Your browser does not seem to support JavaScript. As a result, your viewing experience will be diminished, and you may not be able to execute some actions.

Please download a browser that supports JavaScript, or enable it if it's disabled (i.e. NoScript).

💬 LCDUINO

openhardware.io last edited by

https://www.openhardware.io/view/8247/LCDUINO
Reply Quote 0
1 Reply Last reply
mfalkvidd Mod last edited by

( Verifying that posting to this thread works. Please ignore. )
Reply Quote 0
1 Reply Last reply
NeverDie Hero Member last edited by

Testing using Firefox browser.
Reply Quote 1
1 Reply Last reply
NeverDie Hero Member last edited by

This project is missing a bill of materials. In particular, the LCD components don't appear to be named, not even on the schematic.

Also, do there exist gerber files to accompany it?
Reply Quote 0
1 Reply Last reply
Nca78 Hardware Contributor last edited by @NeverDie

@NeverDie said in LCDUINO:

the LCD components don't appear to be named, not even on the schematic

Looks like a typical text LCD like 1602 on the picture.
Reply Quote 1
1 Reply Last reply

serial 20 arduino nano 13 lcd 5 uart 4

5
Posts

74
Views

Log in to reply

Suggested Topics

Gateway not working on VeraLite + UI6 - No Serial Port configuration available
Vera • vera serial serialgateway ui6 • • cdrum

11

0
Votes

11
Posts

5980
Views

@brettzky84 said: Im using the serial gateway on u17 and have it working fine. i have the same problem as you when my vera is rebooted or powered off, but found 2 solutions. 1 with the vera on disconnect then reconnect the serial gateway. wait 10seconds refresh the dashboard page. Then go to app/ developer apps/ serial connection. Reset your baud rate to 115200??... Thansk. I ended up upgrading to the latst UI7 beta. My gateway is now working!!! Let's see how stable it is. (UI7 has fixed some of my other issue too)
Stabile Controller
Troubleshooting • mqtt openhab serial • • C.r.a.z.y.

9

0
Votes

9
Posts

3652
Views

@celonunes generally raspberry pi with serial usb but also you can see some mqtt logs. Same problem with mac os with serial usb. I also tried rpi uart pins for serial bu there is no logs for it. Maybe someone gives his Openhab dir i can understand better problem isnt related with hardware
Communication problems between MQTT Gateway (OrangePi) and Node (Arduino Nano)
Troubleshooting • gateway mqtt nrf24 arduino nano communication problems orangepi • • gammlerstyle

7

1
Votes

7
Posts

757
Views

Hi, for everyone who reads all of this, forget about the last few posts. I don't know why it works even when the Interrups are masked out on the radio, but it works now. The error I had occured because of the config of the OrangePi-Gateway. I removed: --extra-cxxflags="-DMY_RF24_DATARATE=\(RF24_250KBPS\) -DMY_RF24_BASE_RADIO_ID=\(0x00,0xFC,0xE1,0xA8,0xA8\) -DMY_DEBUG_VERBOSE_RF24" and wrote: --extra-cxxflags="-DMY_RF24_DATARATE=\(RF24_250KBPS\) -DMY_DEBUG_VERBOSE_RF24" Now I think I have an working OrangePi-Gateway without signing but with interrupt enabled. If there are new problems I will come back here. The next step for me is to activate signing again and bring the node into homeassistant.
FTDI/Serial or USB?
Hardware • serial usb ftdi serial monitor • • Samuel235

10

0
Votes

10
Posts

3219
Views

Actually, I use the FTDI connector on my outdoor weather sensor to power it from the solar/Li-Ion charger board. Used angled headers to keep the height down. I'll try to post a picture asap.
Possible to use different D pins for radio?
Hardware • lcd • • Muxje

2

0
Votes

2
Posts

1194
Views

Search for SoftSPI.
💬 Smart Sensors Shield
OpenHardware.io • esp8266 iot i2c shield adc uart control esp8266 iot board • • openhardware.io

1

0
Votes

1
Posts

837
Views

No one has replied

28
Online

11.6k
Users

11.2k
Topics

113.0k
Posts

Copyright 2019 TBD | Forum Guidelines | Privacy Policy | Terms of Service

1 / 1