💬 NRF2RFM69

gohan

So why isn't it working then? Did I fry the radio?

tbowmo

Could you have added it to a 5V arduino? RFM is not 5V tolerant, so that could fry the radio..

gohan

No, I used it only on the raspberry

gohan

New update: I used the module on the EasyPCB, nrf24 version, from @sundberg84 and recompiled the sketch to use the rfm69 and it is able to initialize the radio. So there must be something wrong with the compiled gateway on the RPI as it should be a direct swap from a NRF24. I am moving to the RPI thread

PS Now it seems to be working... I haven't changed anything.... must have been a bad connection then

mysgw: MCO:BGN:INIT CP=RPNG----
mysgw: TSF:LRT:OK
mysgw: TSM:INIT
mysgw: TSF:WUR:MS=0
mysgw: TSM:INIT:TSP OK
mysgw: TSM:INIT:GW MODE
mysgw: TSM:READY:ID=0,PAR=0,DIS=0
mysgw: MCO:REG:NOT NEEDED
mysgw: Listening for connections on 0.0.0.0:5003
mysgw: MCO:BGN:STP
mysgw: MCO:BGN:INIT OK,TSP=1

Markus.

Hi all,
which size of cap should be used on this board and is it possible to connect a SMA Antenna ?

Many thanks

Markus

tbowmo

use a 4.7uF capacitor, or there about..

There is no pads for a SMA connector, but you could attach one with a pigtail..

Markus.

@tbowmo Thanks for the Information... One stupid question about the SMA conenctor :-) Is it enough to connect only the Antenna Output conenction or must GND also conencted...?

gohan

You can just solder the antenna only on pcb. I use a coil spring type

Markus.

just one more question... I have on the Gateway a RFM69HW and a node with a RFM69W module. In the Gateway Sketch is the HW type enabled

#define MY_RFM69_FREQUENCY RF69_868MHZ
#define MY_IS_RFM69HW

But there is no comunication from the node... I use Mysensors 2.1.1.
Any idea?

gohan

What gateway is that? I'd suggest to try mysensors 2.2 development

Markus.

@gohan It at the Moment only a test. So I have one EasyPCB NRF board with FTDI as Gateway and another EasyPCB board with DHT22 Sensor attached as Node. On both is a 4,7uF electrolytic condensator attached Close to the NRF socket. Both boards are at the Moment with RFM69W 868. The sensor node is battey powered.

gohan

Get latest 2.2 library and use new rfm69 driver. Did you remember to close the IRQ contact in the easypcb?

Markus.

@gohan Oh Sh* must check this... I've tried it yesterday on both devices the 2.2 Dev. But will Keep ypu informed...
Don't find the jumperfor the IRQ on the Rev 9 board. can you please post a Picture. Seems that this one is definitly not closed...
--> Edit... found it in the documentation but still the same.
Think the next Point to check for me are the antennas... :-(

gohan

I'd suggest to buy the coil spring antennas for your frequency, they are cheap and compact.

Markus.

in principle there is traffic between node and Gateway..

159631 !TSM:FPAR:NO REPLY
159637 TSM:FPAR
169848 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
171868 !TSM:FPAR:NO REPLY
171874 TSM:FPAR
179087 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
181106 !TSM:FPAR:FAIL
181112 TSM:FAIL:CNT=4
181118 TSM:FAIL:DIS
181123 TSF:TDI:TSL
191131 TSM:FAIL:RE-INIT
191137 TSM:INIT
191143 TSM:INIT:TSP OK
191150 TSM:INIT:STATID=10
191158 TSF:SID:OK,ID=10
191164 TSM:FPAR
198377 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
200396 !TSM:FPAR:NO REPLY
200402 TSM:FPAR
207616 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
209635 !TSM:FPAR:NO REPLY
209641 TSM:FPAR
216854 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
218873 !TSM:FPAR:NO REPLY
218880 TSM:FPAR
226093 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
228112 !TSM:FPAR:FAIL
228118 TSM:FAIL:CNT=5
228124 TSM:FAIL:DIS
228128 TSF:TDI:TSL
238135 TSM:FAIL:RE-INIT
238141 TSM:INIT
238147 TSM:INIT:TSP OK
238153 TSM:INIT:STATID=10
238161 TSF:SID:OK,ID=10
238168 TSM:FPAR
248385 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
250404 !TSM:FPAR:NO REPLY
250411 TSM:FPAR
257624 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
259643 !TSM:FPAR:NO REPLY
259649 TSM:FPAR
269731 TSF:MSG:SEND,10-10-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
271751 !TSM:FPAR:NO REPLY
271757 TSM:FPAR

0;255;3;0;9;189196 TSF:PNG:SEND,TO=0
0;255;3;0;9;189206 TSF:CKU:OK
0;255;3;0;9;189214 TSF:MSG:GWL OK
0;255;3;0;9;191236 !TSF:MSG:SEND,0-0-10-10,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0
0;255;3;0;9;244555 TSF:MSG:READ,10-10-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;244574 TSF:MSG:BC
0;255;3;0;9;244582 TSF:MSG:FPAR REQ,ID=10
0;255;3;0;9;244594 TSF:PNG:SEND,TO=0
0;255;3;0;9;244604 TSF:CKU:OK
0;255;3;0;9;244613 TSF:MSG:GWL OK
0;255;3;0;9;257744 !TSF:MSG:SEND,0-0-10-10,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0
0;255;3;0;9;269957 TSF:MSG:READ,10-10-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;269977 TSF:MSG:BC
0;255;3;0;9;269985 TSF:MSG:FPAR REQ,ID=10
0;255;3;0;9;269996 TSF:PNG:SEND,TO=0
0;255;3;0;9;270006 TSF:CKU:OK
0;255;3;0;9;270014 TSF:MSG:GWL OK
0;255;3;0;9;281585 !TSF:MSG:SEND,0-0-10-10,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0
0;255;3;0;9;289732 TSF:MSG:READ,10-10-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;289753 TSF:MSG:BC
0;255;3;0;9;289761 TSF:MSG:FPAR REQ,ID=10
0;255;3;0;9;289771 TSF:PNG:SEND,TO=0
0;255;3;0;9;289781 TSF:CKU:OK
0;255;3;0;9;289789 TSF:MSG:GWL OK
0;255;3;0;9;297015 !TSF:MSG:SEND,0-0-10-10,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0
0;255;3;0;9;306757 TSF:MSG:READ,10-10-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;306776 TSF:MSG:BC
0;255;3;0;9;306784 TSF:MSG:FPAR REQ,ID=10
0;255;3;0;9;306796 TSF:PNG:SEND,TO=0
0;255;3;0;9;306806 TSF:CKU:OK
0;255;3;0;9;306814 TSF:MSG:GWL OK
0;255;3;0;9;316682 !TSF:MSG:SEND,0-0-10-10,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0
0;255;3;0;9;322084 TSF:MSG:READ,10-10-255,s=255,c=3,t=7,pt=0,l=0,sg=0:
0;255;3;0;9;322103 TSF:MSG:BC
0;255;3;0;9;322111 TSF:MSG:FPAR REQ,ID=10
0;255;3;0;9;322123 TSF:PNG:SEND,TO=0
0;255;3;0;9;322131 TSF:CKU:OK
0;255;3;0;9;322142 TSF:MSG:GWL OK
0;255;3;0;9;333180 !TSF:MSG:SEND,0-0-10-10,s=255,c=3,t=8,pt=1,l=1,sg=0,ft=0,st=NACK:0

gohan

That's either the node not receiving or the gateway having problems when sending

Markus.

@gohan :-( any idea what else I can do/check ?

alexsh1

@Markus. You have an RF issue. Typically for nrf24l01+ I'd use a different power supply or a different module.

Are you sure both modules are set to the same channel and frequency? What antennas are you using?
Do you have HW modules?

Markus.

@alexsh1 I use at the Moment RFm69W 868 modules not NRF. Because the RFMs are mounted on the NRF connector on an EasyPCB. I use at the Moment single wire antennas with a lenght of 8,3 cm.

alexsh1

@Markus and channel and freq? are they the same in your sketch?

💬 NRF2RFM69

16

11.7k

11.2k

113.1k