💬 Building a wired RS485 sensor network

kimot

Some works for MySensors done:
https://forum.mysensors.org/topic/3977/transport-based-on-single-wire-pjon-protocol

kimot

But PJON uses completely sw bit by bit sending or HW sending with bad bus arbitration.

My idea - combination CAN bus like arbitration and UART message sending.
With ACK possibility.

Time T1 ( two bytes send time for example )

Node sends message and waits T1 time for ACK.
Receiving node must send ACK within T1 interval.

Node, witch needs send message listens bus.
BUT not by HW UART or SoftwareSerial - use directo IO operation.
If recognize bus free time greater then T1, it start sending its own ID.
BUT again not by HW UART or SoftwareSerial - but bit by bit by direct IO pin operation.
And listen if bit I am sending is bit I am receiving.
If not - it means, that other node with higher priority ( lower ID ) is sending - then immediately stop sending other bit and wait for next bus free T1 interval.
If yes - bus is free for me end send my message normally by UART ( HW or SW, maybe with 9 bit addressing support - time less than T1 between characters allowed).
Wait max T1 time for ACK.

CAN bus driver usage TJA 1050 or MCP2551 - no DE RE pins.

Andreas Sieber

I have the problem that I always get this error: !TSM:FPAR:NO REPLY

Once it worked briefly yesterday.

What have I tried everything?
All hardware exchanged - without success.

Now I have just written two small scripts that send RS485 back and forth. without problems. So wiring has to fit. I spent then in the serial montior the data which the node sends me, there comes some. Then I once tried to display the data that sends the GW, because nothing comes.

Does anyone have an idea why my GW does not answer?

mfalkvidd

@andreas-sieber could you post the debug output from the node and the gateway?

Andreas Sieber

| / |_ / | ___ _ __ ___ ___ _ __ ___
| |/| | | | _ \ / _ \ _ \/ __|/ _ \| _/ __|
| | | | || || | / | | _ \ _ | | _
|| ||_, |/ ___|| ||/_/|| |/
|__/ 2.3.0-alpha

17 MCO:BGN:INIT NODE,CP=RSNNA---,VER=2.3.0-alpha
26 TSM:INIT
27 TSF:WUR:MS=0
29 TSM:INIT:TSP OK
30 TSM:FPAR
49 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2056 !TSM:FPAR:NO REPLY
2058 TSM:FPAR
2075 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4083 !TSM:FPAR:NO REPLY
4085 TSM:FPAR
4103 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6111 !TSM:FPAR:NO REPLY
6113 TSM:FPAR
6130 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:

0;255;3;0;9;0 MCO:BG
0;255;3;0;9;29 MCO:BGN:INIT OK,TSP=1
0;255;3;0;9;0 MCO:BGN:INIT GW,CP=RSNGA---,VER=2.3.0-alpha
0;255;3;0;9;5 TSM:INIT
0;255;3;0;9;7 TSF:WUR:MS=0
0;255;3;0;9;9 TSM:INIT:TSP OK
0;255;3;0;9;12 TSM:INIT:GW MODE
0;255;3;0;9;15 TSM:READY:ID=0,PAR=0,DIS=0
0;255;3;0;9;18 MCO:REG:NOT NEEDED
0;255;3;0;14;Gateway startup complete.
0;255;0;0;18;2.3.0-alpha
0;255;3;0;9;22 MCO:BGN:STP
0;255;3;0;9;29 MCO:BGN:INIT OK,TSP=1

gohan

why don't you use the stable 2.2? Anyway the node is missing the my_node_id define and second it seems the gateway isn't receiving anything, so I guess there is something very wrong in communication

Andreas Sieber

in the 2.2 the same problem, i have now updagradet to alpha.

When you have a solution on 2.2 i will downgrade. no problem!

Guys you are good! I had set the mynodeid. But befor i include the my sensors.. that's the mistake..

hour of hour to search... thx!

Omemanti

Is it possible, or will it be possible to build a combination between wired and wireless nodes?

gohan

one network, one gateway

Pavel Polititsky

I just trying to work with examples but my node always transmitting some piece of shit from hardware serial:

 
 __  __       ____
|  \/  |_   _/ ___|  ___ _ __  ___  ___  _ __ ___
| |\/| | | | \___ \ / _ \ `_ \/ __|/ _ \| `__/ __|
| |  | | |_| |___| |  __/ | | \__ \  _  | |  \__ \
|_|  |_|\__, |____/ \___|_| |_|___/\___/|_|  |___/
        |___/                      2.3.0

16 MCO:BGN:INIT NODE,CP=RSNNA---,VER=2.3.0
25 TSM:INIT
26 TSF:WUR:MS=0
28 TSM:INIT:TSP OK
29 TSF:SID:OK,ID=5
31 TSM:FPAR
⸮X⸮⸮w34 TSF:MSG:SEND,5-5-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2041 !TSM:FPAR:NO REPLY
2043 TSM:FPAR
⸮X⸮⸮w2045 TSF:MSG:SEND,5-5-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4054 !TSM:FPAR:NO REPLY
4056 TSM:FPAR
⸮X⸮⸮w4058 TSF:MSG:SEND,5-5-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6066 !TSM:FPAR:NO REPLY
6068 TSM:FPAR
⸮X⸮⸮w6070 TSF:MSG:SEND,5-5-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8078 !TSM:FPAR:FAIL
8079 TSM:FAIL:CNT=1
8081 TSM:FAIL:DIS
8083 TSF:TDI:TSL

From software serial too

⸮X⸮⸮w
⸮X⸮⸮w
⸮X⸮⸮w
⸮X⸮⸮w

Consequently the gateway can't find any device.
I have tried also with RS485 with different baudrate. Finally I just connect my USB TTL directly to ouput pins, but always same result.
How to fix it?

rejoe2

@Pavel-Polititsky
To me this looks like you mixed between-node communication (RS485) with debug output (and maybe also serial output of the gw).
The corresponding serial interface for RS485 should be dedicated to RS485 exclusively.

PepoV6

Hi,
first of I have to thank you for your effort on this project! It helped me a lot.
In my house I would like to build 2 networks, one with serial gateway with RF24 for ground floor and outside. Second will be in cellar and I was thinking about Ethernet gateway (W5500) but sensors will be connected via RS485. Do you have code for that? On the video it looks like that in the box on right side it is something like this.

GieBek

I have exactly the same problem. Has anyone managed to run it.

GieBek

| / |_ / | ___ _ __ ___ ___ _ __ ___
| |/| | | | _ \ / _ \ _ \/ __|/ _ \| _/ __|
| | | | || || | / | | _ \ _ | | _
|| ||_, |/ ___|| ||/_/|| |/
|__/ 2.3.1

16 MCO:BGN:INIT NODE,CP=RSNNA---,REL=255,VER=2.3.1
26 TSM:INIT
27 TSF:WUR:MS=0
28 TSM:INIT:TSP OK
30 TSM:FPAR
56 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
2063 !TSM:FPAR:NO REPLY
2065 TSM:FPAR
2082 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
4090 !TSM:FPAR:NO REPLY
4092 TSM:FPAR
4110 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
6118 !TSM:FPAR:NO REPLY
6120 TSM:FPAR
6137 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
8146 !TSM:FPAR:FAIL
8147 TSM:FAIL:CNT=1
8150 TSM:FAIL:DIS
8152 TSF:TDI:TSL
18154 TSM:FAIL:RE-INIT
18156 TSM:INIT
18157 TSM:INIT:TSP OK
18159 TSM:FPAR
18178 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
20186 !TSM:FPAR:NO REPLY
20188 TSM:FPAR
20206 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
22213 !TSM:FPAR:NO REPLY
22215 TSM:FPAR
22234 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
24241 !TSM:FPAR:NO REPLY
24243 TSM:FPAR
24261 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:
26268 !TSM:FPAR:FAIL
26269 TSM:FAIL:CNT=2
26271 TSM:FAIL:DIS
26273 TSF:TDI:TSL

mfalkvidd

@giebek could you describe the problem, what your setup looks like, and what you have tried so far to troubleshoot it? There are 137 posts in this thread so it is a bit hard to figure out which problem you are referring to.

rejoe2

@GieBek

6137 TSF:MSG:SEND,255-255-255-255,s=255,c=3,t=7,pt=0,l=0,sg=0,ft=0,st=OK:

Imo this indicates your node doesn't have a NodeID yet. When using RS485 you have to assign the ID's manually in the sketch, auto doesn't work... (e.g. #define MY_NODE_ID 123)

GieBek

Thanks for the answers.
And even more thanks to the rejoe2

#define MY_NODE_ID 123

it helped 100% the transmission went, domoticz sees children.

dzjr

hello MySensors friends,

I am currently making a node based on an arduino Mega 2560 with transport via RS-485, the build page says that we should use the MEGA pin 46 & 48, I was wondering if I would like a reference for this. in the sketch.
Second question; can I use pin 47 for the DE pin with:

#define MY_RS485_DE_PIN 47

I haven't tested anything yet, so actually I just ask a lazy question ;)

APL2017

Hello, I would like to better understand the concept here. It sounds like we still need a gateway connected to a controller (serial, Ethernet, WiFi, etc.) but the interface between gateway and multiple nodes is over wired RS485 serial interface. Please confirm. Thank you for your great efforts!

rejoe2

@apl2017 Yes, also for RS485 variant you'll need a gateway. Only the communication between the gateway and the other nodes is handled over RS485, connected to a second (typically software) serial interface (for remote nodes, you may just use the hardware serial interface to connect the RS485 transceiver, if you do not need debug output; but imo this option is not recommended for beginners).

💬 Building a wired RS485 sensor network

26

11.7k

11.2k

113.1k