF_POWER->DCDCEN=1;  //enable the DCDC voltage regulator as the default.

If it's this easy, I'm just surprised that the module makers haven't included it. The difference in build cost is de minimus, but the difference in delivered value is huge.

Also, it sounds like I'll have to write a variant of sleep that sleeps just the MPU while leaving the radio in receive mode. That's an easy win to improve the current consumption.

NeverDie

Good news! I went back and re-rechecked using an un-modified Ebyte module, and, indeed, this time I'm sure that the DCDC inductors are already on it! What follows is the proof. Here is the current drawn when the above DCDCEN is enabled on an unmodified Ebyte module:

~~Now, here is the current drawn with the exact same script on the exact same unmodified Ebyte module, but with the DCDCEN line of code commented out:~~

QED.

~~As you can see, the savings in current consumption are considerable with the DCDC enabled!~~

~~[Edit: although looking at it again, the timescale seems way off. Argh. Something still isn't right.]~~

NeverDie

Scratch the preceeding post. I redid it more carefully this time, and I believe it confirms that the Ebyte module does not have the two inductors required for DC/DC mode.

Here is the current drawn by an unmodified Ebyte nRF52832 module which is programmed to be receiving for about 1.5ms every 100ms:

NeverDie

Here is what happens with exactly the same hardware (no inductors yet added), but with DCDCEN enabled:

It basically seems caught in a boot loop.

NeverDie

Now, adding the two inductors between DCC and DEC4, and re-measuring, we get:

No less importantly, it does receive and decode packets!

Conclusion: Ebyte nRF52832 modules don't come with the DC/DC inductors already installed. However, they can be added, resulting in some current reduction.

NeverDie

I've baked these findings into a new breakout board for the Ebyte nRF52832:
https://www.openhardware.io/view/471
The new breakout board will enable the module to work in DC/DC mode.

NeverDie

I may have found a clue as to why the reset pin (pin0.21) on the nRF52832 isn't working.

On the nRF52832 DK, I read the following register values:
PSELRESET[0]=21
PSELRESET[1]=21

which is as expected. However, on the Ebyte nRF52832 module, I read those register values as:
PSELRESET[0]=4294967295
PSELRESET[1]=4294967295

which makes no sense. The values match, but they don't correspond to a pin number that can represent RESET.

These two registers are described in the nRF52832 datasheet.

mfalkvidd

@NeverDie not sure if you've already noticed, but 4294967295 is the maximum value for an unsigned 32-bit integer. So the value is 0xFFFFFFFF. That often means uninitialized. I don't know why it would be uninitialized though.

NeverDie

@mfalkvidd

Maybe because they just never were?
Those particular registers are "The user information configuration registers (UICRs) are non-volatile memory (NVM) registers for configuring user specific settings." So, it would seem that initializing them just once would be enough, since they're non-volatile.

In any case, good catch! It explains both why they are that value and also why they match.

NeverDie

@NeverDie said in nRF5 Bluetooth action!:

4294967295

Also, since 4294967295 equals 0xFFFFFFFF, then bit 31 is a '1', which, according to the datasheet, means the pin is disconnected (see section 14.1.60 PSELRESET[0] of the datasheet for the detail].

NeverDie

@mfalkvidd said in nRF5 Bluetooth action!:

So the value is 0xFFFFFFFF. That often means uninitialized. I don't know why it would be uninitialized though.

There's a chance we may have unwittingly done it ourselves! Remember back to when we were doing an explicit "Erase All"? From the datasheet:

11.5 Erase all
When erase is enabled, the whole Flash and UICR can be erased in one operation by using the ERASEALL
register.

Furthermore, from page 29 of the datasheet:

After erasing UICR all bits in UICR are set to '1'.

d00616

@NeverDie said in nRF5 Bluetooth action!:

@mfalkvidd said in nRF5 Bluetooth action!:

So the value is 0xFFFFFFFF. That often means uninitialized. I don't know why it would be uninitialized though.

There's a chance we may have unwittingly done it ourselves! Remember back to when we were doing an explicit "Erase All"? From the datasheet:

This is part of the arduino-nrf5 code -> https://github.com/sandeepmistry/arduino-nRF5/blob/dc53980c8bac27898fca90d8ecb268e11111edc1/cores/nRF5/SDK/components/toolchain/system_nrf52.c#L156

I don't have any idea why this is not included in the binary. When the reset menu is selected then "-DCONFIG_GPIO_AS_PINRESET" is given to gcc.

When system_nrf52.c is completely ignored, then the erratas are not handled.

NeverDie

Here is some verbose code which properly sets the registers to use pin P0.21 as the RESET pin:

Serial.println("Testing...");
delay(10000);  //give preparation time to open serial tty
Serial.print(counter);
Serial.print(", PSELRESET[0]=");
Serial.println(NRF_UICR-> PSELRESET[0]);
Serial.print(counter++);
Serial.print(", PSELRESET[1]=");
Serial.println(NRF_UICR-> PSELRESET[1]);

Serial.println();
Serial.println("Write-enabling CONFIG.");
NRF_NVMC->CONFIG=1;  // Write enable the UICR

Serial.println();
Serial.println("Now designating pin pO.21 as the RESET pin.");
NRF_UICR-> PSELRESET[0]=21;  //designate pin pO.21 as the RESET pin
NRF_UICR-> PSELRESET[1]=21;  //designate pin pO.21 as the RESET pin

Serial.println();
Serial.println("Confirming that RESET pin assigment took hold:");
Serial.print(counter);
Serial.print(", PSELRESET[0]=");
Serial.println(NRF_UICR-> PSELRESET[0]);
Serial.print(counter++);
Serial.print(", PSELRESET[1]=");
Serial.println(NRF_UICR-> PSELRESET[1]);

Serial.println();
Serial.println("Return CONFIG to read-only mode.");
NRF_NVMC->CONFIG=0;  // Put the UICR back into read-only mode.

Running it once seems to be good enough, unless there were to occur another "Erase All" or "Burn bootloader" event.

Here is the output from running the code which shows that it succeeded:

Testing...
0, PSELRESET[0]=4294967295
0, PSELRESET[1]=4294967295

Write-enabling CONFIG.

Now designating pin pO.21 as the RESET pin.

Confirming that RESET pin assigment took hold:
1, PSELRESET[0]=21
1, PSELRESET[1]=21

Return CONFIG to read-only mode.

NeverDie

Until a more elegant solution can be found, I'm using this in the setup() routine as the workaround:

  if (((NRF_UICR-> PSELRESET[0])==0xFFFFFFFF) && ((NRF_UICR-> PSELRESET[1])==0xFFFFFFFF)) { //if the two RESET registers are erased
    NRF_NVMC->CONFIG=1;  // Write enable the UICR
    NRF_UICR-> PSELRESET[0]=21;  //designate pin P0.21 as the RESET pin
    NRF_UICR-> PSELRESET[1]=21;  //designate pin P0.21 as the RESET pin
    NRF_NVMC->CONFIG=0;  // Put the UICR back into read-only mode.
  }

The code has the positive virtue of not writing to the RESET rregisters unless both registers are erased. That helps ensure that the non-volatile memory does not get worn out prematurely.

NeverDie

@NeverDie said in nRF5 Bluetooth action!:

Until a more elegant solution can be found, I'm using this in the setup() routine as the workaround:
  if (((NRF_UICR-> PSELRESET[0])==0xFFFFFFFF) && ((NRF_UICR-> PSELRESET[1])==0xFFFFFFFF)) { //if the two RESET registers are erased
    NRF_NVMC->CONFIG=1;  // Write enable the UICR
    NRF_UICR-> PSELRESET[0]=21;  //designate pin P0.21 as the RESET pin
    NRF_UICR-> PSELRESET[1]=21;  //designate pin P0.21 as the RESET pin
    NRF_NVMC->CONFIG=0;  // Put the UICR back into read-only mode.
  }
The code has the positive virtue of not writing to the RESET rregisters unless both registers are erased. That helps ensure that the non-volatile memory does not get worn out prematurely.

Good news! I've confirmed that doing this does indeed solve the problem I previously had with the EByte nRF52832 module not reacting to a reset on pin P0.21. After inserting the above code block into the nRF52832's setup() routine, I can now, using ESP-LINK, remotely reset an nRF52832 module:
https://www.openhardware.io/view/443/nRF52832-ESP-LINK-Shield-for-ESP8266-Wemos-D1-Mini

NeverDie

With that issue now settled, I'm moving on to a different topic: what happens if you put the radio into Tx mode, but with an empty buffer (i.e. nothing to send)? In this scenario an RFM69 transmits a continuous pre-amble, and I'm wondering whether the nRF52832 does the same?
With an empty buffer, does it transmit anything at all? Anyone happen to know?

The reason I ask is that I want to program the radio to send a continuous signal so as to quickly wake-up a receiver. With packets, there's the lag time of receiving and decoding the packet, rather than just reacting to a high RSSI. In this way, I can use much narrower listen windows and thereby save a lot of current consumption.

nRF5 action!

Suggested Topics

Welcome
Announcements • • hek

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

HVAC Controller
My Project • • Michael Link

Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

A low cost energy meter
My Project • • OldSurferDude

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts

nRF5 action!

Suggested Topics

Welcome Announcements • • hek

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway My Project • • fsgraz

HVAC Controller My Project • • Michael Link

Water Filtering and Sterilization and Hot Water Recirculation My Project • • fsgraz

A low cost energy meter My Project • • OldSurferDude

Controlling Blinds.com RF Dooya Motors with Arduino and Vera My Project • • petewill

0Online

11.4kUsers

11.1kTopics

112.7kPosts

Welcome
Announcements • • hek

Alexa Fauxmo - Mysensor Bridge Gateway / BLE - Mysensors Bridge Gateway
My Project • • fsgraz

HVAC Controller
My Project • • Michael Link

Water Filtering and Sterilization and Hot Water Recirculation
My Project • • fsgraz

A low cost energy meter
My Project • • OldSurferDude

Controlling Blinds.com RF Dooya Motors with Arduino and Vera
My Project • • petewill

0
Online

11.4k
Users

11.1k
Topics

112.7k
Posts